Home › Engine / Hybrid System › A25B-FXS (ENGINE MECHANICAL) › CYLINDER HEAD › from 2019.02
RM3620E _51 Engine / Hybrid System _080117 A25B-FXS ENGINE MECHANICAL _0390041 CYLINDER HEAD A

A25B-FXS ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.


a.
A400471C01
2.25,1.635 2.25,1.188 false 2.188,1.677 2.5,1.875 0.313,0.198 10 false *a 1.667,0.688 1.979,0.885 0.313,0.198 10 false *b 1.667,1.896 1.979,2.094 0.313,0.198 10 false *c
*a Adhesive
*b Application Width
*c Distance


Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard Application Width:

1.0 to 7.0 mm (0.0394 to 0.276 in.)


Distance:

1.0 mm (0.0394 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Do not expose the spark plug tube to engine oil for at least 1 hour after installing it.




b.
A400472C01
2.219,3.156 2.531,3.354 0.313,0.198 10 false *a
*a Protrusion Height


Using a wooden block and hammer, tap in the 4 spark plug tubes to the specified protrusion height.

Standard Protrusion Height:

75.7 to 76.7 mm (2.98 to 3.02 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 17159 2.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A400473C01
1.927,2.344 2.24,2.542 0.313,0.198 10 false *a 2.406,2.563 2.719,2.76 0.313,0.198 10 false *b 1.917,2.792 2.229,2.99 0.313,0.198 10 false *c
*a 20 mm (0.787 in.)
*b 35 mm (1.38 in.)
*c 13 mm (0.512 in.)


Using an E8 "TORX" socket wrench, install the 7 stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

HINT:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


a.

Apply adhesive to the 4 No. 1 straight screw plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the No. 1 straight screw plugs within 3 minutes of applying adhesive.



b.
A400445

Using a 6 mm hexagon socket wrench, install the 4 No. 1 straight screw plugs to the cylinder head sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 13734A 4.INSTALL INTAKE VALVE SPRING SEAT

a.

Install the 8 intake valve spring seats to the cylinder head sub-assembly.


Hide 13734B 5.INSTALL EXHAUST VALVE SPRING SEAT

a.

Install the 8 exhaust valve spring seats to the cylinder head sub-assembly.


Hide 6.INSTALL VALVE STEM OIL SEAL

a.
A400476C01
0.75,1.552 1.042,1.927 1.042,1.927 1.198,1.927 true 2.615,1.563 2.438,1.885 2.438,1.885 2.25,1.885 true 0.667,0.104 0.979,0.302 0.313,0.198 10 false *a 2.635,0.104 2.948,0.302 0.313,0.198 10 false *b 1.271,1.854 1.583,2.052 0.313,0.198 10 false *c 2.073,1.792 2.385,1.99 0.313,0.198 10 false *d
*a Intake Valve Stem Oil Seal
*b Exhaust Valve Stem Oil Seal
*c Gold
*d Gray


Apply a light coat of engine oil to 16 new valve stem oil seals.

NOTICE:

Make sure to install each valve stem oil seal to the correct side. Installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve stem oil seals are gold and the exhaust valve stem oil seals are gray.



b.
A400477C01
2.5,1.802 2.365,1.802 2.365,1.802 1.917,1.354 true 0.51,0.75 0.688,0.75 false 2.188,2.052 2.5,2.25 0.313,0.198 10 false *b 1.021,2.031 1.333,2.229 0.313,0.198 10 false *a 2.563,1.729 3.021,1.927 0.458,0.198 10 false SST 0.208,0.677 0.667,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect


Using SST, push in the 16 valve stem oil seals.

SST
09201-41020  

NOTICE:
·

Failure to use SST will cause the valve stem oil seals to be damaged or improperly seated.

·

Do not push in the valve stem oil seals at an angle.




Hide 13711 7.INSTALL INTAKE VALVE

a.
A400478C01
2.51,1.552 2.823,1.75 0.313,0.198 10 false *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


b.

Install the 8 intake valves, 8 intake valve compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A400479N01
0.458,0.167 0.625,0.167 0.625,0.167 0.802,0.49 false 1.813,0.24 2.052,0.24 2.052,0.24 2.385,0.417 true 0.135,0.104 0.594,0.302 0.458,0.198 10 false SST 1.51,0.146 1.969,0.344 0.458,0.198 10 false SST

Using SST, compress each intake valve compression spring and install the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


d.
A400480

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.




Hide 13715 8.INSTALL EXHAUST VALVE

a.
A400484C01
2.479,1.552 2.792,1.75 0.313,0.198 10 false *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Install the 8 exhaust valves, 8 exhaust valve compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A400485N02
0.615,0.26 0.771,0.26 0.771,0.26 0.938,0.469 true 2.573,0.385 2.729,0.167 2.729,0.167 2.885,0.167 true 0.313,0.198 0.771,0.396 0.458,0.198 10 false SST 2.927,0.094 3.385,0.292 0.458,0.198 10 false SST

Using SST, compress each exhaust valve compression spring and install the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


d.
A404209

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.