Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) U

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  TERMINALS OF ECM  


A425145E08
1.833,0.792 2.281,1.042 0.448,0.25 5.448,0.813 5.896,1.063 0.448,0.25 1.938,0.833 2.396,1.031 0.458,0.198 10 false C45 5.542,0.865 6,1.063 0.458,0.198 10 false A24

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals are shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-1 (BATT) - A24-10 (E1) G - W-B Auxiliary battery (for measuring auxiliary battery voltage and ECM memory) Always 11 to 16 V
A24-2 (IGSW) - A24-10 (E1) P - W-B Power switch signal Power switch on (IG) 11 to 14 V
A24-3 (VPMP) - A24-10 (E1) BR - W-B Vent valve (built into canister pump module) Power switch on (IG) 11 to 14 V
A24-5 (MPMP) - A24-10 (E1) P - W-B Leak detection pump (canister pump module) Leak detection pump OFF Below 3 V
Leak detection pump ON 11 to 14 V
A24-6 (FPC) - A24-10 (E1) LG - W-B Fuel pump control Power switch on (IG) Below 1.5 V
A24-7 (CAN+) - A24-10 (E1) P - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 1)
A24-8 (CANH) - A24-10 (E1) B - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 1)
A24-9 (+B) - A24-10 (E1) L - W-B
·

Power source of ECM

·

Power source of throttle actuator


Power switch on (IG) 11 to 14 V
A24-10 (E1) - Body ground W-B - - Ground Always Below 1 Ω
A24-12 (CCV2) - A24-10 (E1) Y - W-B Fuel vapor containment valve assembly signal Fuel vapor containment valve assembly on (open) Below 1.0 V
Fuel vapor containment valve assembly off (closed) 11 to 14 V
A24-15 (MREL) - A24-10 (E1) W - W-B EFI-MAIN NO. 1 relay operation signal Power switch on (IG) Below 1.5 V
A24-16 (NEO) - A24-10 (E1) B - W-B Crankshaft revolution signal Idling with warm engine Pulse generation
(See waveform 2)
A24-17 (CAN-) - A24-10 (E1) W - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 3)
A24-18 (CANL) - A24-10 (E1) W - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 3)
A24-24 (G2O) - A24-10 (E1) R - W-B Camshaft revolution signal Idling with warm engine Pulse generation
(See waveform 4)
A24-31 (LIDO) - A24-10 (E1) GR - W-B Fuel lid courtesy switch signal Fuel lid closed Below 1.0 V
Fuel lid open 11 to 14 V
A24-32 (RFC) - A24-10 (E1) SB - W-B Cooling fan control signal Power switch on (IG), A/C switch on (max cool) Pulse generation
(See waveform 5)
A24-34 (IREL) - A24-10 (E1) P - W-B D INJ relay operation signal Power switch on (IG) 11 to 14 V
A24-35 (+B2) - A24-10 (E1) L - W-B Power source of ECM Power switch on (IG) 11 to 14 V
A24-36 (E2) - Body ground W-B - - Ground Always Below 1 Ω
A24-38 (FUEL) - A24-10 (E1) G - W-B Fuel lid opener switch signal Fuel lid opener switch pressed Below 1.0 V
Fuel lid opener switch not pressed 4.5 to 5.5 V
A24-45 (EC) - Body ground BR - - Ground Always Below 1 Ω
A24-41 (LSTM) - A24-10 (E1) L - W-B Fuel lid operation signal for combination meter assembly Multi-information display displaying "Close Fuel Lid" Pulse generation
(See waveform 6)
Multi-information display displaying "Ready to Refuel" Pulse generation
(See waveform 7)
Power switch on (IG) 11 to 14 V
A24-44 (FREL) - A24-10 (E1) Y - W-B Fuel lid lock with motor assembly operation signal Fuel lid lock with motor assembly operating Below 1.0 V
Fuel lid lock with motor assembly not operating 11 to 14 V
A24-48 (VCPP) - A24-49 (EPPM) W - P Power source for canister pressure sensor (specific voltage) Power switch on (IG) 4.5 to 5.5 V
A24-50 (PPMP) - A24-49 (EPPM) BE - P Canister pressure sensor (built into canister pump module) Power switch on (IG) 3.0 to 3.6 V
A24-53 (+BD1) - A24-10 (E1) W - W-B Power source of ECU (injector driver) Power switch on (IG) 11 to 14 V
A24-54 (E1D1) - Body ground W-B - - Ground Always Below 1 Ω
A24-57 (VPTK) - A24-56 (EPTK) V - R Power source of fuel tank pressure sensor (specific voltage) Engine stopped, power switch on (IG) 4.75 to 5.25 V
A24-55 (PTNK) - A24-56 (EPTK) SB - R Fuel tank pressure sensor signal Engine stopped, power switch on (IG) 0.27 to 4.73 V
C45-1 (M-) - A24-10 (E1) L - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 8)
C45-2 (M+) - A24-10 (E1) B - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 9)
C45-3 (EGA+) - A24-10 (E1) R - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 10)
C45-4 (EGA-) - A24-10 (E1) L - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 10)
C45-5 (EGB-) - A24-10 (E1) V - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 10)
C45-6 (EGB+) - A24-10 (E1) GR - W-B EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 10)
C45-7 (HTHM) - A24-10 (E1) LA-G - W-B Thermostat heater (water inlet with thermostat sub-assembly) operation signal Power switch on (IG) 11 to 14 V
C45-8 (HA1B) - A24-10 (E1) R - W-B Air fuel ratio sensor (sensor 2) heater operation signal Power switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 11)
C45-9 (HA1A) - A24-10 (E1) L - W-B Air fuel ratio sensor (sensor 1) heater operation signal Power switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 12)
C45-10 (#2D-) - A24-10 (E1) G - W-B Direct fuel injector assembly signal (No. 2 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-11 (#2D+) - A24-10 (E1) L - W-B Direct fuel injector assembly signal (No. 2 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-12 (#3D+) - A24-10 (E1) W - W-B Direct fuel injector assembly signal (No. 3 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-13 (#3D-) - A24-10 (E1) R - W-B Direct fuel injector assembly signal (No. 3 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-14 (#4D-) - A24-10 (E1) V - W-B Direct fuel injector assembly signal (No. 4 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-15 (#4D+) - A24-10 (E1) P - W-B Direct fuel injector assembly signal (No. 4 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-16 (#1D+) - A24-10 (E1) W - W-B Direct fuel injector assembly signal (No. 1 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-17 (#1D-) - A24-10 (E1) BR - W-B Direct fuel injector assembly signal (No. 1 cylinder) Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 13)
C45-18 (FP1-) - A24-10 (E1) L - W-B Fuel pump assembly (for high pressure side) signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 14)
C45-19 (FP1+) - A24-10 (E1) G - W-B Fuel pump assembly (for high pressure side) signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 14)
C45-20 (VOP-) - A24-10 (E1) P - W-B Oil pressure control valve operation signal Idling with warm engine Pulse generation
(See waveform 15)
C45-21 (VOP+) - A24-10 (E1) G - W-B Oil pressure control valve operation signal Idling with warm engine Pulse generation
(See waveform 15)
C45-26 (OE1+) - C45-25 (OE1-) LA-B - LA-W Cam timing oil control solenoid assembly operation signal Idling Pulse generation
(See waveform 16)
C45-28 (EDT1) - A24-10 (E1) P - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Pulse generation
(See waveform 17)
C45-42 (WSV1) - A24-10 (E1) LA-W - W-B Flow shutting valve operation signal Power switch on (IG) 11 to 14 V
C45-46 (IGT4) - A24-10 (E1) B - W-B No. 4 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 18)
C45-47 (IGT3) - A24-10 (E1) P - W-B No. 3 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 18)
C45-48 (IGT2) - A24-10 (E1) V - W-B No. 2 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 18)
C45-49 (IGT1) - A24-10 (E1) W - W-B No. 1 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 18)
C45-50 (WPO) - A24-10 (E1) LA-G - W-B Electric water pump assembly signal Idling with warm engine Pulse generation
(See waveform 19)
C45-51 (WPI) - A24-10 (E1) LA-B - W-B Electric water pump assembly signal Idling with warm engine Pulse generation
(See waveform 20)
C45-66 (PRG) - A24-10 (E1) P - W-B Purge VSV operation signal Power switch on (IG) 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 21)
C45-70 (EMR1) - A24-10 (E1) LG - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Pulse generation
(See waveform 22)
C45-71 (EMF1) - A24-10 (E1) B - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Below 5.0 V
C45-72 (EMD1) - A24-10 (E1) L - W-B Cam timing control motor with EDU assembly signal Idling with warm engine Pulse generation
(See waveform 23)
C45-73 (#40) - A24-10 (E1) P - W-B Port fuel injector assembly signal (No. 4 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 24)
C45-74 (#30) - A24-10 (E1) W - W-B Port fuel injector assembly signal (No. 3 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 24)
C45-75 (#20) - A24-10 (E1) G - W-B Port fuel injector assembly signal (No. 2 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 24)
C45-76 (#10) - A24-10 (E1) B - W-B Port fuel injector assembly signal (No. 1 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 24)
C45-78 (VCVG) - A24-10 (E1) R - W-B Power source of mass air flow meter sub-assembly (specific voltage) Power switch on (IG) 4.8 to 5.2 V
C45-84 (VCPF) - A24-10 (E1) LG - W-B Power source of fuel pressure sensor (for low pressure side) (specific voltage) Power switch on (IG) 4.5 to 5.5 V
C45-87 (VTA2) - C45-110 (ETA) V - G Throttle position sensor signal (for sensor malfunction detection) Engine stopped, power switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
C45-88 (VCV1) - A24-10 (E1) L - W-B Power source of camshaft position sensor (for intake camshaft) (specific voltage) Power switch on (IG) 4.5 to 5.5 V
C45-90 (VV1+) - C45-89 (VV1-) B - LG Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 25)
C45-91 (EV1+) - C45-114 (EV1-) V - G Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 25)
C45-93 (NE+) - C45-115 (NE-) L - P Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 26)
C45-94 (A1A-) - A24-10 (E1) G - W-B Air fuel ratio sensor (sensor 1) signal Power switch on (IG) 1.24 to 4.22 V
C45-95 (A1A+) - A24-10 (E1) R - W-B Air fuel ratio sensor (sensor 1) signal Power switch on (IG) 1.46 to 4.22 V
C45-97 (PR) - C45-96 (EPR) L - V Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
C45-98 (VCPR) - C45-96 (EPR) LG - V Power source of fuel pressure sensor (for high pressure side) (specific voltage) Power switch on (IG) 4.75 to 5.25 V
C45-99 (VCPE) - C45-100 (EPEO) R - L Power source of engine oil pressure sensor (specific voltage) Power switch on (IG) 4.5 to 5.5 V
C45-101 (VG) - C45-79 (E2G) W - G Mass air flow meter sub-assembly signal Power switch on (IG) Pulse generation
(See waveform 27)
C45-102 (THA) - C45-79 (E2G) V - G Intake air temperature sensor (mass air flow meter sub-assembly) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C45-107 (PFL) - C45-61 (EPFL) V - L Fuel pressure sensor (for low pressure side) signal Idling with warm engine 0.75 to 4.5 V
C45-108 (VTA1) - C45-110 (ETA) P - G Throttle position sensor signal (for engine control) Engine stopped, power switch on (IG), accelerator pedal fully released 0.6 to 1.1 V
C45-109 (VCTA) - C45-110 (ETA) R - G Power source of throttle position sensor (specific voltage) Engine stopped, power switch on (IG) 4.5 to 5.5 V
C45-111 (KNK1) - C45-112 (EKNK) B - W Knock control sensor signal Engine speed maintained at 2500 rpm after warming up engine Pulse generation
(See waveform 28)
C45-113 (VCE1) - A24-10 (E1) L - W-B Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Power switch on (IG) 4.5 to 5.5 V
C45-116 (VCNE) - A24-10 (E1) V - W-B Power source of crankshaft position sensor (specific voltage) Power switch on (IG) 4.5 to 5.5 V
C45-117 (A1B-) - A24-10 (E1) W - W-B Air fuel ratio sensor (sensor 2) signal Power switch on (IG) 1.17 to 4.49 V
C45-118 (A1B+) - A24-10 (E1) B - W-B Air fuel ratio sensor (sensor 2) signal Power switch on (IG) 1.53 to 5.96 V
C45-120 (PIM) - C45-119 (EPIM) P - G Manifold absolute pressure sensor signal Power switch on (IG) 3.0 to 4.5 V
C45-121 (VCPM) - C45-119 (EPIM) B - G Power source of manifold absolute pressure sensor (specific voltage) Power switch on (IG) 4.75 to 5.25 V
C45-122 (PEO) - C45-100 (EPEO) W - L Oil pressure sensor signal Idling with warm engine 0.5 to 4.5 V
C45-123 (THEO) - C45-100 (EPEO) V - L Engine oil temperature sensor signal Power switch on (IG) 0.54 to 4.86 V
C45-125 (THW) - C45-124 (ETHW) L - P Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C45-129 (THTW) - C45-130 (ETHT) P - W No. 2 engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V

WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Between CAN+ and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A214025E27
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Crankshaft Revolution Signal from ECM to Inverter with Converter Assembly
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Between CAN- and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 4


A214025E25
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Camshaft Revolution Signal from ECM to Inverter with Converter Assembly
ECM Terminal Name Between G2O and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A282867E08
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Power switch on (IG), A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 6


A375177E01
2.688,0.094 3.24,0.302 0.552,0.208 10 false 5 V/DIV. 2.771,0.938 3.323,1.146 0.552,0.208 10 false GND 1.302,1.896 2.052,2.063 0.75,0.167 10 false 20 ms./DIV.

Fuel Lid Operation Signal for Combination Meter Assembly
ECM Terminal Name Between LSTM and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Multi-information display displaying "Close Fuel Lid"


WAVEFORM 7


A375178E01
2.667,0.094 3.24,0.292 0.573,0.198 10 false 5 V/DIV. 2.76,0.927 3.333,1.125 0.573,0.198 10 false GND 1.313,1.906 2.104,2.073 0.792,0.167 10 false 20 ms./DIV.

Fuel Lid Operation Signal for Combination Meter Assembly
ECM Terminal Name Between LSTM and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Multi-information display displaying "Ready to Refuel"


WAVEFORM 8


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Operation Signal (Negative Terminal)
ECM Terminal Name Between M- and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Operation Signal (Positive Terminal)
ECM Terminal Name Between M+ and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 10


A405745E03
2.688,0.073 3.302,0.427 0.615,0.354 10 false 5 V/DIV. 1.344,1.896 2.563,2.156 1.219,0.26 10 false 5 μs./DIV. 0.198,0.313 0.813,0.667 0.615,0.354 10 false EGA+ 0.229,1.365 0.844,1.719 0.615,0.354 10 false EGA- 2.74,0.792 3.354,1.146 0.615,0.354 10 false GND 2.75,1.594 3.365,1.948 0.615,0.354 10 false GND 0.167,0.458 0.781,0.813 0.615,0.354 10 false (EGB+) 0.198,1.51 0.813,1.865 0.615,0.354 10 false (EGB-)

EGR Valve Assembly Operation Signal
ECM Terminal Name CH1: Between EGA+ and E1
CH2: Between EGA- and E1
CH1: Between EGB+ and E1
CH2: Between EGB- and E1
Tester Range 5 V/DIV., 5 μs./DIV.
Condition Idling with warm engine

HINT:

When the EGR valve assembly is operating, a waveform is produced at each terminal.



WAVEFORM 11


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 2) Heater Operation Signal
ECM Terminal Name Between HA1B and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 12


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal
ECM Terminal Name Between HA1A and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 13


A405747E01
0.302,0.573 0.76,0.771 0.458,0.198 10 false CH1 0.313,0.938 0.771,1.135 0.458,0.198 10 false CH2 1.208,1.896 2.031,2.146 0.823,0.25 10 false 200 μs./DIV. 2.667,0.094 3.354,0.5 0.688,0.406 10 false 50 V/DIV. 2.781,0.594 3.24,0.792 0.458,0.198 10 false GND 2.771,0.948 3.229,1.146 0.458,0.198 10 false GND

No. 1 (to No. 4) Direct Fuel Injector Assembly Signal
ECM Terminal Name CH1: Between #1D+ and E1
CH2: Between #1D- and E1
CH1: Between #2D+ and E1
CH2: Between #2D- and E1
CH1: Between #3D+ and E1
CH2: Between #3D- and E1
CH1: Between #4D+ and E1
CH2: Between #4D- and E1
Tester Range 50 V/DIV., 200 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 14


A405748E01
2.771,0.094 3.406,0.438 0.635,0.344 10 false 20 V/DIV. 1.26,1.885 2.573,2.177 1.313,0.292 10 false 500 μs./DIV. 0.26,0.406 1.573,0.698 1.313,0.292 10 false FP1+ 0.271,1.083 1.583,1.375 1.313,0.292 10 false FP1- 2.76,0.438 3.135,0.865 0.375,0.427 10 false GND 2.76,1.104 3.135,1.531 0.375,0.427 10 false GND

Fuel Pump Assembly (for High Pressure Side) Signal
ECM Terminal Name CH1: Between FP1+ and E1
CH2: Between FP1- and E1
Tester Range 20 V/DIV., 500 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 15


A405749E01
2.708,0.115 3.281,0.49 0.573,0.375 10 false 5 V/DIV. 1.313,1.885 2.479,2.135 1.167,0.25 10 false 20 ms./DIV. 0.198,0.75 0.771,1.125 0.573,0.375 10 false VOP+ 0.219,1.26 0.792,1.635 0.573,0.375 10 false VOP- 2.76,0.781 3.333,1.156 0.573,0.375 10 false GND 2.76,1.271 3.333,1.646 0.573,0.375 10 false GND

Oil Pressure Control Valve Operation Signal
ECM Terminal Name CH1: Between VOP+ and E1
CH2: Between VOP- and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 16


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly Operation Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 17


A149745E04
2.844,1.802 3.302,2 0.458,0.198 10 false GND 2.667,0.729 3.302,0.938 0.635,0.208 10 false 1 V/DIV. 1.344,2.521 2.281,2.823 0.938,0.302 10 false 5 ms./DIV.

Cam Timing Control Motor with EDU Assembly Signal (EDT Signal)
ECM Terminal Name Between EDT1 and E1
Tester Range 1 V/DIV., 5 ms./DIV.
Condition Idling with warm engine


WAVEFORM 18


A247035E03
2.771,0.135 3.385,0.313 0.615,0.177 10 false 5 V/DIV. 3.031,0.604 3.365,0.781 0.333,0.177 10 false GND 3.031,0.938 3.365,1.115 0.333,0.177 10 false GND 3.031,1.271 3.365,1.448 0.333,0.177 10 false GND 3.031,1.594 3.365,1.771 0.333,0.177 10 false GND 2.052,1.885 2.813,2.073 0.76,0.188 10 false 20 ms./DIV. 0.375,0.604 0.813,0.823 0.438,0.219 10 false IGT1 0.365,0.927 0.802,1.146 0.438,0.219 10 false IGT2 0.365,1.26 0.802,1.479 0.438,0.219 10 false IGT3 0.375,1.583 0.813,1.802 0.438,0.219 10 false IGT4

Ignition Coil Assembly Signal (IGT Signal)
ECM Terminal Name Between IGT (1 to 4) and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly)
ECM Terminal Name Between WPO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the engine water pump assembly speed.



WAVEFORM 20


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM)
ECM Terminal Name Between WPI and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump assembly speed increases.



WAVEFORM 21


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 22


A149746E04
2.833,1.844 3.292,2.042 0.458,0.198 10 false GND 2.625,0.729 3.281,0.958 0.656,0.229 10 false 2 V/DIV. 1.333,2.573 2.281,2.813 0.948,0.24 10 false 5 ms./DIV.

Cam Timing Control Motor with EDU Assembly Signal (EMR Signal)
ECM Terminal Name Between EMR1 and E1
Tester Range 2 V/DIV., 5 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 23


A150215E05
2.833,1.823 3.333,2.021 0.5,0.198 10 false GND 1.177,2.521 2.302,2.771 1.125,0.25 10 false 100 ms./DIV. 2.667,0.677 3.302,0.927 0.635,0.25 10 false 2 V/DIV.

Cam Timing Control Motor with EDU Assembly Signal (EMD Signal)
ECM Terminal Name Between EMD1 and E1
Tester Range 2 V/DIV., 100 ms./DIV.
Condition Idling with warm engine


WAVEFORM 24


A287799E11
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

No. 1 (to No. 4) Port Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E1
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine (Data List item "Injection Mode" displaying "Port")

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.




WAVEFORM 25


A255508E20
0.052,0.031 0.656,0.188 0.604,0.156 10 5 V/DIV. 0.167,0.656 0.49,0.823 0.323,0.167 10 CH1 0.156,1.448 0.479,1.615 0.323,0.167 10 CH2 0.094,0.844 0.49,1.052 0.396,0.208 10 (VV1) 0.083,1.604 0.479,1.833 0.396,0.229 10 (EV1) 3.052,0.813 3.396,0.958 0.344,0.146 10 GND 3.052,1.573 3.396,1.719 0.344,0.146 10 GND 1.271,1.865 2.021,2.042 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 26


A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 27


A337204E05
0.115,1.417 0.469,1.615 0.354,0.198 10 false GND 1.406,1.958 2.188,2.156 0.781,0.198 10 false 100 μs./DIV. 2.813,0.167 3.406,0.375 0.594,0.208 10 false 1 V/DIV.

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Power switch on (IG)


WAVEFORM 28


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.