Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2018.10–2019.02
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

ECM main wire or connector

·

ECM branch wire or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C405924E03
5.792,5.594 6.104,5.792 0.313,0.198 10 false EC 5.781,6.417 6.094,6.615 0.313,0.198 10 false E2 5.781,6.729 6.458,6.927 0.677,0.198 10 false E1D1 5.604,0.385 5.917,0.583 0.313,0.198 10 false 8 5.552,0.75 5.865,0.948 0.313,0.198 10 false 18 5.594,3.896 5.906,4.094 0.313,0.198 10 false 1 5.604,4.49 5.917,4.688 0.313,0.198 10 false 2 1.573,0.74 1.885,0.938 0.313,0.198 10 false 13 1.583,0.375 1.896,0.573 0.313,0.198 10 false 3 5.542,5.052 5.854,5.25 0.313,0.198 10 false 15 5.542,6.031 5.854,6.229 0.313,0.198 10 false 10 5.542,6.344 5.854,6.542 0.313,0.198 10 false 36 5.542,6.625 5.854,6.823 0.313,0.198 10 false 54 5.792,5.146 6.292,5.365 0.5,0.219 10 false MREL 5.781,3.406 6.281,3.625 0.5,0.219 10 false +B2 5.802,2.823 6.302,3.042 0.5,0.219 10 false +B 5.802,4.583 6.302,4.802 0.5,0.219 10 false IGSW 5.792,4.01 6.292,4.229 0.5,0.219 10 false BATT 5.833,0.958 6.333,1.177 0.5,0.219 10 false CANL 5.833,0.375 6.333,0.594 0.5,0.219 10 false CANH 4.25,3.854 5.51,4.177 1.26,0.323 10 false EFI-MAIN NO.4 4.26,4.448 5.271,4.688 1.01,0.24 10 false ECU IG2 NO.2 2.313,4.594 3.833,4.875 1.521,0.281 10 false from IG2 NO.1 Relay 2.271,3.99 3.938,4.25 1.667,0.26 10 false from Auxiliary Battery 1.948,3.365 3.75,3.667 1.802,0.302 10 false from EFI-MAIN NO.1 Relay 5.948,7.354 6.479,7.75 0.531,0.396 10 false ECM 0.26,1.229 2.406,1.49 2.146,0.26 10 false No. 3 CAN Junction Connector 0.271,1.042 0.771,1.26 0.5,0.219 10 false G103 5.594,2.74 5.906,2.938 0.313,0.198 10 false 9 5.542,3.323 5.854,3.521 0.313,0.198 10 false 35 5.552,5.5 5.865,5.698 0.313,0.198 10 false 45 5.781,6.146 6.094,6.344 0.313,0.198 10 false E1 2.073,5.125 3.906,5.49 1.833,0.365 10 false to EFI-MAIN NO.1 Relay 5.698,7.198 6.01,7.396 0.313,0.198 10 false A24 0.229,2.698 2.375,2.958 2.146,0.26 10 false No. 4 CAN Junction Connector 0.229,2.479 0.729,2.698 0.5,0.219 10 false G104 5.594,1.813 5.906,2.01 0.313,0.198 10 false 7 5.531,2.219 5.844,2.417 0.313,0.198 10 false 17 5.781,1.906 6.281,2.125 0.5,0.219 10 false CAN+ 5.781,2.302 6.281,2.521 0.5,0.219 10 false CAN- 1.594,1.833 1.906,2.031 0.313,0.198 10 false 6 1.583,2.198 1.896,2.396 0.313,0.198 10 false 12

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM MAIN WIRE AND BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C405888C06
1.417,0.167 1.813,0.417 0.396,0.25 1.833,1.448 2.729,0.74 2.729,0.74 2.896,0.74 true 1.823,1.344 2.708,0.542 2.708,0.542 2.875,0.542 true 1.719,1.302 2.688,0.302 2.688,0.302 2.854,0.302 true 1.073,0.521 1.24,0.521 1.24,0.521 1.698,1.406 true 1.49,0.208 1.948,0.406 0.458,0.198 10 false A24 0.167,0.104 0.625,0.302 0.458,0.198 10 false *a 2.948,0.469 3.406,0.667 0.458,0.198 10 false CANH 2.969,0.667 3.427,0.865 0.458,0.198 10 false CANL 2.927,0.229 3.385,0.427 0.458,0.198 10 false CAN+ 0.667,0.438 1.125,0.635 0.458,0.198 10 false CAN-
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-8 (CANH) - A24-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A24-7 (CAN+) - A24-17 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector main wire) B
NG (No. 4 CAN junction connector branch wire) C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C405888C12
1.417,0.167 1.813,0.417 0.396,0.25 2.406,1.385 2.802,0.604 2.802,0.604 2.969,0.604 true 1.031,2.021 0.479,3.083 0.479,3.083 0.646,3.083 true 1.021,1.302 0.688,0.594 0.688,0.594 0.521,0.594 true 2.167,1.396 2.635,0.323 2.635,0.323 2.802,0.323 true 2.073,1.74 2.156,3.104 2.156,3.104 2.323,3.104 true 1.146,1.323 0.958,0.438 0.958,0.438 0.792,0.438 true 2.375,2.073 2.698,2.938 2.698,2.938 2.865,2.938 true 2.417,1.792 2.906,2.677 2.906,2.677 3.052,2.677 true 1.479,1.417 1.948,0.344 1.948,0.344 2.115,0.344 true 1.49,0.208 1.948,0.406 0.458,0.198 10 false A24 0.104,0.063 0.563,0.26 0.458,0.198 10 false *a 2.906,2.865 3.313,3.094 0.406,0.229 10 false E1D1 0.698,3.031 1.156,3.229 0.458,0.198 10 false EC 0.115,0.521 0.573,0.719 0.458,0.198 10 false BATT 2.854,0.24 3.177,0.458 0.323,0.219 10 false +B 2.365,3.021 2.823,3.219 0.458,0.198 10 false +B2 0.344,0.333 0.802,0.531 0.458,0.198 10 false IGSW 3.042,0.521 3.365,0.74 0.323,0.219 10 false E1 3.104,2.583 3.427,2.802 0.323,0.219 10 false E2 2.167,0.302 2.656,0.573 0.49,0.271 10 false MREL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-45 (EC) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A24-10 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A24-36 (E2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A24-54 (E1D1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-1 (BATT) - Body ground Power switch off 11 to 14 V
A24-9 (+B) - Body ground Auxiliary battery positive (+) voltage applied to terminal A24-15 (MREL) 11 to 14 V
A24-35 (+B2) - Body ground Auxiliary battery positive (+) voltage applied to terminal A24-15 (MREL) 11 to 14 V
A24-2 (IGSW) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR