Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076122 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0374958 AUTOMATIC TRANSAXLE SYSTEM C

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P077512  Pressure Control Solenoid "B" Circuit Short to Battery  


DESCRIPTION

Changing gears is performed by the ECM turning the solenoid (SL1, SL2, SL3, SL4, SL5 and SL6) valves on and off.

If an open or short occurs in any of the solenoid valve circuits, the ECM controls the remaining normal solenoid valves to allow the vehicle to be driven. If all of the solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short occurs in a solenoid valve circuit, the ECM cuts power to the malfunctioning solenoid valve.

HINT:

The following table shows normal operation of the solenoid (SL2) valve when the shift lever is in D.

Solenoid Valve Operation:
Gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Solenoid (SL2) Valve OFF OFF OFF OFF ON ON ON ON


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P077512 Pressure Control Solenoid "B" Circuit Short to Battery While the vehicle is being driven so that gear changes occur, a short to +B is detected in the solenoid (SL2) valve circuit for 1 second or more (1-trip detection logic).
·

Solenoid (SL2) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P0967

MONITOR DESCRIPTION

This DTC indicates a short to +B in the solenoid (SL2) valve circuit. The ECM commands gear shifts by turning the solenoid valves on or off. When there is an open or short in any solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores a DTC.

The ECM performs the fail-safe function and turns the other normal solenoid valves on or off. In the case of an open or short circuit, the ECM stops sending current to the open or shorted solenoid.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P077512.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C388294E47
1.021,2.833 1.479,3.031 0.458,0.198 11 false C30 1.01,3.01 2.844,3.208 1.833,0.198 10 false Transmission Wire 1.083,1.552 2.729,2.063 1.646,0.51 10 false Solenoid (SL2) Valve 0.74,1.219 0.896,1.417 0.156,0.198 10 false 1 0.75,1.969 0.906,2.167 0.156,0.198 10 false 2 5.25,0.844 5.865,1.042 0.615,0.198 10 false SL2+ 5.25,2.073 5.865,2.271 0.615,0.198 10 false SL2- 5.042,0.844 5.354,1.042 0.313,0.198 10 false 6 5.042,2.073 5.354,2.271 0.313,0.198 10 false 5 5.677,2.885 6.906,3.104 1.229,0.219 10 false C41 5.688,3.052 6.406,3.438 0.719,0.385 10 false ECM 5.969,0.615 6.583,0.813 0.615,0.198 10 false 12 V 2.469,0.844 3.083,1.042 0.615,0.198 10 false SL2+ 2.49,2.063 3.104,2.26 0.615,0.198 10 false SL2- 2.906,0.844 3.219,1.042 0.313,0.198 10 false 19 2.917,2.063 3.229,2.26 0.313,0.198 10 false 18

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND TRANSMISSION WIRE (TRANSMISSION WIRE (SOLENOID (SL2) VALVE) - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-6 (SL2+) or C41-5 (SL2-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-19 (SL2+) or C41-6 (SL2+) - Other terminals Always 10 kΩ or higher
C30-18 (SL2-) or C41-5 (SL2-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SL2) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.INSPECT SOLENOID (SL2) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SL2) Valve)


Remove the solenoid (SL2) valve.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL2) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG