Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0374959 AUTOMATIC TRANSAXLE SYSTEM C

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P16B09F  Actuator Cut Circuit Stuck Off  


DESCRIPTION

The ECM monitors its internal operation. If it detects a malfunction, the electronic throttle motor circuit inside the ECM is shut off to ensure the safety of the vehicle.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P16B09F Actuator Cut Circuit Stuck Off ECM main CPU malfunction (1 trip detection logic). ECM Comes on DTC stored SAE Code:
P16B0

MONITOR DESCRIPTION

When the EFI main relay is operated by the ECM after the ignition switch is turned off, if the electronic throttle motor circuit is detected as not being shut off correctly, the ECM will illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

7.

Input the DTC: P16B09F.

8.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373
HINT:

Write down the currently output DTCs before clearing them.



e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P16B09F)
2.READ OUTPUT DTC (DTC P16B09F)
a.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON and wait for 1 minute or more.


d.

Turn the ignition switch off and wait for 2 minutes or more.

HINT:

This DTC is detected after the ignition switch is turned off.



e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

i.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTCs are not output A
DTC P16B09F is output B



A

B

3.REPLACE ECM
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT