Home › Engine / Hybrid System › A25B-FXS (EMISSION CONTROL) › CANISTER › from 2019.02
RM3620E _51 Engine / Hybrid System _080119 A25B-FXS EMISSION CONTROL _0389280 CANISTER A

A25B-FXS EMISSION CONTROL  CANISTER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 58166A 1.REMOVE FRONT FLOOR COVER LH

Hide 58167A 2.REMOVE FRONT CENTER FLOOR COVER

Hide 77740 3.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.

Disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

A433641C01
4.948,2.302 4.948,1.813 true 5.51,2.198 5.51,1.635 true 2.677,2.344 2.24,2.344 true 1.802,1.927 1.646,2.083 1.646,2.083 1.469,2.083 true 2.813,1.01 3.573,1.25 3.573,1.25 3.927,1.25 true 4.969,1.042 5.146,0.635 5.146,0.635 5.427,0.635 true 4.604,1.594 4.531,2 4.531,2 4.313,2 true 3.958,1.135 4.156,1.323 0.198,0.188 10 true *1 4.135,1.906 4.354,2.115 0.219,0.208 10 false *2 4.854,2.333 5.042,2.563 0.188,0.229 10 false *a 1.302,1.99 1.521,2.208 0.219,0.219 10 false *b 5.469,0.531 5.698,0.74 0.229,0.208 10 false *c 5.417,2.24 5.625,2.427 0.208,0.188 10 false *d 2.708,2.24 2.896,2.469 0.188,0.229 10 false *a
*1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull
V100137

Pull out - -


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to detach the lock claws and pull it down.


ii.

Pull off the fuel tank vent hose.



b.
A433642

Slide the clip and remove the purge line hose from the purge line pipe and canister (charcoal canister assembly).


c.

Slide the clip and disconnect the vent line hose from the canister (charcoal canister assembly).


d.
A441022

Remove the 2 bolts.


e.
A441023

Detach the claw and remove the canister (charcoal canister assembly) from the vehicle body as shown in the illustration.