Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076122 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0374958 AUTOMATIC TRANSAXLE SYSTEM C

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P079112  Intermediate Shaft Speed Sensor "A" Circuit Short to Battery  P079114  Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open  P079131  Intermediate Shaft Speed Sensor "A" No Signal  


DESCRIPTION

The transmission revolution sensor (NC) detects the rotation speed of the counter gear which shows the output shaft speed of automatic transaxle assembly.

Based on the transmission revolution sensor (NC) signal and the transmission revolution sensor (NT) signal, the ECM controls engine torque and shift timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P079112 Intermediate Shaft Speed Sensor "A" Circuit Short to Battery All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or higher.

·

The ignition switch is ON.

·

The starter is off.

·

Transmission revolution sensor (NC) input voltage is higher than 1.9 V for 2 seconds or more.


·

Transmission revolution sensor (NC)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code
P07C6
P079114 Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or higher.

·

The ignition switch is ON.

·

The starter is off.

·

Transmission revolution sensor (NC) input voltage is below 0.1 V for 2 seconds or more.


·

Transmission revolution sensor (NC)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code
P07C5
P079131 Intermediate Shaft Speed Sensor "A" No Signal All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or higher.

·

Park/neutral position switch D input signal is ON.

·

The vehicle speed is 25 km/h (15.54 mph) or more.

·

Speed indicated by transmission revolution sensor (NT) is the specified value or more.

·

Speed indicated by transmission revolution sensor (NC) is less than 300 rpm for 2 seconds or more.


·

Transmission revolution sensor (NC)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code
P0793

DTC Detection Condition Patterns (P079131):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnostic Condition The battery voltage is 8 V or higher. ○ ○ ○ ○
Park/neutral position switch D input signal is ON. ○ ○ ○ ○
The vehicle speed is 25 km/h (15.54 mph) or more. ○ ○ ○ ○
When the vehicle is being driven in 1st gear, the transmission revolution sensor (NT) value is 2390 rpm or more. ○ - - -
When the vehicle is being driven in 2nd gear, the transmission revolution sensor (NT) value is 1380 rpm or more. - ○ - -
When the vehicle is being driven in 3rd gear, the transmission revolution sensor (NT) value is 890 rpm or more. - - ○ -
When the vehicle is being driven in 4th gear, the transmission revolution sensor (NT) value is 620 rpm or more. - - - ○
Malfunction Condition Speed indicated by transmission revolution sensor (NC) is less than 300 rpm. ○ ○ ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic 1-trip detection logic 1-trip detection logic

DTC Detection Condition Patterns (P079131):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnostic Condition The battery voltage is 8 V or higher. ○ ○ ○ ○
Park/neutral position switch D input signal is ON. ○ ○ ○ ○
The vehicle speed is 25 km/h (15.54 mph) or more. ○ ○ ○ ○
When the vehicle is being driven in 5th gear, the transmission revolution sensor (NT) value is 540 rpm or more. ○ - - -
When the vehicle is being driven in 6th gear, the transmission revolution sensor (NT) value is 440 rpm or more. - ○ - -
When the vehicle is being driven in 7th gear, the transmission revolution sensor (NT) value is 350 rpm or more. - - ○ -
When the vehicle is being driven in 8th gear, the transmission revolution sensor (NT) value is 300 rpm or more. - - - ○
Malfunction Condition Speed indicated by transmission revolution sensor (NC) is less than 300 rpm. ○ ○ ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic 1-trip detection logic 1-trip detection logic

HINT:

DTC P079131 is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

The transmission revolution sensor (NC) monitors the output shaft speed.

The ECM commands gear changes and controls the lock up timing based on the signals from the transmission revolution sensor (NC) and throttle position sensor.

If the vehicle is being driven at 25 km/h (15.54 mph) or more and the speed sensor (NC) signal sent to the ECM is less than 300 rpm, or if the transmission revolution sensor (NC) input signal voltage is below 0.1 V or higher than 1.9 V, the ECM will illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P079112, P079114 or P079131.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C367619E30
1,1.729 2.563,2.219 1.563,0.49 10 false Transmission Revolution Sensor (NC) 1.219,3.052 2.781,3.542 1.563,0.49 10 false Transmission Wire 5.427,3.188 6.396,3.406 0.969,0.219 10 false C41 5.438,3.354 5.896,3.552 0.458,0.198 10 false ECM 5.135,2.271 5.594,2.469 0.458,0.198 10 false NCO 4.844,2.271 5.302,2.469 0.458,0.198 10 false 34 4.833,1.146 5.292,1.344 0.458,0.198 10 false 33 5.135,1.146 5.594,1.344 0.458,0.198 10 false NCB 5.708,0.854 6.167,1.052 0.458,0.198 10 false 12 V 2.729,1.146 3.188,1.344 0.458,0.198 10 false NCB 2.729,2.271 3.188,2.469 0.458,0.198 10 false NCO 3.135,2.271 3.594,2.469 0.458,0.198 10 false 21 3.135,1.146 3.594,1.344 0.458,0.198 10 false 22 0.625,1.396 1.083,1.594 0.458,0.198 10 false 1 0.635,2.219 1.094,2.417 0.458,0.198 10 false 2 1.219,2.896 1.677,3.094 0.458,0.198 10 false C30

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List / NC Sensor Speed.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC Sensor Speed Counter gear speed Min.: 0 rpm
Max.: 12750 rpm
- -
Powertrain > Transmission > Data List
Tester Display
NC Sensor Speed
50003 373 176
HINT:
·

NC Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.

·

NC Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 16 km/h (10 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS (NC SENSOR SPEED AND NC SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / NC Sensor Speed and NC Sensor Voltage.


e.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC Sensor Speed Counter gear speed Min.: 0 rpm
Max.: 12750 rpm
- -
NC Sensor Voltage NC sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling -
Powertrain > Transmission > Data List
Tester Display
NC Sensor Speed
NC Sensor Voltage
50003 373 176,177

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

5.REPLACE ECM

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NC) (NC TERMINAL)
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NC) (NC TERMINAL)
a.
C361134C29
1.469,0.146 1.906,0.417 0.438,0.271 1.292,1.25 0.833,1.75 true 1.375,1.26 1.75,1.75 true 1.563,0.198 2.021,0.396 0.458,0.198 10 false C30 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.688,1.813 1.146,2.01 0.458,0.198 10 false NCO 1.667,1.833 2.125,2.031 0.458,0.198 10 false NCB
*a Front view of wire harness connector
(to Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-21 (NCO) - Body ground Always 99 to 101 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C30-22 (NCB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC))

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC))
a.
C361135C04
1.698,1.385 1.333,1.917 true 1.885,1.385 2.333,1.917 true 2.031,3.708 1.75,4.167 true 2.125,3.708 2.5,4.167 true 0.75,0.667 1.063,0.865 0.313,0.198 10 false *a 0.75,2.75 1.063,2.948 0.313,0.198 10 false *b 1.271,1.99 1.427,2.188 0.156,0.198 10 false 1 2.292,1.979 2.448,2.177 0.156,0.198 10 false 2 1.583,4.177 2.042,4.375 0.458,0.198 10 false NCB 2.354,4.167 2.813,4.365 0.458,0.198 10 false NCO 0.083,0.083 0.542,0.281 0.458,0.198 10 false *1
*1 Transmission Wire
*a Transmission Revolution Sensor (NC) Side
*b Wire Harness Connector Side


Disconnect the transmission revolution sensor (NC) connector.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE>REMOVAL


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (transmission revolution sensor (NC) side) - 22 (NCB) (wire harness connector side) Always Below 1 Ω
2 (transmission revolution sensor (NC) side) - 21 (NCO) (wire harness connector side) Always Below 1 Ω
1 (transmission revolution sensor (NC) side) or 22 (NCB) (wire harness connector side) - Body ground Always 10 kΩ or higher
2 (transmission revolution sensor (NC) side) or 21 (NCO) (wire harness connector side) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NC)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-22 (NCB) - C41-33 (NCB) Always Below 1 Ω
C30-21 (NCO) - C41-34 (NCO) Always Below 1 Ω
C30-22 (NCB) or C41-33 (NCB) - Body ground Always 10 kΩ or higher
C30-21 (NCO) or C41-34 (NCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT