Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2018.10–2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 3 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area

*1: w/ Telematics System

*2: w/ Bus Buffer ECU

*3: for Radio and Display Type

·

There is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

·

There is no resistance between terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.


·

Short to +B in CAN main bus wire

·

Short to +B in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Telephone transceiver assembly*1

·

Bus buffer ECU*2

·

Radio and display receiver assembly*3

·

No. 5 CAN junction connector



WIRING DIAGRAM

C379634E20
0.219,1.208 0.677,1.406 0.458,0.198 10 false G2 0.24,1.365 1.927,1.76 1.688,0.396 10 false Radio and Display Receiver Assembly*3 0.927,0.635 1.385,0.833 0.458,0.198 10 false CANH 0.927,1.01 1.385,1.208 0.458,0.198 10 false CANL 0.906,2.385 1.365,2.583 0.458,0.198 10 false CANP 0.906,2.781 1.365,2.979 0.458,0.198 10 false CANN 0.927,4.125 1.385,4.323 0.458,0.198 10 false CAN+ 0.906,4.51 1.365,4.708 0.458,0.198 10 false CAN- 5.104,4.781 5.563,4.979 0.458,0.198 10 false G72 5.104,4.948 7.094,5.333 1.99,0.385 10 false Central Gateway ECU (Network Gateway ECU) 0.333,3.073 1.208,3.292 0.875,0.219 10 false H6 0.323,3.25 1.698,3.75 1.375,0.5 10 false Telephone Transceiver Assembly*1 0.25,4.75 0.708,4.948 0.458,0.198 10 false G80 0.271,4.896 2.281,5.156 2.01,0.26 10 false Bus Buffer ECU*2 1.385,4.021 1.844,4.219 0.458,0.198 10 false 2 1.396,4.375 1.854,4.573 0.458,0.198 10 false 1 1.375,2.26 1.833,2.458 0.458,0.198 10 false 15 1.385,2.656 1.844,2.854 0.458,0.198 10 false 16 1.375,0.521 1.833,0.719 0.458,0.198 10 false 13 1.385,0.927 1.844,1.125 0.458,0.198 10 false 14 3.167,0.521 3.625,0.719 0.458,0.198 10 false 5 3.115,0.906 3.573,1.104 0.458,0.198 10 false 16 4.135,0.5 4.594,0.698 0.458,0.198 10 false 2 4.125,0.906 4.583,1.104 0.458,0.198 10 false 13 5.708,0.542 6.167,0.74 0.458,0.198 10 false 6 5.667,0.917 6.125,1.115 0.458,0.198 10 false 21 3.104,2.656 3.563,2.854 0.458,0.198 10 false 14 3.177,2.24 3.635,2.438 0.458,0.198 10 false 3 3.104,4.406 3.563,4.604 0.458,0.198 10 false 12 3.146,3.99 3.604,4.188 0.458,0.198 10 false 1 4.104,3.99 4.563,4.188 0.458,0.198 10 false 4 4.083,4.396 4.542,4.594 0.458,0.198 10 false 15 5.688,4.01 6.146,4.208 0.458,0.198 10 false 19 5.677,4.417 6.135,4.615 0.458,0.198 10 false 20 5.938,4 6.396,4.198 0.458,0.198 10 false CAYH 5.958,4.625 6.417,4.823 0.458,0.198 10 false CAYL 5.969,0.479 6.427,0.677 0.458,0.198 10 false CA3H 5.948,1.135 6.406,1.333 0.458,0.198 10 false CA3L 2.844,4.771 3.302,4.969 0.458,0.198 10 false G105 2.844,4.927 5.031,5.208 2.188,0.281 10 false No. 5 CAN Junction Connector 0.25,5.479 2.26,5.74 2.01,0.26 10 false *1: w/ Telematics System 2.24,5.49 4.25,5.75 2.01,0.26 10 false *2: w/ Bus Buffer ECU 4.083,5.49 7.01,5.74 2.927,0.25 10 false *3: for Radio and Display Type

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio receiver assembly, be sure to replace it with new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.

C409618C01
0.396,1.406 0.813,1.615 0.417,0.208 4.313,1.406 4.729,1.615 0.417,0.208 1.229,1.146 1.396,1.146 1.396,1.146 1.563,1.396 true 1.125,1.917 1.292,1.917 1.292,1.917 1.479,1.75 true 1.302,0.896 1.469,0.896 1.469,0.896 1.76,1.396 true 1.271,2.094 1.438,2.094 1.438,2.094 1.719,1.75 true 1.375,0.646 1.542,0.646 1.542,0.646 1.885,1.375 true 1.406,2.302 1.573,2.302 1.573,2.302 1.875,1.76 true 2.552,0.323 2.385,0.323 2.385,0.323 2.052,1.375 true 2.438,2.292 2.271,2.292 2.271,2.292 2.063,1.75 true 2.792,0.594 2.625,0.594 2.625,0.594 2.229,1.385 true 2.667,2.115 2.5,2.115 2.5,2.115 2.219,1.75 true 6.302,0.917 6.135,0.917 6.135,0.917 5.979,1.521 true 0.542,0.208 0.854,0.406 0.313,0.198 10 false *a 3.938,0.198 4.25,0.396 0.313,0.198 10 false *g 0.677,1.083 1.396,1.302 0.719,0.219 10 false CANH*b 0.656,1.76 1.375,1.979 0.719,0.219 10 false CANL*b 0.771,0.792 1.49,1.01 0.719,0.219 10 false CANH*c 0.75,2.01 1.469,2.229 0.719,0.219 10 false CANL*c 0.875,0.573 1.594,0.792 0.719,0.219 10 false CANH*d 0.896,2.229 1.615,2.417 0.719,0.188 10 false CANL*d 2.604,0.26 3.323,0.479 0.719,0.219 10 false CANH*e 2.813,0.521 3.531,0.74 0.719,0.219 10 false CANH*f 2.698,2.063 3.396,2.271 0.698,0.208 10 false CANL*f 2.5,2.229 3.198,2.438 0.698,0.208 10 false CANL*e 6.344,0.813 7.042,1.021 0.698,0.208 10 false BAT 4.385,1.427 5.083,1.635 0.698,0.208 10 false G114 0.458,1.438 1.156,1.646 0.698,0.208 10 false G105
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Bus Buffer ECU (w/ Bus Buffer ECU)
*c to Central Gateway ECU (Network Gateway ECU) *d to Telephone Transceiver Assembly (w/ Telematics System)
*e to Central Gateway ECU (Network Gateway ECU) *f to Radio and Display Receiver Assembly (for Radio and Display Type)
*g Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Telematics System

*2: w/ Bus Buffer ECU

*3: for Radio and Display Type

G105-1 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Bus buffer ECU*2
G105-12 (CANH) - G114-16 (BAT)
G105-2 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
G105-13 (CANL) - G114-16 (BAT)
G105-3 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Telephone transceiver assembly*1
G105-14 (CANL) - G114-16 (BAT)
G105-4 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
G105-15 (CANL) - G114-16 (BAT)
G105-5 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Radio and display receiver assembly*3
G105-16 (CANL) - G114-16 (BAT)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the G105 No. 5 CAN junction connector.


b.
C406353C66
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.729,2.104 2.531,2.104 2.531,2.104 2.198,1.521 true 2.75,0.667 2.552,0.667 2.552,0.667 2.302,1.229 true 2.531,4.292 2.365,4.292 2.365,4.292 2.365,3.708 true 1.563,0.292 2.177,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 2.813,0.594 3.302,0.781 0.49,0.188 10 false CA3H 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.792,2.031 3.24,2.24 0.448,0.208 10 false CA3L 2.604,4.219 3.219,4.417 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-6 (CA3H) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G72-21 (CA3L) - G114-16 (BAT)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.
C406381C32
1.5,0.083 1.917,0.333 0.417,0.25 0.417,2.583 0.833,2.833 0.417,0.25 2.198,2.927 2.417,3.167 2.417,3.167 2.583,3.167 true 1.396,0.875 1.24,1.427 1.24,1.427 1.073,1.427 true 1.104,0.323 1.271,0.323 1.271,0.323 1.406,0.771 true 0.469,2.625 0.927,2.823 0.458,0.198 10 false G114 0.698,0.25 1.156,0.448 0.458,0.198 10 false CA3H 1.583,0.135 2.042,0.333 0.458,0.198 10 false G72 0.698,1.344 1.156,1.542 0.458,0.198 10 false CA3L 2.615,3.104 3.073,3.302 0.458,0.198 10 false BAT 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.135,2.115 0.594,2.313 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus wire shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-6 (CA3H) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G72-21 (CA3L) - G114-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR