Home › Engine / Hybrid System › A25B-FXS (ENGINE CONTROL) › THROTTLE BODY › from 2019.02
RM3620E _51 Engine / Hybrid System _080116 A25B-FXS ENGINE CONTROL _0389137 THROTTLE BODY A

A25B-FXS ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A424099C01
1.01,0.323 1.229,0.323 1.229,0.323 1.406,0.667 true 0.792,0.24 1,0.427 0.208,0.188 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusion of the throttle body gasket oriented as shown in the illustration.


b.
A424100C01
2.74,1.74 2.74,1.427 true 2.667,3.104 2.667,2.792 true 2.229,1.073 2.438,1.292 0.208,0.219 10 false *a 2.115,1.323 2.333,1.51 0.219,0.188 10 false *b 2.813,0.844 3.021,1.031 0.208,0.188 10 false *d 2.427,2.198 2.74,2.375 0.313,0.177 10 false *e 2.219,1.563 2.427,1.781 0.208,0.219 10 false *a 3.052,2.427 3.26,2.646 0.208,0.219 10 false *a 3.042,2.938 3.25,3.156 0.208,0.219 10 false *a 3.156,2.667 3.365,2.854 0.208,0.188 10 false *c 2.677,1.76 2.885,1.979 0.208,0.219 10 false *f 2.615,3.125 2.823,3.344 0.208,0.219 10 false *f
*a 45° (Claw of Clip Location)
*b Left of Vehicle
*c Down
*d Top
*e Right of vehicle
*f Paint Mark


Connect the No. 6 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:
·

If the throttle body with motor assembly has been struck or dropped, replace it.

·

Make sure to position the clip as shown in the illustration.




c.

Install the throttle body with motor assembly to the intake manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the No. 5 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



e.

Connect the throttle body with motor assembly connector.


Hide 2.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A424101C01
0.948,3 0.948,2.417 0.948,2.417 1.156,2.417 true 0.542,3 0.542,2.865 0.542,2.865 0.417,2.708 true 1.708,3.083 1.708,2.521 1.708,2.521 1.844,2.521 true 1.938,2.531 1.938,2.115 1.938,2.115 2.156,2.115 true 2.052,2.438 2.052,2.115 true 0.469,3.021 0.656,3.229 0.188,0.208 10 false *a 1.208,2.323 1.417,2.542 0.208,0.219 10 false *b 1.625,3.094 1.844,3.313 0.219,0.219 10 false *c 2.177,2.021 2.396,2.198 0.219,0.177 10 false *d 1.896,3.094 2.115,3.302 0.219,0.208 10 false *e 2.531,2.469 2.719,2.646 0.188,0.177 10 false *f 2.75,2.646 2.958,2.875 0.208,0.229 10 false *g
*a Protrusion
*b Cutout
*c Hose Clamp End
*d Paint Mark
*e 2 mm (0.0787 in.)
*f 4 mm (0.157 in.)
*g End of Hose Clamp Location


Install the air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.

NOTICE:

Make sure that the end of the hose clamp is positioned as shown in the illustration.



c.
A424102C01
1.188,1.365 1.281,1.177 1.281,1.177 1.396,1.177 true 1.094,0.948 1.281,1.156 0.188,0.208 10 false *a 0.396,1.448 0.635,1.635 0.24,0.188 10 false *b 0.5,1.198 0.719,1.417 0.219,0.219 10 false *c 1.417,1.083 1.625,1.292 0.208,0.208 10 false *d 0.5,1.698 0.74,1.927 0.24,0.229 10 false *c
*a Top
*b Front of Vehicle
*c 45° (Claw of Clip Location)
*d Paint Mark


Connect the No. 2 PCV hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



d.

Attach the 2 grommets and pin to install the air cleaner assembly with air cleaner hose.


e.

Attach the wire harness clamp.


f.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 3.INSTALL INLET AIR CLEANER ASSEMBLY

a.
A424095E01
2.229,1.281 2.385,1.469 0.156,0.188 10 true 1 0.917,1.302 1.073,1.5 0.156,0.198 10 true 2

Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12601B 4.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY