Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.
Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.
If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.
When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.
2.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (When Installed to Vehicle)
When disposing of a curtain shield airbag assembly LH, use an unneeded vehicle to deploy the airbag.
Be sure to perform the following procedure when deploying the airbag.
Prepare a battery as the power source to deploy the airbag.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Refer to Precaution.
w/o Occupant Classification System:
for Gasoline Model with Occupant Classification System:
for HV Model with Occupant Classification System:
Remove the roof headlining assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
| *a | Lock Button |
|
Protective Tape |
|
Release in this Direction |
Disconnect the airbag connector.
Using a screwdriver, release the lock button and disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Tape the screwdriver tip before use.
Install SST.
After connecting the following SST to each other, connect them to the curtain shield airbag assembly LH.
Connect SST together (09082-00700 and 09082-10801).
To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.
Do not deploy the curtain shield airbag assembly LH if it rattles due to looseness and the tightening bolts and clips, etc., for the inflator and deployment part of the curtain shield airbag assembly LH may fall off.
Do not deploy the curtain shield airbag assembly LH if the deployment part fell off.
If the curtain shield airbag assembly LH is deployed when it rattles or parts have fallen off, the curtain shield airbag assembly LH may fly off and cause serious injuries.
| *a | 10 m (32.8 ft.) or more |
Move SST at least 10 m (32.8 ft.) away from the rear side window of the vehicle.
Maintaining sufficient clearance for SST wire harness in the rear side window, close all doors and windows of the vehicle.
Do not deploy with all the doors and door windows open.
If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.
Take care not to damage SST wire harness.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press SST activation switch to deploy the airbag.
Do not deploy with people inside or around the vehicle.
If deployed with people inside or around the vehicle, serious injuries may occur.
The airbag is deployed as the LED of SST activation switch comes on.
Remove the curtain shield airbag assembly LH.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL
The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.
If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.
If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
After removal, quickly seal the curtain shield airbag assembly LH in a plastic bag.
Dispose of the curtain shield airbag assembly LH.
Place the curtain shield airbag assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.
The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.
If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.
If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
Never dispose of a curtain shield airbag assembly LH with an undeployed airbag.
If an undeployed curtain shield airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.
Always wash your hands with water after completing the operation.
3.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (When not Installed to Vehicle)
Be sure to observe the following procedure when deploying the airbag.
Prepare a battery as the power source to deploy the airbag.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Refer to Precaution.
w/o Occupant Classification System:
for Gasoline Model with Occupant Classification System:
for HV Model with Occupant Classification System:
Remove the curtain shield airbag assembly LH.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL
except Rollover Type:
Cut off the 3 cable ties and detach the claw to remove the center retainer.
for Rollover Type:
Cut off the 3 cable ties and remove the center retainer.
| *a | Cut Here |
Cut off the curtain shield airbag assembly LH deployment portion.
Wear safety glasses and gloves.
The dust may enter the eyes or be breathed in.
| *a | Wire Diameter |
|
Stripped Wire Cross Sectional Area |
Using braided wire, tie down the curtain shield airbag inflator to an unneeded tire.
Cross-sectional area of stripped wire
1.25 mm2 (0.0019 in.2) or more
If the wire harness is too thin or an alternative object is used to tie down the curtain shield airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).
To calculate the area of the cross-sectional area of stripped wire:
Area = 3.14 x (Diameter)2 / 4
| *a | Width |
| *b | Inner Diameter |
| *c | Outlet |
except Rollover Type:
Position the curtain shield airbag inflator inside the tire.
Must exceed the following dimensions
185 mm (7.28 in.)
360 mm (1.18 ft.)
The tire may be damaged by the airbag deployment, so use an unneeded tire.
| *a | Width |
| *b | Inner Diameter |
| *c | Outlet |
for Rollover Type:
Position the curtain shield airbag inflator inside the tire.
Must exceed the following dimensions
185 mm (7.28 in.)
360 mm (1.18 ft.)
The tire may be damaged by the airbag deployment, so use an unneeded tire.
Install SST.
except Rollover Type:
After connecting the following SST to each other, connect them to the curtain shield airbag inflator.
for Rollover Type:
After connecting the following SST to each other, connect them to the curtain shield airbag inflator.
except Rollover Type:
Place the tires.
| *a | Outlet |
| *b | Remove looseness |
Do not install the curtain shield airbag inflator with the outlet facing down.
When securing the curtain shield airbag inflator, make sure there is no looseness in the wire harness.
If installed with the outlet facing down or looseness in the wire harness, the deployed curtain shield airbag inflator and tire may fly off and cause serious injuries.
| *a | Tires (2 or more) |
Place at least 2 tires under the tire to which the curtain shield airbag inflator is tied.
185 mm (7.28 in.)
360 mm (1.18 ft.)
Do not place SST connector under the tire because it could be damaged.
Place at least 2 tires onto the tire to which the curtain shield airbag inflator is tied. The top tire should have a wheel installed.
The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.
Tie the tires together with 2 wires.
for Rollover Type:
Place the tires.
| *a | Outlet |
| *b | Remove looseness |
Do not install the curtain shield airbag inflator with the outlet facing down.
When securing the curtain shield airbag inflator, make sure there is no looseness in the wire harness.
If installed with the outlet facing down or looseness in the wire harness, the deployed curtain shield airbag inflator and tire may fly off and cause serious injuries.
Place at least 2 tires under the tire to which the curtain shield airbag inflator is tied.
185 mm (7.28 in.)
360 mm (1.18 ft.)
Do not place SST connector under the tire because it could be damaged.
| *a | Tires (2 or more) |
Place at least 2 tires onto the tire to which the curtain shield airbag inflator is tied. The top tire should have a wheel installed.
The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.
Tie the tires together with 2 wires.
except Rollover Type:
Install SST.
| *a | 10 m (32.8 ft.) or more |
Connect SST together (09082-00700 and 09082-10801).
To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.
Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.
for Rollover Type:
Install SST.
Connect SST together (09082-00700 and 09082-10801).
To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.
| *a | 10 m (32.8 ft.) or more |
Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.
Deploy the airbag.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the curtain shield airbag inflator is tied.
Press SST activation switch to deploy the airbag.
Do not deploy with people around the tire.
If deployed with people around the tire, serious injuries may occur.
The airbag is deployed as the LED of SST activation switch comes on.
Dispose of the curtain shield airbag inflator.
The curtain shield airbag inflator becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to a curtain shield airbag inflator with a deployed airbag.
If water is applied to the curtain shield airbag inflator immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed curtain shield airbag inflator.
If the curtain shield airbag inflator is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
Never dispose of a curtain shield airbag inflator with an undeployed airbag.
If an undeployed curtain shield airbag inflator is disposed of, and then deploys for any reason, unforeseen injuries may occur.
Always wash your hands with water after completing the operation.
Remove the curtain shield airbag inflator from the tire.
Place the curtain shield airbag inflator in a plastic bag, tie it tightly, and dispose of it according to local regulations.