Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY) › from 2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0390717 MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)  P0A1B1F  Generator Control Module Circuit Intermittent  


DESCRIPTION

If the motor generator control ECU, which is built into the inverter with converter assembly, is reset due to a problem with the power source in the inverter, the motor generator control ECU will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A1B1F Generator Control Module Circuit Intermittent Error in reset signal from the inverter assembly power source IC:
If internal power source voltage drops below the normal CPU operating voltage or the ROM/RAM is malfunctioning, the power source IC resets the MG ECU and stores this DTC.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 15 seconds or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C408930E02
0.125,1.208 1.052,1.583 0.927,0.375 10 false from Auxiliary Battery 1.583,1.354 2.354,1.646 0.771,0.292 10 false IGCT 3.573,1.365 4.177,1.594 0.604,0.229 10 false PCU 2.458,1.854 2.833,2.104 0.375,0.25 10 false IGCT 3.75,2.313 4.24,2.563 0.49,0.25 10 false MREL 3.146,3.25 3.521,3.5 0.375,0.25 10 false A29 5.469,3.583 5.844,3.833 0.375,0.25 10 false A87 5.479,3.75 6.854,4.281 1.375,0.531 10 false Inverter with Converter Assembly 3.146,3.427 4.542,4.01 1.396,0.583 10 false Hybrid Vehicle Control ECU Assembly 5.729,1.219 6.104,1.469 0.375,0.25 10 false +B 5.74,1.896 6.115,2.146 0.375,0.25 10 false +B2 5.75,2.49 6.281,2.771 0.531,0.281 10 false GND1 5.75,3.146 6.281,3.406 0.531,0.26 10 false GND2 5.438,1.073 5.698,1.354 0.26,0.281 10 false 36 5.448,1.76 5.708,2.042 0.26,0.281 10 false 35 5.51,3.021 5.771,3.302 0.26,0.281 10 false 8 5.51,2.344 5.771,2.625 0.26,0.281 10 false 9 3.51,2.208 3.844,2.49 0.333,0.281 10 false 5 3.896,1.094 4.156,1.375 0.26,0.281 10 false 2 3.458,1.094 3.719,1.375 0.26,0.281 10 false 1 1.5,1.094 1.76,1.375 0.26,0.281 10 false 1 1.938,1.094 2.198,1.375 0.26,0.281 10 false 2 2.833,1.479 3.094,1.76 0.26,0.281 10 false 1 2.271,1.479 2.531,1.76 0.26,0.281 10 false 2 2.26,1.094 2.521,1.375 0.26,0.281 10 false 3 2.844,1.094 3.104,1.375 0.26,0.281 10 false 5

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P0A1B1F only is output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C


Malfunction Content System Relevant DTC
Communication malfunction Motor generator control system P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message
Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011087 Lost Communication with Drive Motor Control Module "A" Missing Message


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

C

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A87 inverter with converter assembly connector.


c.

Remove the IGCT relay from the No. 3 relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

C410412C02
4.375,1.771 4.688,2 0.313,0.229 5.854,2.063 6.302,2.688 true 5.323,2.698 5.771,2.063 true 5.854,1.74 6.448,1.094 true 5.771,1.75 5.313,1.094 true 2.635,1.844 2.948,2.042 0.313,0.198 10 false *2 0.667,0.438 0.979,0.635 0.313,0.198 10 false *1 4.188,0.49 4.5,0.688 0.313,0.198 10 false *a 4.406,1.802 4.677,1.99 0.271,0.188 10 false A87 6.344,2.75 6.656,2.948 0.313,0.198 10 false +B 5.094,2.75 5.406,2.948 0.313,0.198 10 false +B2 4.917,0.875 5.323,1.063 0.406,0.188 10 false GND2 6.469,0.885 6.875,1.073 0.406,0.188 10 false GND1
*1 No. 3 Relay Block and Junction Block Assembly *2 IGCT Relay
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A87-36 (+B) - 5 (IGCT relay) Power switch off Below 1 Ω
A87-35 (+B2) - 5 (IGCT relay) Power switch off Below 1 Ω
A87-9 (GND1) - Body ground Power switch off Below 1 Ω
A87-8 (GND2) - Body ground Power switch off Below 1 Ω



e.

Install the IGCT relay.


f.

Reconnect the A87 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR