The certification ECU (smart key ECU assembly) has a power source mode switching function.
This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.
The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2782 | Power Source Control ECU Malfunction | Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the power switch is on (IG).)):
·
The steering lock motor activation command circuit has a short circuit. ·
The steering lock motor activation command circuit has an open circuit.
|
·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Certification ECU (Smart key ECU assembly) ·
Harness or connector |
DTC Output Confirmation Operation:
·
Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift state park (P) and the power switch off. The steering unlocks when the power switch is turned on (ACC) or on (IG) while carrying the key.) |
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. | Prohibits the hybrid control system from being started. |
| DTC No. | Data List and Active Test |
|---|---|
| B2782 | - |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
| *b | Waveform |
| *c | Steering Lock Motor not Operating |
| *d | Steering Lock Motor Operating |
Using an oscilloscope, check the waveform.
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| G56-3 (IGE) - G56-1 (GND) | 2 V/DIV., 200 ms./DIV. | Any door opened when following conditions are met, and then steering lock motor activated:
·
Shift state park (P) ·
Steering lock unlocked in advance by carrying key and turning power switch on (IG) ·
After above conditions are met, power switch turned off |
Pulse generation
(See waveform) |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).
To lock the steering, turn the power switch off with the shift state park (P), and then open a door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.
Clear the DTCs.
Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform the DTC output confirmation operation.
Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.
Check if DTC B2782 is output.
| Result | Proceed to |
|---|---|
| DTC B2782 is not output. | A |
| DTC B2782 is output. | B |
A
B
Disconnect the G56 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the G54 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-3 (IGE) - G54-25 (SLR+) | Always | Below 1 Ω |
| G56-1 (GND) - Body ground | Always | Below 1 Ω |
| G56-3 (IGE) or G54-25 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
If the result is not as specified, check for looseness in the connection which leads to ground.
| Proceed to |
|---|
| OK |
| NG |
OK
NG