Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076382 A25A-FKS ENGINE CONTROL _0379392 SFI SYSTEM(w/ Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump (for low pressure side) circuit consists of the ECM, fuel pump (for low pressure side) and fuel pump control ECU (which operates the fuel pump (for low pressure side)). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU. Based on the signal sent from the ECM, the fuel pump control ECU adjusts the fuel pump (for low pressure side) operation speed.

WIRING DIAGRAM

A444315E03
6.073,0.552 6.625,0.833 0.552,0.281 10 false MREL 5.813,0.531 6.115,0.823 0.302,0.292 10 false 15 2.042,0.542 2.271,0.844 0.229,0.302 10 false 1 2.823,0.531 2.979,0.729 0.156,0.198 10 false 2 2.823,1.135 2.979,1.333 0.156,0.198 10 false 5 2.042,1.135 2.198,1.333 0.156,0.198 10 false 3 2.052,1.646 3.385,1.969 1.333,0.323 10 false EFI-MAIN NO. 1 0.667,1.479 1.823,1.76 1.156,0.281 10 false EFI-MAIN NO. 1 1.615,2.75 2.771,3.042 1.156,0.292 10 false EFI-MAIN NO. 2 4.563,2.021 4.719,2.219 0.156,0.198 10 false 2 5.344,2.021 5.5,2.219 0.156,0.198 10 false 1 4.563,2.5 4.719,2.698 0.156,0.198 10 false 3 5.344,2.479 5.5,2.677 0.156,0.198 10 false 5 4.49,2.948 5.688,3.26 1.198,0.313 10 false EFI-MAIN NO. 2 0.563,5.26 1.125,5.677 0.563,0.417 10 false Auxiliary Battery 0.969,6.042 1.427,6.24 0.458,0.198 10 false N26 0.979,6.208 2.219,6.688 1.24,0.479 10 false Fuel Pump (for Low Pressure Side) 1.531,3.906 2.146,4.104 0.615,0.198 10 false BLPU 1.99,3.792 2.146,3.99 0.156,0.198 10 false 3 1.521,4.458 2.135,4.656 0.615,0.198 10 false BLPV 1.979,4.344 2.135,4.542 0.156,0.198 10 false 4 1.51,4.99 2.125,5.188 0.615,0.198 10 false BLPW 1.979,4.885 2.135,5.083 0.156,0.198 10 false 2 1.552,5.521 2.167,5.719 0.615,0.198 10 false BLPE 1.979,5.396 2.135,5.594 0.156,0.198 10 false 1 2.333,5.667 3.063,5.979 0.729,0.313 10 false Shielded 3.01,3.927 3.469,4.125 0.458,0.198 10 false N14 3.083,3.74 3.24,3.938 0.156,0.198 10 false 2 3.323,3.906 3.781,4.104 0.458,0.198 10 false FPU 3.083,4.281 3.24,4.479 0.156,0.198 10 false 3 3.323,4.448 3.781,4.646 0.458,0.198 10 false FPV 3.073,4.802 3.229,5 0.156,0.198 10 false 4 3.073,5.344 3.229,5.542 0.156,0.198 10 false 1 3.333,5.51 3.792,5.708 0.458,0.198 10 false FPG 3.333,4.979 3.792,5.177 0.458,0.198 10 false FPW 4.813,4.146 5.271,4.344 0.458,0.198 10 false N15 4.875,3.938 5.031,4.135 0.156,0.198 10 false 1 4.552,4.115 4.865,4.313 0.313,0.198 10 false +B 4.823,4.708 5.281,4.906 0.458,0.198 10 false N15 4.885,4.5 5.042,4.698 0.156,0.198 10 false 2 4.427,4.729 4.875,4.99 0.448,0.26 10 false FPC 4.823,5.563 5.281,5.76 0.458,0.198 10 false N15 4.875,5.375 5.031,5.573 0.156,0.198 10 false 3 4.438,5.542 4.896,5.74 0.458,0.198 10 false GND 3.292,6.063 4.958,6.417 1.667,0.354 10 false Fuel Pump Control ECU 5.885,4.573 6.042,4.771 0.156,0.198 10 false 6 6.073,4.573 6.531,4.771 0.458,0.198 10 false FPC 6.323,6.063 6.75,6.344 0.427,0.281 10 false A24 6.333,6.208 6.75,6.521 0.417,0.313 10 false ECM 6.635,0.635 6.844,0.833 0.208,0.198 10 false IC 3.01,4.469 3.469,4.667 0.458,0.198 10 false N14 3.01,5 3.469,5.198 0.458,0.198 10 false N14 3.01,5.531 3.469,5.729 0.458,0.198 10 false N14

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT FUEL PUMP CONTROL ECU
A426034C03
2.5,0.25 2.917,0.5 0.417,0.25 4.083,0.25 4.5,0.5 0.417,0.25 1.865,2.302 2.344,1.458 false 2.375,2.313 2.625,1.469 false 2.854,2.313 2.906,1.469 false 3.354,2.313 3.135,1.479 false 3.958,2.302 4.021,1.354 false 4.448,2.313 4.292,1.365 false 5.052,2.323 4.563,1.354 false 0.25,0.125 0.563,0.281 0.313,0.156 10 false *1 2.573,0.292 3.042,0.521 0.469,0.229 10 false N14 4.156,0.281 4.625,0.51 0.469,0.229 10 false N15 1.667,2.365 2.135,2.594 0.469,0.229 10 false FPW 2.219,2.375 2.688,2.604 0.469,0.229 10 false FPV 2.75,2.375 3.219,2.604 0.469,0.229 10 false FPU 3.25,2.375 3.719,2.604 0.469,0.229 10 false FPG 3.823,2.375 4.292,2.604 0.469,0.229 10 false GND 4.354,2.385 4.823,2.615 0.469,0.229 10 false FPC 4.99,2.385 5.458,2.615 0.469,0.229 10 false +B
*1 Fuel Pump Control ECU - -


a.

Remove the fuel pump control ECU.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL PUMP ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N15-1 (+B) - N15-3 (GND) Always 10 Ω or higher
N15-1 (+B) - N15-2 (FPC) Always 2 kΩ or higher
N15-2 (FPC) - N15-3 (GND) Always 1 kΩ or higher
N14-1 (FPG) - N15-3 (GND) Always Below 1 kΩ
N14-2 (FPU) - N15-3 (GND) Always 2 kΩ or higher
N14-3 (FPV) - N15-3 (GND) Always 2 kΩ or higher
N14-4 (FPW) - N15-3 (GND) Always 2 kΩ or higher


HINT:

This procedure checks for an internal short of the fuel pump control ECU when its transistor is stuck on.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)

NG

REPLACE FUEL PUMP CONTROL ECU

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)
A428848C19
0.5,1.083 0.917,1.333 0.417,0.25 1.083,1.708 1.417,1.333 false 2.26,1.729 1.969,1.344 false 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 0.563,1.125 1.01,1.344 0.448,0.219 10 false N15 0.979,1.729 1.427,1.948 0.448,0.219 10 false +B 2.177,1.771 2.625,1.99 0.448,0.219 10 false GND
*a Front view of wire harness connector
(to Fuel Pump Control ECU)


a.

Disconnect the fuel pump control ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N15-1 (+B) - N15-3 (GND) Engine switch on (IG) 11 to 14 V


HINT:

Make a note of the measured voltage as it may be used in a following Active Test.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N15-2 (FPC) - A24-6 (FPC) Always Below 1 Ω
N15-2 (FPC) or A24-6 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
A426033C03
2.5,0.25 2.917,0.5 0.417,0.25 2.073,2.302 2.365,1.458 false 2.688,2.281 2.615,1.469 false 3.302,2.323 2.885,1.469 false 0.156,0.125 0.469,0.281 0.313,0.156 10 false *1 2.583,0.292 3.021,0.5 0.438,0.208 10 false N14 1.906,2.365 2.344,2.573 0.438,0.208 10 false FPW 2.583,2.365 3.021,2.573 0.438,0.208 10 false FPV 3.208,2.365 3.646,2.573 0.438,0.208 10 false FPU
*1 Fuel Pump Control ECU - -


a.

Disconnect the N14 fuel pump control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
N14-2 (FPU) - Body ground U Phase 4.4 to 8.4 V*
N14-3 (FPV) - Body ground V Phase 4.4 to 8.4 V*
N14-4 (FPW) - Body ground W Phase 4.4 to 8.4 V*


HINT:
·

*: This Active Test restricts the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage measured in a previous step.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Result Proceed to
The U phase, V phase and W phase are all normal A
The U phase, V phase or W phase is abnormal B
The U phase, V phase and W phase are all abnormal C



A

5.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PUMP CONTROL ECU

C

6.INSPECT ECM (FPC TERMINAL)
5.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the fuel pump (for low pressure side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-2 (FPU) - N26-3 (BLPU) Always Below 1 Ω
N14-3 (FPV) - N26-4 (BLPV) Always Below 1 Ω
N14-4 (FPW) - N26-2 (BLPW) Always Below 1 Ω
N14-2 (FPU) or N26-3 (BLPU) - Body ground and other terminals Always 10 kΩ or higher
N14-3 (FPV) or N26-4 (BLPV) - Body ground and other terminals Always 10 kΩ or higher
N14-4 (FPW) or N26-2 (BLPW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (FPC TERMINAL)
A428848C20
0.417,1.083 0.833,1.333 0.417,0.25 1.719,1.844 1.719,1.354 false 0.135,0.083 0.448,0.24 0.313,0.156 10 false *a 1.615,1.865 2.042,2.052 0.427,0.188 10 false FPC 0.479,1.125 0.792,1.281 0.313,0.156 10 false N15
*a Front view of wire harness connector
(to Fuel Pump Control ECU)


a.

Disconnect the fuel pump control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition
N15-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI-MAIN NO. 2 RELAY)
A433503C02
0.094,0.052 0.406,0.208 0.313,0.156 10 false *1 2.188,0.479 2.5,0.635 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 2 Relay


a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

8.INSPECT EFI-MAIN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


c.

Remove the VVT relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block and junction block assembly.

HINT:

Remove the VVT relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - 2 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) or 2 (EFI-MAIN NO. 2 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the fuel pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - N15-1 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 2 relay) or N15-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
a.

Disconnect the fuel pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N15-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR