Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2018.10–2019.02
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

Open in CAN main bus wire

·

Central gateway ECU (network gateway ECU)

·

ECM

·

No. 3 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C409599E01
0.948,3.49 1.563,3.688 0.615,0.198 10 false G103 0.927,3.646 2.906,3.854 1.979,0.208 10 false No. 3 CAN Junction Connector 1.844,1.208 2.458,1.406 0.615,0.198 10 false 11 1.854,0.823 2.469,1.021 0.615,0.198 10 false 1 1.844,2.938 2.458,3.135 0.615,0.198 10 false 13 1.875,2.51 2.49,2.708 0.615,0.198 10 false 3 5.698,3.448 6.313,3.646 0.615,0.198 10 false A24 5.708,3.615 6.667,3.958 0.958,0.344 10 false ECM 5.146,1.583 5.76,1.781 0.615,0.198 10 false G72 5.146,1.74 7.094,2.167 1.948,0.427 10 false Central Gateway ECU (Network Gateway ECU) 5.354,0.823 5.583,1.021 0.229,0.198 10 false 18 5.344,1.229 5.563,1.427 0.219,0.198 10 false 17 5.625,0.823 6.094,0.99 0.469,0.167 10 false CA4H 5.635,1.438 6.25,1.635 0.615,0.198 10 false CA4L 5.615,2.552 6.229,2.75 0.615,0.198 10 false CANH 5.625,3.167 6.24,3.365 0.615,0.198 10 false CANL 5.396,2.552 5.594,2.75 0.198,0.198 10 false 8 5.365,2.938 5.583,3.135 0.219,0.198 10 false 18

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C387411C41
0.313,1.219 0.75,1.5 0.438,0.281 1.24,0.927 1.406,0.927 1.406,0.927 1.865,1.396 true 1.135,1.979 1.302,1.979 1.302,1.979 1.865,1.604 true 1.719,0.667 1.885,0.667 1.885,0.667 2.604,1.375 true 1.51,2.344 1.677,2.344 1.677,2.344 2.635,1.615 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,1.281 0.781,1.49 0.406,0.208 10 false G103 0.604,1.896 1.188,2.104 0.583,0.208 10 false CANL*b 0.677,0.854 1.26,1.063 0.583,0.208 10 false CANH*b 0.969,2.26 1.552,2.469 0.583,0.208 10 false CANL*c 1.177,0.583 1.76,0.792 0.583,0.208 10 false CANH*c
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to ECM - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G103-1 (CANH) - G103-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
G103-3 (CANH) - G103-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (ECM CAN main wire) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 3 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the G103 No. 3 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C409595C01
1.448,0.104 1.917,0.323 0.469,0.219 1.24,1.833 1.448,1.833 1.448,1.833 1.646,1.188 true 2.167,1.823 2,1.823 2,1.823 1.781,1.188 true 0.885,1.75 1.344,1.948 0.458,0.198 10 false CA4L 1.563,0.125 2.021,0.323 0.458,0.198 10 false G72 2.219,1.74 2.677,1.938 0.458,0.198 10 false CA4H 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-18 (CA4H) - G72-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the G103 No. 3 CAN junction connector.


b.

Disconnect the ECM connector.


c.
C405888C02
1.417,0.167 1.813,0.417 0.396,0.25 1.802,1.292 2.25,0.167 2.25,0.167 2.417,0.167 true 1.823,1.427 2.5,0.458 2.5,0.458 2.667,0.458 true 1.49,0.208 1.948,0.406 0.458,0.198 10 false A24 0.167,0.104 0.625,0.302 0.458,0.198 10 false *a 2.49,0.083 2.948,0.281 0.458,0.198 10 false CANH 2.75,0.396 3.208,0.594 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-8 (CANH) - A24-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 3 CAN JUNCTION CONNECTOR)