Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 4 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main bus wire

·

Short to GND in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly

·

ECM

·

Steering sensor

·

Rack and pinion power steering gear assembly

·

Brake booster with master cylinder assembly (skid control ECU)

·

Parking brake ECU assembly

·

Hybrid vehicle control ECU assembly

·

No. 1 CAN junction connector

·

No. 4 CAN junction connector

·

No. 6 CAN junction connector



WIRING DIAGRAM

C405921E03
0.083,0.927 1,1.125 0.917,0.198 10 false G72 0.083,1.063 2.021,1.479 1.938,0.417 10 false Central Gateway ECU (Network Gateway ECU) 0.844,0.26 1.302,0.469 0.458,0.208 10 false CA2H 0.865,0.865 1.323,1.073 0.458,0.208 10 false CA2L 1.333,0.25 1.583,0.448 0.25,0.198 10 false 22 1.344,0.646 1.594,0.844 0.25,0.198 10 false 7 2.156,0.656 2.406,0.854 0.25,0.198 10 false 9 2.156,0.25 2.406,0.448 0.25,0.198 10 false 3 1.958,2.875 2.271,3.073 0.313,0.198 10 false M31 1.969,3.052 3.188,3.417 1.219,0.365 10 false No. 6 CAN Junction Connector 0.198,2.865 0.51,3.063 0.313,0.198 10 false M35 0.198,3.063 1.427,3.448 1.229,0.385 10 false Parking Brake ECU Assembly 0.875,2.302 1.333,2.51 0.458,0.208 10 false CANH 0.875,2.698 1.333,2.906 0.458,0.208 10 false CANL 1.333,2.594 1.583,2.792 0.25,0.198 10 false 1 1.333,2.198 1.583,2.396 0.25,0.198 10 false 11 2.094,2.583 2.344,2.781 0.25,0.198 10 false 11 2.135,2.188 2.385,2.385 0.25,0.198 10 false 5 2.792,2.594 3.042,2.792 0.25,0.198 10 false 10 2.813,2.198 3.063,2.396 0.25,0.198 10 false 4 4.656,2.594 4.958,2.792 0.302,0.198 10 false 21 4.656,2.198 4.948,2.406 0.292,0.208 10 false 10 5.365,0.656 5.615,0.854 0.25,0.198 10 false 22 5.354,0.24 5.604,0.438 0.25,0.198 10 false 11 5.771,1.042 6.083,1.24 0.313,0.198 10 false G68 5.792,1.219 7.052,1.625 1.26,0.406 10 false Steering Sensor 6.042,0.76 6.531,0.958 0.49,0.198 10 false CANL 6.031,0.333 6.521,0.531 0.49,0.198 10 false CANH 5.854,0.229 6.104,0.427 0.25,0.198 10 false 3 5.865,0.635 6.115,0.833 0.25,0.198 10 false 8 4.469,2.865 4.875,3.073 0.406,0.208 10 false G96 4.51,3.052 5.75,3.385 1.24,0.333 10 false No. 1 CAN Junction Connector 5.385,2.594 5.698,2.792 0.313,0.198 10 false 20 5.396,2.198 5.708,2.396 0.313,0.198 10 false 9 4.552,4.073 4.865,4.271 0.313,0.198 10 false 4 4.531,4.479 4.844,4.677 0.313,0.198 10 false 10 4.552,5.833 4.865,6.031 0.313,0.198 10 false 11 4.563,5.427 4.875,5.625 0.313,0.198 10 false 5 5.708,5.448 6.021,5.646 0.313,0.198 10 false 10 3.865,5.448 4.177,5.646 0.313,0.198 10 false 1 5.969,5.552 6.458,5.75 0.49,0.198 10 false CANH 5.969,5.938 6.458,6.135 0.49,0.198 10 false CANL 5.177,6.125 5.667,6.323 0.49,0.198 10 false C54 5.167,6.292 7.156,6.719 1.99,0.427 10 false Rack and Pinion Power Steering Gear Assembly 1.833,5.021 2.875,5.448 1.042,0.427 10 false ECM 1.958,4.167 2.448,4.365 0.49,0.198 10 false CAN+ 1.969,4.552 2.458,4.75 0.49,0.198 10 false CAN- 3.865,4.073 4.177,4.271 0.313,0.198 10 false 6 3.813,4.479 4.125,4.677 0.313,0.198 10 false 12 4.531,7.052 4.885,7.25 0.354,0.198 10 false 2 4.531,7.458 4.844,7.656 0.313,0.198 10 false 8 6.052,7.042 6.542,7.24 0.49,0.198 10 false CANH 6.063,7.646 6.552,7.844 0.49,0.198 10 false CANL 5.583,7.719 6.073,7.917 0.49,0.198 10 false G70 5.594,7.917 7.156,8.323 1.563,0.406 10 false Airbag Sensor Assembly 3.583,7.698 4.073,7.896 0.49,0.198 10 false G104 3.583,7.896 4.833,8.323 1.25,0.427 10 false No. 4 CAN Junction Connector 5.729,7.052 6.031,7.271 0.302,0.219 10 false 26 5.74,7.427 6.021,7.625 0.281,0.198 10 false 27 1.302,6.292 3.479,6.729 2.177,0.438 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.323,6.083 1.813,6.281 0.49,0.198 10 false A42 1.948,5.51 2.438,5.708 0.49,0.198 10 false CA1H 1.969,5.906 2.458,6.104 0.49,0.198 10 false CA1L 2.448,5.833 2.76,6.031 0.313,0.198 10 false 38 3.875,5.833 4.188,6.031 0.313,0.198 10 false 7 1.521,4.906 2.01,5.104 0.49,0.198 10 false A24 2.448,5.438 2.771,5.635 0.323,0.198 10 false 37 5.708,5.854 6.063,6.052 0.354,0.198 10 false 11 2.448,4.073 2.76,4.271 0.313,0.198 10 false 7 2.438,4.49 2.75,4.688 0.313,0.198 10 false 17 2.823,0.656 3.073,0.854 0.25,0.198 10 false 8 2.813,0.25 3.167,0.448 0.354,0.198 10 false 2 3.646,0.354 4.104,0.563 0.458,0.208 10 false CANH 3.667,0.771 4.125,0.979 0.458,0.208 10 false CANL 3.417,0.25 3.667,0.448 0.25,0.198 10 false 5 3.417,0.656 3.667,0.854 0.25,0.198 10 false 4 3.25,0.979 3.563,1.177 0.313,0.198 10 false S21 3.25,1.156 4.479,1.542 1.229,0.385 10 false Occupant Detection ECU*1 0.208,8.479 2.615,8.865 2.406,0.385 10 false *1: w/ Occupant Classification System 1.073,8.052 3.438,8.385 2.365,0.333 10 false Hybrid Vehicle Control ECU Assembly 1.094,7.875 2.51,8.063 1.417,0.188 10 false A31*2, G64*3 1.99,7.156 2.479,7.354 0.49,0.198 10 false CA3P 1.979,7.563 2.469,7.76 0.49,0.198 10 false CA3N 3.865,7.052 4.219,7.25 0.354,0.198 10 false 3 3.885,7.448 4.198,7.646 0.313,0.198 10 false 9 2.469,7.052 2.781,7.25 0.313,0.198 10 false 7 2.448,7.469 2.76,7.667 0.313,0.198 10 false 20 3.042,8.51 4.094,8.865 1.052,0.354 10 false *2: for LHD 3.958,8.51 5.01,8.865 1.052,0.354 10 false *3: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.

C409618C11
0.396,1.208 0.823,1.469 0.427,0.26 4.063,1.313 4.49,1.573 0.427,0.26 2.906,1.406 2.677,0.552 2.677,0.552 2.427,0.552 true 2.906,1.75 2.719,2.25 2.719,2.25 2.469,2.25 true 3.104,1.448 2.958,0.354 2.958,0.354 2.708,0.354 true 3.073,1.698 2.917,2.448 2.917,2.448 2.667,2.448 true 3.219,1.688 3.25,2.5 3.25,2.5 3.417,2.5 true 3.302,1.417 3.438,0.833 3.438,0.833 3.604,0.833 true 5.458,1.229 5.417,0.917 5.417,0.917 5.25,0.917 true 0.604,0.208 0.917,0.406 0.313,0.198 10 false *a 3.906,0.188 4.219,0.385 0.313,0.198 10 false *e 1.865,0.469 2.479,0.667 0.615,0.198 10 false CANH*b 0.479,1.271 1.094,1.469 0.615,0.198 10 false G96 4.115,1.354 4.729,1.552 0.615,0.198 10 false G114 1.917,2.156 2.531,2.354 0.615,0.198 10 false CANL*b 2.156,0.26 2.771,0.458 0.615,0.198 10 false CANH*c 2.156,2.365 2.771,2.563 0.615,0.198 10 false CANL*c 3.677,0.76 4.292,0.958 0.615,0.198 10 false CANH*d 3.469,2.427 4.083,2.625 0.615,0.198 10 false CANL*d 4.927,0.854 5.542,1.052 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to No. 6 CAN Junction Connector *d to Steering Sensor
*e Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G96-9 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 CAN junction connector
G96-20 (CANL) - G114-4 (CG)
G96-10 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 6 CAN junction connector
G96-21 (CANL) - G114-4 (CG)
G96-11 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Steering sensor
G96-22 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)

C

4.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 6 CAN junction connector.


C409617C20
0.365,1.271 0.771,1.5 0.406,0.229 5.406,0.698 5.875,0.948 0.469,0.25 1.104,0.438 1.271,0.438 1.271,0.438 1.698,1.333 true 1.083,2.365 1.25,2.365 1.25,2.365 1.708,1.583 true 3.729,0.271 3.479,0.271 3.479,0.271 2.604,1.333 true 3.375,2.448 3.125,2.448 3.125,2.448 2.594,1.625 true 6.333,0.896 6.083,0.896 6.083,0.896 5.615,1.229 true 4.104,0.521 3.854,0.521 3.854,0.521 3.052,1.354 true 4.01,2.229 3.76,2.229 3.76,2.229 3.042,1.552 true 1.417,0.219 1.583,0.219 1.583,0.219 2.135,1.333 true 1.385,2.594 1.552,2.594 1.552,2.594 2.135,1.646 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.417,1.313 0.781,1.469 0.365,0.156 10 false M31 0.521,0.365 1.073,0.542 0.552,0.177 10 false CANH*b 0.5,2.271 1.052,2.448 0.552,0.177 10 false CANL*b 0.865,0.125 1.417,0.302 0.552,0.177 10 false CANH*c 0.833,2.51 1.385,2.688 0.552,0.177 10 false CANL*c 4.146,0.448 4.698,0.625 0.552,0.177 10 false CANH*e 4.083,2.156 4.635,2.333 0.552,0.177 10 false CANL*e 5.469,0.75 5.927,0.969 0.458,0.219 10 false G114 6.406,0.823 6.823,1.01 0.417,0.188 10 false CG 4.792,0.583 5.104,0.781 0.313,0.198 10 false *f 3.802,0.188 4.354,0.365 0.552,0.177 10 false CANH*d 3.458,2.375 4.01,2.552 0.552,0.177 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Occupant Detection ECU (w/ Occupant Classification System)
*c to Central Gateway ECU (Network Gateway ECU) *d to No. 1 CAN Junction Connector
*e to Parking Brake ECU Assembly *f Front view of DLC3


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*: w/ Occupant Classification System

M31-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Occupant detection ECU*
M31-8 (CANL) - G114-4 (CG)
M31-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
M31-9 (CANL) - G114-4 (CG)
M31-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
M31-10 (CANL) - G114-4 (CG)
M31-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Parking brake ECU assembly
M31-11 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

3.CHECK SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
3.CHECK SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the M31 No. 6 CAN junction connector.


b.
C406353C58
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.729,2.104 2.531,2.104 2.531,2.104 2.313,1.521 true 1.646,3.146 1.25,2.75 1.25,2.75 1.083,2.75 true 2.75,0.667 2.552,0.667 2.552,0.667 2.417,1.24 true 1.563,0.292 2.177,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 2.813,0.594 3.302,0.781 0.49,0.188 10 false CA2L 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.792,2.031 3.24,2.24 0.448,0.208 10 false CA2H 0.771,2.688 1.385,2.885 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-22 (CA2H) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G72-7 (CA2L) - G114-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

4.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.

C409617C22
0.365,1.271 0.771,1.5 0.406,0.229 5.406,0.698 5.875,0.948 0.469,0.25 0.729,0.656 0.896,0.656 0.896,0.656 1.677,1.344 true 0.813,2.083 0.979,2.083 0.979,2.083 1.708,1.594 true 1.469,0.458 1.635,0.458 1.635,0.458 2.167,1.323 true 1.385,2.438 1.552,2.438 1.552,2.438 2.146,1.625 true 3.729,0.271 3.479,0.271 3.479,0.271 2.583,1.323 true 3.375,2.448 3.125,2.448 3.125,2.448 2.573,1.646 true 6.156,0.906 5.99,0.906 5.99,0.906 5.625,1.229 true 4.083,0.5 3.917,0.5 3.917,0.5 3.042,1.302 true 3.792,2.135 3.542,2.135 3.542,2.135 3.052,1.635 true 0.729,0.948 0.896,0.948 0.896,0.948 1.25,1.354 true 0.771,1.875 0.938,1.875 0.938,1.875 1.24,1.594 true 4.01,1.021 3.844,1.021 3.844,1.021 3.49,1.323 true 3.917,1.813 3.75,1.813 3.75,1.813 3.5,1.635 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.417,1.313 0.781,1.469 0.365,0.156 10 false G104 0.156,0.594 0.708,0.771 0.552,0.177 10 false CANH*c 0.26,2 0.813,2.177 0.552,0.177 10 false CANL*c 0.885,0.385 1.438,0.563 0.552,0.177 10 false CANH*d 0.844,2.354 1.396,2.531 0.552,0.177 10 false CANL*d 3.792,0.198 4.344,0.375 0.552,0.177 10 false CANH*e 3.438,2.385 3.99,2.563 0.552,0.177 10 false CANL*e 5.469,0.75 5.927,0.969 0.458,0.219 10 false G114 6.271,0.823 6.688,1.01 0.417,0.188 10 false CG 4.865,0.656 5.177,0.854 0.313,0.198 10 false *h 4.188,0.438 4.74,0.615 0.552,0.177 10 false CANH*f 3.865,2.063 4.417,2.24 0.552,0.177 10 false CANL*f 0.146,0.885 0.698,1.063 0.552,0.177 10 false CANH*b 0.219,1.802 0.771,1.979 0.552,0.177 10 false CANL*b 4.094,0.969 4.646,1.146 0.552,0.177 10 false CANH*g 4,1.76 4.552,1.938 0.552,0.177 10 false CANL*g
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*c to Airbag Sensor Assembly *d to Hybrid Vehicle Control ECU Assembly
*e to No. 1 CAN Junction Connector *f to Rack and Pinion Power Steering Gear Assembly
*g to ECM *h Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G104-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (skid control ECU)
G104-7 (CANL) - G114-4 (CG)
G104-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
G104-8 (CANL) - G114-4 (CG)
G104-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU assembly
G104-9 (CANL) - G114-4 (CG)
G104-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
G104-10 (CANL) - G114-4 (CG)
G104-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Rack and pinion power steering gear assembly
G104-11 (CANL) - G114-4 (CG)
G104-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
G104-12 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect the CAN junction connector.


b.
C406381C40
1.5,0.083 1.917,0.333 0.417,0.25 0.417,2.583 0.833,2.833 0.417,0.25 1.323,0.896 1.24,1.427 1.24,1.427 1.073,1.427 true 1.104,0.323 1.271,0.323 1.271,0.323 1.323,0.781 true 1.052,2.198 1.219,2.198 1.219,2.198 1.635,2.563 true 0.469,2.625 0.927,2.823 0.458,0.198 10 false G114 0.729,0.25 1.188,0.448 0.458,0.198 10 false CA2L 1.583,0.135 2.042,0.333 0.458,0.198 10 false G72 0.677,1.344 1.135,1.542 0.458,0.198 10 false CA2H 0.76,2.135 1.219,2.333 0.458,0.198 10 false CG 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.135,2.115 0.594,2.313 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-22 (CA2H) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G72-7 (CA2L) - G114-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPAIR ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR