Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E301406E58
5.073,2.865 6.417,3.104 1.344,0.24 10 false Parking Assist ECU 5.083,2.688 5.542,2.885 0.458,0.198 10 false N25 5.333,2.156 6.01,2.375 0.677,0.219 10 false GND1 5.333,1.74 6.01,1.958 0.677,0.219 10 false ACC 5.333,1.313 6.01,1.531 0.677,0.219 10 false IG 5.323,0.885 6,1.104 0.677,0.219 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 1 5.115,1.188 5.271,1.385 0.156,0.198 10 false 3 5.104,1.625 5.26,1.823 0.156,0.198 10 false 2 5.125,2.021 5.281,2.219 0.156,0.198 10 false 4 3.229,1.094 4.76,1.292 1.531,0.198 10 false ECU-B NO.2 3.208,1.521 4.74,1.719 1.531,0.198 10 false ECU-IG1 NO.3 3.344,1.927 4.021,2.146 0.677,0.219 10 false ECU-ACC 1.385,0.865 3.99,1.063 2.604,0.198 10 false from Battery 0.948,1.302 3.552,1.5 2.604,0.198 10 false from IG1 NO.1 Relay 1.177,1.719 3.781,1.917 2.604,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>CALIBRATION

·

Inspect the fuse for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
E245332C46
1.417,0.25 1.917,0.5 0.5,0.25 0.667,0.5 0.917,0.5 0.917,0.5 1.104,0.99 true 2.885,0.604 2.635,0.604 2.635,0.604 2.552,0.969 true 0.385,1 0.802,1 true 2.573,0.323 2.323,0.323 2.323,0.323 2.271,0.948 true 0.115,0.115 0.427,0.271 0.313,0.156 10 false *a 0.177,0.927 0.479,1.104 0.302,0.177 10 false +B 2.615,0.229 3.01,0.385 0.396,0.156 10 false IG 1.542,0.292 1.938,0.448 0.396,0.156 10 false N25 2.927,0.521 3.344,0.729 0.417,0.208 10 false GND1 0.354,0.417 0.74,0.594 0.385,0.177 10 false ACC
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N25-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N25-1 (+B) - N25-4 (GND1) Always 11 to 14 V
N25-2 (ACC) - N25-4 (GND1) Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V
N25-3 (IG) - N25-4 (GND1) Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR