Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM
RM3620E _52 Drivetrain _076960 GF1A TRANSFER / 4WD / AWD _0379782 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  C120C  Linear Solenoid Power Supply System Malfunction  


DESCRIPTION

This DTC is output by the 4WD ECU assembly if a malfunction occurs in the linear solenoid power supply system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C120C Linear Solenoid Power Supply System Malfunction
1.

When the 4WD relay is on, the 4WD relay monitor remains off for 1 second or more while the voltage at the IG1 terminal is 9.5 V or more

2.

When the 4WD relay is on, the 4WD relay monitor remains off for 1 second or more while the voltage at the IG1 terminal is less than 9.5 V

3.

While the 4WD relay is off, the 4WD relay monitor remains on for 1 second or more immediately after the ignition switch is turned to ON


·

Wire harness or connector

·

4WD ECU assembly



DTC Detection Conditions: C120C
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the 4WD relay is on and the voltage at the IG1 terminal is 9.5 V or more ○ - -
When the 4WD relay is on and the voltage at the IG1 terminal is less than 9.5 V - ○ -
While the 4WD relay is off - - ○
Malfunction Status The 4WD relay monitor remains off ○ ○ -
The 4WD relay monitor remains on immediately after the ignition switch is turned to ON - - ○
Detection Time 1 second or more 1 second or more 1 second or more
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C253611E11
2.417,1.073 3.563,1.396 1.146,0.323 10 false ECU-IG1 NO.2 3.729,0.76 3.958,0.99 0.229,0.229 10 false 3 3.958,0.823 4.271,1.01 0.313,0.188 10 false IG1 3.74,1.458 4.01,1.667 0.271,0.208 10 false 4 3.969,1.521 4.323,1.75 0.354,0.229 10 false GND 0.656,0.896 1.698,1.104 1.042,0.208 10 false from Battery 3.667,2.281 5.021,2.5 1.354,0.219 10 false 4WD ECU Assembly 3.667,2.083 4.021,2.292 0.354,0.208 10 false N5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C76
2.385,0.104 2.792,0.365 0.406,0.26 1.938,1.927 2.24,1.927 2.24,1.927 2.333,1.177 true 1.677,1.854 2.021,2.052 0.344,0.198 10 false IG1 2.49,0.146 2.802,0.344 0.313,0.198 10 false N5 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N5-3 (IG1) -Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N5-4 (GND) -Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Turn the ignition switch to ON.


c.

Check that no DTCs other than DTC C120C have been output.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Proceed to
DTCs other than C120C are not output
DTCs other than C120C are output




DTCs other than C120C are not output

DTCs other than C120C are output