Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Certification (Smart)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Certification (Smart)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Certification ECU (smart key ECU assembly) branch wire or connector

·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) ground circuit

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C348640E34
5.156,4.781 5.729,4.969 0.573,0.188 10 false G54 5.146,4.948 6.719,5.719 1.573,0.771 10 false Certification ECU (Smart Key ECU Assembly) 5.594,4.167 6.438,4.385 0.844,0.219 10 false E 5.594,3.344 6.438,3.563 0.844,0.219 10 false CUTB 5.583,2.521 6.427,2.74 0.844,0.219 10 false +B 5.375,2.417 6.219,2.635 0.844,0.219 10 false 4 5.302,3.24 6.146,3.458 0.844,0.219 10 false 15 5.292,4.063 6.135,4.281 0.844,0.219 10 false 18 1.656,0.927 2.5,1.198 0.844,0.271 10 false 2 1.552,2.521 3.302,3.021 1.75,0.5 10 false from Auxiliary Battery 3.865,3.198 5.031,3.406 1.167,0.208 10 false ECU-DCC NO.2 5.594,1 6.438,1.219 0.844,0.219 10 false CANH 5.594,1.625 6.438,1.844 0.844,0.219 10 false CANL 5.365,1.521 6.208,1.74 0.844,0.219 10 false 2 5.365,0.917 6.208,1.135 0.844,0.219 10 false 1 0.229,1.969 2.365,2.271 2.135,0.302 10 false G96 0.229,2.125 2.396,2.458 2.167,0.333 10 false No. 1 CAN Junction Connector 1.573,3.354 3.573,3.688 2,0.333 10 false from Auxiliary Battery 4.146,2.375 4.99,2.646 0.844,0.271 10 false AM2 1.656,1.531 2.5,1.802 0.844,0.271 10 false 13

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C369116C12
1.5,0.167 1.917,0.417 0.417,0.25 1.094,1.438 1.25,0.833 1.25,0.833 1.417,0.833 true 0.938,1.427 1.115,0.667 1.115,0.667 1.281,0.667 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.594,0.208 1.906,0.406 0.313,0.198 10 false G54 1.333,0.604 1.792,0.802 0.458,0.198 10 false CANH 1.469,0.781 1.927,0.979 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-1 (CANH) - G54-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369116C13
1.5,0.167 1.917,0.417 0.417,0.25 2.5,1.427 2.25,0.667 2.25,0.667 2,0.667 true 0.917,1.958 0.958,2.802 0.958,2.802 1.125,2.802 true 2.313,1.698 2.344,2.656 2.344,2.656 2.531,2.656 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.583,0.208 1.896,0.406 0.313,0.198 10 false G54 1.188,2.719 1.646,2.917 0.458,0.198 10 false E 1.802,0.615 2.26,0.813 0.458,0.198 10 false +B 2.615,2.594 3.073,2.792 0.458,0.198 10 false CUTB
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-18 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-4 (+B) - Body ground Power switch off 11 to 14 V
G54-15 (CUTB) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR