Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  U012987  Lost Communication With Brake System Control Module Missing Message  


DESCRIPTION

The TCM receives signals from the skid control ECU via CAN communication. When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before performing troubleshooting for each corresponding ECU or sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U012987 Lost Communication With Brake System Control Module Missing Message No communication between the TCM and skid control ECU (brake actuator assembly) for 2.4 seconds or more (1-trip detection logic)
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

TCM


Comes on DTC stored SAE Code:
U0129

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait for 5 seconds or more with the ignition switch ON.

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: U012987.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CLEAR DTC AND PERFORM ROAD TEST
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373
HINT:

Write down the currently output DTCs before clearing them.



b.

Start the engine and drive the vehicle at a low speed.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT (DTC U012987)
2.CHECK DTC OUTPUT (DTC U012987)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC U012987 is not output A
DTC U012987 is output B



A

B