A thermistor, whose resistance changes in accordance with the engine oil temperature, is built into the engine oil temperature sensor (engine oil pressure and temperature sensor). As the engine oil temperature decreases, the thermistor resistance increases and as the engine oil temperature increases, the thermistor resistance decreases. The engine oil temperature sensor (engine oil pressure and temperature sensor) is connected to the ECM. A voltage of 5 V is supplied from terminal THEO via resistor R of the ECM. Since resistor R and the engine oil temperature sensor (engine oil pressure and temperature sensor) are connected in series, both the resistance and the electrical potential of THEO are subject to change in accordance with a change in the engine oil temperature.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P019511 | Engine Oil Temperature Sensor Circuit Short to Ground | The engine oil temperature sensor (engine oil pressure and temperature sensor) output voltage is less than 0.535 V for 5 seconds or more (1 trip detection logic). | ·
Short in engine oil temperature sensor (engine oil pressure and temperature sensor) circuit ·
Engine oil temperature sensor ·
ECM |
Comes on | DTC stored | SAE Code: P0197 |
When this DTC is output, check the engine oil temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.
| DTC No. | Engine Oil Temperature Sensor | Malfunction |
|---|---|---|
| P019511 | -40°C (-40°F) | ·
Short to ground in THEO circuit ·
Short in EPEO to THEO circuit ·
Open in VCPE circuit |
If the Data List values are normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM monitors the engine oil temperature sensor (engine oil pressure and temperature sensor) and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor (engine oil pressure and temperature sensor) output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor (engine oil pressure and temperature sensor) circuit is malfunctioning and stores this DTC.
Example:
If the engine oil temperature sensor (engine oil pressure and temperature sensor) output voltage is less than 0.535 V for 5 seconds or more, the ECM will store this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Wait 10 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P019511.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Engine Oil Temperature Sensor (Engine Oil Pressure and Temperature Sensor)) |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the engine oil temperature sensor (engine oil pressure and temperature sensor) connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C5-3 (VC) - C5-2 (GND) | Engine switch on (IG) | 4.5 to 5.5 V |
| C5-4 (TOUT) - C5-2 (GND) | Engine switch on (IG) | 3.0 to 5.5 V |
Turn the engine switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C5-3 (VC) - C5-4 (TOUT) | Engine switch off | 171 to 189 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine oil temperature sensor (engine oil pressure and temperature sensor) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-3 (VC) - C40-99 (VCPE) | Always | Below 1 Ω |
| C5-4 (TOUT) or C40-123 (THEO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG