Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0374955 HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY)  P1C8679  Transmission (Input) Mechanical Linkage Failure  


DESCRIPTION

Refer to the description for DTC P1C7779.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>P1C7779

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C8679 Transmission (Input) Mechanical Linkage Failure Hybrid vehicle transaxle malfunction (input system lock):
When the vehicle is stopped, an engine cranking signal is sent but the generator (MG1) does not rotate.
The generator (MG1) or the engine does not rotate, or the planetary gear unit is malfunctioning.
(1 trip detection logic)
·

Hybrid vehicle transaxle assembly

·

Transmission input damper assembly

·

Engine


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1C8679
·

Generator Revolution

·

Motor Revolution

·

Engine Speed



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With the vehicle stopped and the shift lever in P, turn the power switch on (READY) and gradually depress the accelerator pedal so that the engine starts.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

HINT:
·

Engine lock or a mechanical malfunction has occurred inside the hybrid vehicle transaxle assembly.

·

If this DTC is output, the engine or gears in the transaxle may have seized. Before performing this inspection, check the engine oil, hybrid transaxle fluid, coolant (for Engine) and coolant (for Inverter) levels.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Check for DTCs.

Result:
Result Proceed to
P1C8679 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1C8779 Generator Mechanical Linkage Failure
P1C8879 Planetary Gear Mechanical Linkage Failure

HINT:

P1C8679 may be output as a result of the malfunction indicated by the DTCs above.



e.

Turn the power switch off.



A

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

B

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

OK

3.CLEAR DTC

NG

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
4.CHECK ENGINE RACING

OK

5.CHECK CREEP MOVEMENT

NG

5.CHECK CREEP MOVEMENT

OK

6.INSPECT ENGINE SPEED

NG

6.INSPECT ENGINE SPEED

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>P1C7779

Result:
Result Proceed to
The absolute value of the difference is less than 500 rpm. A
The absolute value of the difference is 500 rpm or more continuously for 1 second. B



A

B

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)

OK

NG

REPAIR OR REPLACE ENGINE