Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area

*1: w/ Memory

*2: w/ Power Back Door System

There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main bus wire

·

Short to GND in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH

·

Position control ECU assembly*1

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

·

Air conditioning amplifier assembly

·

Multiplex network door ECU*2

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 5 CAN junction connector

·

No. 7 CAN junction connector



WIRING DIAGRAM

C405908E01
0.833,2.094 1.448,2.292 0.615,0.198 10 false CANP 0.823,2.49 1.438,2.688 0.615,0.198 10 false CANN 0.833,3.729 1.448,3.927 0.615,0.198 10 false CANH 0.833,4.125 1.448,4.323 0.615,0.198 10 false CANL 0.823,5.333 1.438,5.531 0.615,0.198 10 false CANP 0.823,5.74 1.438,5.938 0.615,0.198 10 false CANN 5.896,4.083 6.51,4.281 0.615,0.198 10 false CANL 5.906,3.698 6.521,3.896 0.615,0.198 10 false CANH 5.927,2.51 6.542,2.708 0.615,0.198 10 false CANL 5.927,2.104 6.542,2.302 0.615,0.198 10 false CANH 5.917,0.479 6.531,0.677 0.615,0.198 10 false CANH 5.927,0.896 6.542,1.094 0.615,0.198 10 false CANL 0.75,0.385 1.365,0.583 0.615,0.198 10 false CANH 0.75,0.969 1.365,1.167 0.615,0.198 10 false CANL 0.188,1.042 0.802,1.24 0.615,0.198 10 false G18 0.177,2.635 0.792,2.833 0.615,0.198 10 false R18 0.219,4.292 0.833,4.49 0.615,0.198 10 false A11 0.281,5.906 0.896,6.104 0.615,0.198 10 false T8 0.198,1.219 2,1.615 1.802,0.396 10 false Combination Meter Assembly 0.177,2.823 2.146,3.042 1.969,0.219 10 false Multiplex Network Door ECU*2 0.208,4.469 2.375,4.771 2.167,0.302 10 false Headlight ECU Sub-assembly LH 0.25,6.083 1.583,6.5 1.333,0.417 10 false Position Control ECU Assembly*1 5.5,1.021 6.115,1.219 0.615,0.198 10 false G46 5.427,2.656 6.042,2.854 0.615,0.198 10 false G44 5.469,4.24 6.083,4.438 0.615,0.198 10 false G54 5.5,1.219 7.052,1.719 1.552,0.5 10 false Air Conditioning Amplifier Assembly 5.427,2.844 7.052,3.313 1.625,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,4.427 6.99,4.885 1.5,0.458 10 false Certification ECU (Smart Key ECU Assembly) 2.135,6.333 3.354,6.75 1.219,0.417 10 false No. 7 CAN Junction Connector 3.698,6.344 4.917,6.76 1.219,0.417 10 false No. 1 CAN Junction Connector 2.146,6.115 2.76,6.313 0.615,0.198 10 false N52 3.667,6.125 4.281,6.323 0.615,0.198 10 false G96 1.354,0.365 1.969,0.563 0.615,0.198 10 false 9 1.344,0.781 1.958,0.979 0.615,0.198 10 false 25 1.344,2.01 1.958,2.208 0.615,0.198 10 false 39 1.354,2.406 1.969,2.604 0.615,0.198 10 false 40 1.344,3.646 1.958,3.844 0.615,0.198 10 false 24 1.354,4.01 1.969,4.208 0.615,0.198 10 false 23 1.333,5.271 1.948,5.469 0.615,0.198 10 false 13 1.333,5.667 1.948,5.865 0.615,0.198 10 false 14 2.479,5.667 3.094,5.865 0.615,0.198 10 false 10 2.531,5.271 3.146,5.469 0.615,0.198 10 false 4 2.479,4.042 3.094,4.24 0.615,0.198 10 false 11 2.542,3.625 3.156,3.823 0.615,0.198 10 false 5 2.542,2.406 3.156,2.604 0.615,0.198 10 false 9 2.542,2 3.156,2.198 0.615,0.198 10 false 3 2.531,0.792 3.146,0.99 0.615,0.198 10 false 8 2.531,0.385 3.146,0.583 0.615,0.198 10 false 2 4.51,0.365 5.125,0.563 0.615,0.198 10 false 5 5.719,0.385 6.333,0.583 0.615,0.198 10 false 2 5.719,0.792 6.333,0.99 0.615,0.198 10 false 1 4.479,0.781 5.094,0.979 0.615,0.198 10 false 16 4.5,2 5.115,2.198 0.615,0.198 10 false 4 4.479,2.406 5.094,2.604 0.615,0.198 10 false 15 5.719,2.01 6.333,2.208 0.615,0.198 10 false 5 5.719,2.417 6.333,2.615 0.615,0.198 10 false 4 5.719,3.604 6.333,3.802 0.615,0.198 10 false 1 5.729,4 6.344,4.198 0.615,0.198 10 false 2 4.51,3.573 5.125,3.771 0.615,0.198 10 false 2 4.49,4.021 5.104,4.219 0.615,0.198 10 false 13 3.26,1.979 3.875,2.177 0.615,0.198 10 false 1 3.26,2.396 3.875,2.594 0.615,0.198 10 false 7 3.76,1.99 4.375,2.188 0.615,0.198 10 false 1 3.688,2.396 4.302,2.594 0.615,0.198 10 false 12 4.5,5.229 5.115,5.427 0.615,0.198 10 false 3 4.5,5.625 5.115,5.823 0.615,0.198 10 false 14 0.25,7.01 2.417,7.313 2.167,0.302 10 false *1: for LHD with Memory 0.25,7.427 2.417,7.729 2.167,0.302 10 false *2: w/ Power Back Door System


C405909E01
1.458,0.417 2.073,0.615 0.615,0.198 10 false CANH 1.49,0.781 2.104,0.979 0.615,0.198 10 false CANL 1.49,2.031 2.104,2.229 0.615,0.198 10 false CANP 1.49,2.417 2.104,2.615 0.615,0.198 10 false CANN 5.365,1.927 5.979,2.125 0.615,0.198 10 false CA5H 5.365,2.531 5.979,2.729 0.615,0.198 10 false CA5L 0.833,0.938 1.448,1.135 0.615,0.198 10 false A12 0.854,2.594 1.469,2.792 0.615,0.198 10 false S8 4.917,2.604 5.531,2.802 0.615,0.198 10 false G72 0.833,1.135 3.042,1.333 2.208,0.198 10 false Headlight ECU Sub-assembly RH 0.833,2.781 2.26,3.125 1.427,0.344 10 false Position Control ECU Assembly* 4.917,2.792 6.885,3.156 1.969,0.365 10 false Central Gateway ECU (Network Gateway ECU) 1.99,0.313 2.604,0.51 0.615,0.198 10 false 24 1.979,0.677 2.594,0.875 0.615,0.198 10 false 23 3.083,0.313 3.698,0.51 0.615,0.198 10 false 10 3.104,0.698 3.719,0.896 0.615,0.198 10 false 21 3.927,0.292 4.542,0.49 0.615,0.198 10 false 9 3.927,0.719 4.542,0.917 0.615,0.198 10 false 20 3.917,1.906 4.531,2.104 0.615,0.198 10 false 11 5.042,1.917 5.656,2.115 0.615,0.198 10 false 15 5.042,2.302 5.656,2.5 0.615,0.198 10 false 16 3.927,2.333 4.542,2.531 0.615,0.198 10 false 22 3.094,2.313 3.708,2.51 0.615,0.198 10 false 19 3.135,1.906 3.75,2.104 0.615,0.198 10 false 8 1.958,1.917 2.573,2.115 0.615,0.198 10 false 13 1.969,2.323 2.583,2.521 0.615,0.198 10 false 14 0.292,3.406 2.5,3.604 2.208,0.198 10 false *: for RHD with Memory 2.792,2.708 3.406,2.906 0.615,0.198 10 false G105 2.802,2.865 4.021,3.25 1.219,0.385 10 false No. 5 CAN Junction Connector


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.

C409618C13
0.625,1.24 1.031,1.49 0.406,0.25 5.302,0.74 5.76,1.01 0.458,0.271 1.281,0.594 1.531,0.594 1.531,0.594 1.531,1.375 true 1.281,2.135 1.531,2.135 1.531,2.135 1.531,1.719 true 1.438,0.385 1.688,0.385 1.688,0.385 1.688,1.385 true 1.438,2.365 1.688,2.365 1.688,2.365 1.688,1.698 true 2.219,0.365 2.052,0.365 2.052,0.365 2.052,1.365 true 2.208,2.385 2.042,2.385 2.042,2.385 2.042,1.719 true 1.625,0.177 1.875,0.177 1.875,0.177 1.875,1.375 true 1.688,2.573 1.854,2.573 1.854,2.573 1.854,1.74 true 2.375,0.542 2.208,0.542 2.208,0.542 2.208,1.375 true 2.385,2.219 2.219,2.219 2.219,2.219 2.219,1.719 true 5,0.979 5.167,0.979 5.167,0.979 5.417,1.26 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.719,1.292 1.219,1.531 0.5,0.24 10 false G96 0.74,0.521 1.406,0.76 0.667,0.24 10 false CANH*b 0.76,2.052 1.427,2.292 0.667,0.24 10 false CANL*b 0.885,0.292 1.552,0.531 0.667,0.24 10 false CANH*c 0.917,2.292 1.583,2.531 0.667,0.24 10 false CANL*c 2.271,0.292 2.938,0.531 0.667,0.24 10 false CANH*e 2.25,2.313 2.917,2.552 0.667,0.24 10 false CANL*e 1.063,0.094 1.729,0.333 0.667,0.24 10 false CANH*d 1.167,2.49 1.833,2.729 0.667,0.24 10 false CANL*d 2.427,0.469 3.094,0.708 0.667,0.24 10 false CANH*f 2.427,2.146 3.094,2.385 0.667,0.24 10 false CANL*f 5.354,0.781 5.854,1.021 0.5,0.24 10 false G114 4.74,0.896 5.406,1.135 0.667,0.24 10 false CG 4.688,0.521 5.354,0.76 0.667,0.24 10 false *g
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 7 CAN Junction Connector
*c to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *d to No. 5 CAN Junction Connector
*e to Main Body ECU (Multiplex Network Body ECU) *f to Air Conditioning Amplifier Assembly
*g Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G96-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 7 CAN junction connector
G96-12 (CANL) - G114-4 (CG)
G96-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)
G96-13 (CANL) - G114-4 (CG)
G96-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 5 CAN junction connector
G96-14 (CANL) - G114-4 (CG)
G96-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
G96-15 (CANL) - G114-4 (CG)
G96-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
G96-16 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 5 CAN junction connector CAN main wire) B
NG (No. 7 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 5 CAN junction connector.

C409618C12
0.625,1.24 1.031,1.49 0.406,0.25 5.302,0.74 5.76,1.01 0.458,0.271 2.49,0.594 2.74,0.594 2.74,0.594 2.74,1.375 true 2.49,2.156 2.74,2.156 2.74,2.156 2.74,1.74 true 2.656,0.375 2.906,0.375 2.906,0.375 2.906,1.375 true 2.667,2.396 2.917,2.396 2.917,2.396 2.917,1.729 true 2.833,0.177 3.083,0.177 3.083,0.177 3.083,1.375 true 2.906,2.583 3.073,2.583 3.073,2.583 3.073,1.75 true 3.49,0.385 3.271,0.385 3.271,0.385 3.271,1.385 true 3.458,2.583 3.25,2.583 3.25,2.583 3.25,1.75 true 5.042,0.927 5.208,0.927 5.208,0.927 5.427,1.25 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.677,1.292 1.177,1.531 0.5,0.24 10 false G105 1.917,0.51 2.583,0.75 0.667,0.24 10 false CANH*b 1.979,2.063 2.646,2.302 0.667,0.24 10 false CANL*b 2.104,0.292 2.771,0.531 0.667,0.24 10 false CANH*c 2.125,2.313 2.792,2.552 0.667,0.24 10 false CANL*c 2.26,0.094 2.927,0.333 0.667,0.24 10 false CANH*d 2.323,2.51 2.99,2.75 0.667,0.24 10 false CANL*d 5.354,0.781 5.854,1.021 0.5,0.24 10 false G114 4.771,0.844 5.438,1.083 0.667,0.24 10 false CG 4.708,0.552 5.375,0.792 0.667,0.24 10 false *f 3.531,0.333 4.198,0.573 0.667,0.24 10 false CANH*e 3.521,2.521 4.188,2.76 0.667,0.24 10 false CANL*e
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Position Control ECU Assembly (for RHD with Memory)
*c to No. 1 CAN Junction Connector *d to Headlight ECU Sub-assembly RH
*e to Central Gateway ECU (Network Gateway ECU) *f Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*: for RHD with Memory

G105-8 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Position control ECU assembly*
G105-19 (CANL) - G114-4 (CG)
G105-9 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
G105-20 (CANL) - G114-4 (CG)
G105-10 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Headlight ECU sub-assembly RH
G105-21 (CANL) - G114-4 (CG)
G105-11 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G105-22 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the G105 No. 5 CAN junction connector.


b.
C406353C59
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 1.375,1.5 1.146,2.229 1.146,2.229 0.979,2.229 true 1.844,2.167 1.677,2.167 1.677,2.167 1.521,1.51 true 1.625,3.125 1.26,2.802 1.26,2.802 1.094,2.802 true 1.573,0.292 2.188,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 0.594,2.146 1.208,2.344 0.615,0.198 10 false CA5H 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 1.917,2.104 2.531,2.302 0.615,0.198 10 false CA5L 0.781,2.729 1.396,2.927 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-15 (CA5H) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G72-16 (CA5L) - G114-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 7 CAN junction connector.

C409617C14
0.365,1.271 0.771,1.5 0.406,0.229 5.406,0.698 5.875,0.948 0.469,0.25 0.729,0.656 0.896,0.656 0.896,0.656 1.26,1.365 true 0.813,2.083 0.979,2.083 0.979,2.083 1.26,1.583 true 1.104,0.438 1.271,0.438 1.271,0.438 1.698,1.333 true 1.083,2.365 1.25,2.365 1.25,2.365 1.708,1.583 true 3.729,0.271 3.479,0.271 3.479,0.271 2.604,1.333 true 3.375,2.448 3.125,2.448 3.125,2.448 2.594,1.625 true 4.104,0.521 3.854,0.521 3.854,0.521 3.052,1.354 true 4.01,2.229 3.76,2.229 3.76,2.229 3.042,1.552 true 1.417,0.219 1.583,0.219 1.583,0.219 2.135,1.333 true 1.385,2.594 1.552,2.594 1.552,2.594 2.135,1.646 true 5.125,0.948 5.292,0.948 5.292,0.948 5.583,1.219 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.417,1.313 0.781,1.469 0.365,0.156 10 false N52 0.156,0.594 0.708,0.771 0.552,0.177 10 false CANH*b 0.26,2 0.813,2.177 0.552,0.177 10 false CANL*b 0.542,0.344 1.094,0.521 0.552,0.177 10 false CANH*c 0.552,2.292 1.104,2.469 0.552,0.177 10 false CANL*c 3.792,0.198 4.344,0.375 0.552,0.177 10 false CANH*e 3.438,2.385 3.99,2.563 0.552,0.177 10 false CANL*e 5.469,0.75 5.927,0.969 0.458,0.219 10 false G114 4.865,0.865 5.281,1.052 0.417,0.188 10 false CG 4.792,0.583 5.104,0.781 0.313,0.198 10 false *g 4.177,0.448 4.729,0.625 0.552,0.177 10 false CANH*f 4.073,2.156 4.625,2.333 0.552,0.177 10 false CANL*f 0.844,0.125 1.396,0.302 0.552,0.177 10 false CANH*d 0.865,2.51 1.417,2.688 0.552,0.177 10 false CANL*d
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to Combination Meter Assembly *d to Multiplex Network Door ECU (w/ Power Back Door System)
*e to Position Control ECU Assembly (for LHD with Memory) *f to Headlight ECU Sub-assembly LH
*g Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Power Back Door System

*2: for LHD with Memory

N52-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
N52-7 (CANL) - G114-4 (CG)
N52-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter assembly
N52-8 (CANL) - G114-4 (CG)
N52-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Multiplex network door ECU*1
N52-9 (CANL) - G114-4 (CG)
N52-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Position control ECU assembly*2
N52-10 (CANL) - G114-4 (CG)
N52-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Headlight ECU sub-assembly LH
N52-11 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.
C406370C15
1.448,0.25 1.917,0.51 0.469,0.26 1.427,2.365 1.896,2.625 0.469,0.26 1.844,1.125 1.51,1.875 1.51,1.875 1.344,1.875 true 1.615,3.063 1.198,2.708 1.198,2.708 1.031,2.708 true 1.938,1.135 1.969,1.875 1.969,1.875 2.135,1.875 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.115,2.198 0.427,2.396 0.313,0.198 10 false *b 1.563,0.302 2.052,0.552 0.49,0.25 10 false G72 1.5,2.417 1.99,2.667 0.49,0.25 10 false G114 2.177,1.802 2.667,2.052 0.49,0.25 10 false CA5H 0.969,1.813 1.458,2.063 0.49,0.25 10 false CA5L 0.74,2.635 1.229,2.885 0.49,0.25 10 false CG
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus wire shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-15 (CA5H) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G72-16 (CA5L) - G114-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR