Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Open in Bus 1 Main Bus Line  


DESCRIPTION

There may be a short circuit between the CAN main bus wire and/or CAN branch wire when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 23 (CA1H) and 8 (CA1L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

Open in CAN main bus wire

·

Central gateway ECU (network gateway ECU)

·

No. 1 CAN junction terminal

·

No. 2 CAN junction connector

·

No. 8 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C369102E06
0.708,1.375 1.323,1.573 0.615,0.198 10 false CA1H 0.708,2.094 1.323,2.292 0.615,0.198 10 false CA1L 0.26,2.604 1.656,3.156 1.396,0.552 10 false Central Gateway ECU (Network Gateway ECU) 1.323,1.365 1.635,1.563 0.313,0.198 10 false 23 1.333,1.906 1.49,2.104 0.156,0.198 10 false 8 1.802,1.365 2.063,1.563 0.26,0.198 10 false 8 1.76,1.896 2.073,2.094 0.313,0.198 10 false 18 1.948,2.604 3.302,2.969 1.354,0.365 10 false No. 2 CAN Junction Connector 3.906,2.594 5.177,2.99 1.271,0.396 10 false No. 8 CAN Junction Connector 3.219,1.365 3.375,1.563 0.156,0.198 10 false 3 3.208,1.906 3.5,2.146 0.292,0.24 10 false 13 3.802,1.365 3.958,1.563 0.156,0.198 10 false 1 3.813,1.906 4.125,2.104 0.313,0.198 10 false 7 5.229,1.365 5.385,1.563 0.156,0.198 10 false 4 5.208,1.906 5.521,2.104 0.313,0.198 10 false 10 5.719,1.365 6.031,1.563 0.313,0.198 10 false 3 5.729,1.906 6.042,2.104 0.313,0.198 10 false 2 5.854,2.583 7.083,3.01 1.229,0.427 10 false No. 1 CAN Junction Terminal 6.052,1.375 6.667,1.573 0.615,0.198 10 false CANH 6.083,2.104 6.698,2.302 0.615,0.198 10 false CANL 0.271,2.438 0.729,2.635 0.458,0.198 10 false G72 1.958,2.417 2.417,2.615 0.458,0.198 10 false G102 3.896,2.417 4.354,2.615 0.458,0.198 10 false N53 5.844,2.417 6.302,2.615 0.458,0.198 10 false N54

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 2 CAN junction connector.

C387411C40
0.313,1.219 0.75,1.5 0.438,0.281 1.719,0.583 1.885,0.583 1.885,0.583 2.635,1.427 true 1.521,2.323 1.688,2.323 1.688,2.323 2.615,1.656 true 5.115,0.656 4.865,0.656 4.865,0.656 4.51,1.417 true 5.031,2.094 4.781,2.094 4.781,2.094 4.5,1.604 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,1.281 0.781,1.49 0.406,0.208 10 false G102 0.969,2.24 1.552,2.448 0.583,0.208 10 false CANL*b 1.135,0.5 1.719,0.708 0.583,0.208 10 false CANH*b 5.104,2.042 5.688,2.25 0.583,0.208 10 false CANL*c 5.198,0.583 5.781,0.76 0.583,0.177 10 false CANH*c
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 8 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G102-3 (CANH) - G102-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 8 CAN junction connector
G102-8 (CANH) - G102-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 8 CAN junction connector CAN main wire) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.
C368242C39
1.417,0.24 1.958,0.458 0.542,0.219 2.427,1.302 2.26,1.854 2.26,1.854 2.427,1.854 true 2.344,1.094 2.448,0.677 2.448,0.677 2.615,0.677 true 1.563,0.281 2.021,0.479 0.458,0.198 10 false G72 2.677,0.625 3.135,0.823 0.458,0.198 10 false CA1L 2.49,1.792 2.948,1.99 0.458,0.198 10 false CA1H 0.073,0.042 0.531,0.24 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-23 (CA1H) - G72-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.

Disconnect the No. 8 CAN junction connector.

C387413C67
0.719,1.219 1.125,1.448 0.406,0.229 1.948,0.729 2.125,0.729 2.125,0.729 2.438,1.302 true 1.927,2.094 2.156,2.094 2.156,2.094 2.417,1.563 true 4.833,0.427 4.656,0.427 4.656,0.427 3.792,1.323 true 4.438,2.177 4.25,2.177 4.25,2.177 3.833,1.615 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.771,1.25 1.135,1.406 0.365,0.156 10 false N53 1.354,0.646 1.906,0.823 0.552,0.177 10 false CANH*b 1.344,1.99 1.896,2.167 0.552,0.177 10 false CANL*b 4.917,0.323 5.521,0.51 0.604,0.188 10 false CANH*c 4.5,2.094 5.052,2.271 0.552,0.177 10 false CANL*c
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to No. 1 CAN Junction Terminal - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
N53-1 (CANH) - N53-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
N53-4 (CANH) - N53-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction terminal



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction terminal CAN main wire) B
NG (No. 2 CAN junction connector CAN main wire) C



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)
a.

Reconnect the N53 No. 8 CAN junction connector.


b.
C369111C26
1.5,0.333 1.917,0.583 0.417,0.25 1.729,1.135 1.563,0.667 1.563,0.667 1.417,0.667 true 1.948,1.146 2.073,0.667 2.073,0.667 2.24,0.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.594,0.375 2.104,0.615 0.51,0.24 10 false N54 2.281,0.604 2.771,0.865 0.49,0.26 10 false CANH 0.99,0.594 1.479,0.854 0.49,0.26 10 false CANL
*a Front view of wire harness connector
(to No. 1 CAN Junction Terminal)


Disconnect the No. 1 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N54-3 (CANH) - N54-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)