Home › Engine / Hybrid System › A25B-FXS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR › from 2019.02
RM3620E _51 Engine / Hybrid System _080116 A25B-FXS ENGINE CONTROL _0389145 AIR FUEL RATIO SENSOR A

A25B-FXS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

for Sensor 2:

i.
A424135C01
2.625,1.021 2.771,1.521 2.771,1.521 2.938,1.521 true 1.625,1.125 1.802,1.302 0.177,0.177 10 true *a 3,1.438 3.333,1.625 0.333,0.188 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the front exhaust pipe assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.
A450534C01
2.521,0.552 2.604,0.229 2.604,0.229 2.74,0.229 true 2.198,0.719 2.448,0.938 2.448,0.938 2.615,0.729 true 2.771,0.125 2.958,0.323 0.188,0.198 10 true *a 2.385,0.958 2.573,1.135 0.188,0.177 10 true *b
*a White Heat Shrinking Tube
*b Wire Harness Clamp


Connect the air fuel ratio sensor connector.


iii.

Attach the 2 wire harness clamps so that the white heat shrinking tube is positioned as shown in the illustration.



b.

for Sensor 1:

i.
A424130C01
0.792,1.677 1.198,1.677 true 1.885,0.031 2.073,0.208 0.188,0.177 10 true *a 0.5,1.615 0.813,1.823 0.313,0.208 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.
A424131C01
2.719,0.49 2.792,0.26 2.792,0.26 2.917,0.26 true 2.531,0.563 2.469,0.979 2.469,0.979 2.719,0.927 true 2.958,0.177 3.125,0.354 0.167,0.177 10 true *a 2.302,0.99 2.458,1.156 0.156,0.167 10 true *b
*a Tie Band
*b Wire Harness Clamp


Connect the air fuel ratio sensor connector.


iii.

Attach the 3 wire harness clamps so that the tie band is positioned as shown in the illustration.



Hide 12601B 2.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY