When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.
Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>CALIBRATION
Turn the ignition switch off.
Connect the GTS the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Four Wheel Drive / Dual Data List.
Simultaneously display the "Off-road Mode Selection Signal" four wheel drive Data List item and the "Off-road Guidance Status" engine Data List item.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Off-road Mode Selection Signal | Off-road Mode Selection Signal | Normal / Grass & Snow / Mud & Sand / Loose Rock / Mogul / Rock & Dirt / Rock / E-Lock | - | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Off-road Guidance Status | Off road mode status | Normal, Grass & Snow, Mud & Sand, Loose Rock, Mogul or Rock & Dirt | - | - |
Operate the multi-terrain select switch (integration control and panel assembly) and check that the Data List display and multi-information display message change according to switch operation.
| Multi-terrain Select Switch (Integration Control and Panel Assembly) Operation | Data List Display | Multi-information Display Message |
|---|---|---|
| NORMAL | Normal | NORMAL |
| MUD&SAND | Mud & Sand | MUD&SAND |
| ROCK&DIRT | Rock & Dirt | ROCK&DIRT |
| Result | Proceed to |
|---|---|
| When the switch is operated, the Data List display (Off-road Mode Selection Signal and Off-road Guidance Status ) and message do not change | A |
| When the switch is operated, the Data List display (Off-road Mode Selection Signal) changes, but the Data List display (Off-road Guidance Status ) and message do not change | B |
| When the switch is operated, the Data List display (Off-road Mode Selection Signal and Off-road Guidance Status) change, but the message does not change | C |
| When the switch is operated, the Data List display and message change normally | D |
A
B
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
C
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
D
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the multi-terrain select switch (integration control and panel assembly).
Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>MULTI-TERRAIN SELECT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the N4 4WD ECU assembly connector.
Disconnect the G32 multi-terrain select switch (integration control and panel assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N4-18 (OMS) - G32-18 (B) | Always | Below 1 Ω |
| N4-19 (OMSG) - G32-17 (E) | Always | Below 1 Ω |
| N4-18 (OMS) or G32-18 (B) - Body ground | Always | 10 kΩ or higher |
| N4-19 (OMSG) or G32-17 (E) - Body ground | Always | 10 kΩ or higher |
| N4-18 (OMS) or G32-18 (B) - N4-19 (OMSG) or G32-17 (E) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG