Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P00B162  Radiator Coolant Temperature Sensor Signal Compare Failure  


DESCRIPTION

This engine uses a No. 2 engine coolant temperature sensor and an intake air temperature sensor to detect temperatures related to engine operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance decreases. These variations in resistance are transmitted to the ECM as voltage changes.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P00B162 Radiator Coolant Temperature Sensor Signal Compare Failure All of the following conditions are met (2 trip detection logic):
1.

The auxiliary battery voltage is 10.5 V or higher.

2.

7 hours or more have elapsed since the power switch was turned off in the previous trip.

3.

Less than 20 seconds since a cold engine start was performed.

4.

The intake air temperature is -10°C (14°F) or higher.

5.

The difference between the readings of the No. 2 engine coolant temperature and intake air temperature is higher than 25°C (45°F).


·

Intake air temperature sensor (mass air flow meter sub-assembly)

·

No. 2 engine coolant temperature sensor

·

ECM


Comes on DTC stored SAE Code: P00B2

A375526E01
4.635,5.458 4.469,5.458 4.469,5.458 4.385,5.042 false 0.115,0.25 5.188,0.583 5.073,0.333 10 false Difference Between No. 2 Engine Coolant Temperature and Intake Air Temperature 0.688,1.125 0.979,1.417 0.292,0.292 10 false °C 0.677,1.479 0.969,1.771 0.292,0.292 10 false 40 0.667,2.24 0.958,2.531 0.292,0.292 10 false 25 0.479,3.177 0.771,3.469 0.292,0.292 10 false 0 0.635,3.844 0.927,4.135 0.292,0.292 10 false -25 0.365,5.292 1.479,5.521 1.115,0.229 10 false Power Switch off 1.448,5.063 2.625,5.313 1.177,0.25 10 false 7 hours or more 2.604,5.271 3.469,5.625 0.865,0.354 10 false Power Switch on (READY) 3.521,5.281 4.375,5.656 0.854,0.375 10 false Engine Start 4.708,5.375 6.333,5.677 1.625,0.302 10 false 15 to 20 seconds 4.115,4.323 4.417,4.583 0.302,0.26 10 false Fail 4.156,1.802 4.458,2.063 0.302,0.26 10 false Fail 5,2.396 5.438,2.635 0.438,0.24 10 false 25°C 5,3.813 5.438,4.052 0.438,0.24 10 false -25°C 6.354,4.917 6.792,5.156 0.438,0.24 10 false Time

MONITOR DESCRIPTION

The ECM monitors the difference between the No. 2 engine coolant temperature and the intake air temperature when the engine is started cold to accurately detect the engine temperature conditions. The monitor runs when the engine is started after 7 hours or more have elapsed since the power switch was turned off in the previous trip. If the difference between the engine coolant temperature and the intake air temperature on a cold start exceeds 25°C (45°F), the ECM interprets this as a malfunction in the No. 2 engine coolant temperature sensor circuit or intake air temperature sensor circuit, illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A213993E35
1.083,1.271 1.635,1.604 0.552,0.333 10 false Idling 0.396,2.302 1.74,2.583 1.344,0.281 10 false Power Switch off 2.094,1.656 2.573,2.083 0.479,0.427 10 false [A] 3.375,2.156 3.948,2.583 0.573,0.427 10 false [B] 5.229,1.125 5.698,1.49 0.469,0.365 10 false [C] 6.167,2.906 6.552,3.271 0.385,0.365 10 false [D] 4.719,2.625 6.167,2.969 1.448,0.344 10 false 20 seconds or more 2.948,2.563 4.198,2.958 1.25,0.396 10 false 7.5 hours or more 0.385,1.781 1.438,2.219 1.052,0.438 10 false Power Switch on (IG)

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) [A].

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off.

6.

With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].

7.

Turn the power switch on (IG).

8.

Turn the GTS on.

9.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

10.

Start the engine and wait 20 seconds or more [C].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P00B162.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [D] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P00B162)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs and record the Freeze Frame Data.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P00B162 is output A
DTC P00B162 and other DTCs are output B


HINT:

If any DTCs other than P00B162 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA (COOLANT TEMPERATURE AND RADIATOR COOLANT TEMPERATURE)

B

2.CHECK FREEZE FRAME DATA (COOLANT TEMPERATURE AND RADIATOR COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Using the GTS, read the values displayed in the freeze frame data recorded in step 1.

Powertrain > Engine > DTC(P00B162) > Freeze Frame Data
Tester Display
Coolant Temperature
Radiator Coolant Temperature
50040 372 205,360 P00B162

e.

Read the value displayed on the GTS.

Standard:

Difference between the Coolant Temperature and the Radiator Coolant Temperature is within 15°C (27°F).


HINT:

When the engine is cold, the value of the intake air temperature, ECM internal temperature and ambient temperature should be approximately the same.



Result:
Proceed to
OK
NG



OK

3.CHECK FREEZE FRAME DATA (COOLANT TEMPERATURE AND INTAKE AIR TEMPERATURE)

NG

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

3.CHECK FREEZE FRAME DATA (COOLANT TEMPERATURE AND INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Using the GTS, read the values displayed in the freeze frame data recorded in step 1.

Powertrain > Engine > DTC(P00B162) > Freeze Frame Data
Tester Display
Coolant Temperature
Intake Air Temperature
50040 372 205,214 P00B162

e.

Read the value displayed on the GTS.

Standard:

Difference between the Coolant Temperature and the Intake Air Temperature is within 15°C (27°F).


HINT:
·

When the engine is cold, the value of the intake air temperature, ECM internal temperature and ambient temperature should be approximately the same.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY