Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2019.02–2020.05
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) U

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  FAIL-SAFE CHART  


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC Code Component Fail-Safe Operation Fail-Safe Deactivation Condition
P001001
P001600
P136001
P136201
P261401
Cam timing control motor with EDU assembly The cam timing control motor with EDU assembly is operated to the most retarded position. Pass condition detected and then power switch turned off
P001100
P001200
VVT system Idling up (misfire prevention), or the cam timing control motor with EDU assembly is operated to the most retarded position. Pass condition detected and then power switch turned off
P001500 VVT system
·

Idle up (control of combustion worsening).

·

Stopping fuel-cut control


Pass condition detected
P003012
P003013
P101A9E
Air fuel ratio sensor (sensor 1) heater The ECM turns off the air fuel ratio sensor (sensor 1) heater. Power switch off
P003612
P003613
P102A9E
Air fuel ratio sensor (sensor 2) heater The ECM turns off the air fuel ratio sensor (sensor 2) heater. Power switch off
P006900
P222611
P222615
·

Manifold absolute pressure sensor

·

Atmospheric pressure sensor (ECM)


The ECM maintains the last learned atmospheric pressure value. Pass condition detected
P008700
P008800
P123513
Fuel pump assembly (for high pressure side)
·

The ECM performs fuel-cut when the engine speed and engine load are high.

·

Fuel pressure is set to 200 kPa (2 kgf/cm2, 29 psi)


Power switch off
P010012
P010014
Mass air flow meter sub-assembly The ECM calculates ignition timing according to the engine speed and throttle valve position. Pass condition detected and then power switch turned off
P011011
P011015
Intake air temperature sensor (mass air flow meter sub-assembly) The ECM estimates the intake air temperature to be 20°C (68°F). Pass condition detected and then power switch turned off
P011511
P011515
Engine coolant temperature sensor The ECM estimates the engine coolant temperature to be 80°C (176°F). Pass condition detected
P012011
P012015
P01201C
P022011
P022015
P060444
P060647
P060747
P060787
P060E49
P065714
P06579E
P16B09F
P210014
P210015
P211172
P211173
P211900
P211904
P211977
P21199B
P21352B
Electronic throttle control system The ECM cuts off throttle actuator current and the throttle valve is returned to a 7.5° throttle position by the return spring.
The ECM controls the fuel injection duration and ignition timing in accordance with the engine torque requested by the hybrid vehicle control ECU assembly. Fuel-cut is performed intermittently.*1
Pass condition detected and then power switch turned off
P019011
P019015
Fuel pressure sensor (for high pressure)
·

The ECM performs fuel-cut when the engine speed and engine load are high.

·

Fuel pressure is set to 200 kPa (2 kgf/cm2, 29 psi)


Pass condition detected and then power switch turned off
P020113
P020213
P020313
P020413
P062D13
ECM (injector driver) The ECM performs fuel-cut when the engine speed is 1000 rpm or more. Pass condition detected and then power switch turned off
P030000
P030027
P030085
P030100
P030200
P030300
P030400
*2
·

Fuel injector assembly

·

Electronic throttle control system


When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.

Under a low load and at a low engine speed:

- Fuel cut is performed on the malfunctioning cylinder.

2.

Under a high load and at a high engine speed:

- Throttle valve opening angle control is performed.

- Fuel cut is performed on all cylinders or the malfunctioning cylinder.


Pass condition detected and then power switch turned off
P032511
P032515
Knock control sensor The ECM sets the ignition timing to maximum retard. Power switch off
P04019C
P040318
P040319
P140018
P140019
EGR valve assembly The ECM fully closes the EGR valve and stops EGR control. Pass condition detected
P052012
P052014
P052024
P05202A
Oil pressure sensor (oil pressure and temperature sensor) Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity. Pass condition detected and then power switch turned off
P052477
P15F009
P15F077
Engine oil pressure control system
·

Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.

·

The maximum engine speed is limited in accordance with the abnormal pressure.


Pass condition detected and then power switch turned off
P059F73
P05A072
P05A211
P05A212
P05A213
P05A27E
P05A27F
P05B131
Swing grille actuator assembly The grille shutter system control is suspended. Normal system condition detected, power switch turned off then on (IG) and normal grille shutter closing and opening operation performed
P05B112
P05B114
Swing grille actuator assembly
·

Grille shutter closed position:

The grille shutter is fully opened and then grille shutter system control is suspended.

·

Grille shutter open position:

The grille shutter system control is suspended.


Normal system condition detected, power switch turned off then on (IG) and normal grille shutter closing and opening operation performed
P06DA13 Oil pressure control valve assembly Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity. Pass condition detected and then power switch turned off
P107A11
P107A15
Fuel pressure sensor (for low pressure side)
·

Fuel pump (for low pressure side) control is maintained.

·

Output power is limited.


Pass condition detected and then power switch turned off
P15F109 Engine oil pressure control system
·

Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.

·

Output power is limited.


Pass condition detected and then power switch turned off
P15F177 Engine oil pressure control system Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity. Pass condition detected and then power switch turned off
P21CF13
P21D013
P21D113
P21D213
Port fuel injector assembly The ECM performs fuel-cut when the engine speed is 1000 rpm or more. Pass condition detected and then power switch turned off
P223711
P223712
P223714
P223716
P223717
P22371A
P225111
P225112
Air fuel ratio sensor (sensor 1) Air fuel ratio sensor (sensor 1) air fuel ratio feedback control is stopped. Pass condition detected and then power switch turned off
P22AB11
P22AB12
P22AB13
P22AB16
P22AB17
P22B211
P22B212
Air fuel ratio sensor (sensor 2)
·

Control based on air fuel ratio sensor (sensor 2) air fuel ratio feedback is stopped.

·

The ECM turns off the air fuel ratio sensor (sensor 2) heater.


Pass condition detected and then power switch turned off
P244B00
P246300
Gasoline particulate filter system Output power is limited. Power switch off
P26CA12
P26CA31
P26CB71
Engine water pump assembly When the engine coolant temperature reaches 105°C (221°F), the engine speed is limited to 2500 rpm or less. Pass condition detected and then power switch turned off
P26CA14 Engine water pump assembly
·

When the engine coolant temperature reaches 105°C (221°F), the engine speed is limited to 2500 rpm or less.

·

The engine water pump assembly is controlled at a duty ratio of 85%.


Pass condition detected and then power switch turned off
P26CE37 Engine water pump assembly The engine water pump assembly is temporarily operated and stopped in a repeating cycle.
·

Output duty ratio of the WPO terminal repeats a cycle of 0% for 0 to 5 seconds and then 85% for 5 to 30 seconds.


Pass condition detected and then power switch turned off

HINT:
·

*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

·

*2: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.