Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY) › from 2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0390716 HYBRID CONTROL SYSTEM(for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)  P300016  Hybrid/EV Battery Control System Circuit Voltage Below Threshold  


DESCRIPTION

The hybrid vehicle control ECU assembly alerts the driver and performs fail-safe control based on error signals received from the battery voltage sensor.

This DTC is stored if the HV battery is discharged excessively or the hybrid control system malfunctions.

HINT:

If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharging the HV battery will be able to restore the voltage. If the HV battery voltage has dropped excessively after the vehicle was left for a long time, the HV battery will need to be replaced.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P300016 Hybrid/EV Battery Control System Circuit Voltage Below Threshold Malfunction is received from the battery voltage sensor:
Voltage of a battery block drops drastically.
(1 trip detection logic)
·

Engine

·

Hybrid vehicle transaxle assembly

·

HV battery


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P300016
·

Hybrid Battery Block 1 to 11 Voltage

·

Hybrid Battery SOC

·

Hybrid Battery Voltage

·

Hybrid Battery Current

·

Engine Speed



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) with shift lever in P.

7.

Wait until the engine starts and then stops.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



HINT:
·

Thoroughly interview the customer as DTC P300016 may be stored if the SOC drops due to the vehicle being left with shift lever in N for a long time or running out of fuel.

·

When the engine cannot be started, DTC P300016 may be stored because the HV battery cannot be charged.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P300016 or P300000 only is output. A
DTCs other than P300016 or P300000 are also output. B


HINT:

If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharge the HV battery and then repair the malfunctioning part.



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (ENGINE)

B

2.CHECK DTC OUTPUT (ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



e.

Turn the power switch off.



A

3.CHECK ENGINE START

B

3.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

NOTICE:

Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.


HINT:

Depressing the accelerator pedal with shift lever in P will cause the engine to start.


Result:
Result Proceed to
The engine does not start. A
The engine starts. B



c.

Turn the power switch off.



A

4.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

B

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

4.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)
a.

Make sure that the shift lever is in P position.


b.

Lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


Result:
Result Proceed to
The crankshaft rotates smoothly. A
The crankshaft does not rotate smoothly. B



d.

Lower the vehicle.



A

5.CHECK HV BATTERY

B

6.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
5.CHECK HV BATTERY
a.

Turn the power switch off.


b.

Wait 10 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 11 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
Hybrid Battery Block 10 Voltage
Hybrid Battery Block 11 Voltage
50003 397 161,162,163,164,165,166,167,168,169,170,307

f.

Read the Data List.

Result:
Result Proceed to
Any of "Hybrid Battery Block 1, 2, 9, 10, 11 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7, 8 Voltage" is 24.0 V or less A
Other than above B



g.

Turn the power switch off.



A

B

10.CLEAR DTC
6.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
a.

Lift up the vehicle.


b.

Turn the power switch on (IG).


c.

Depress the brake pedal and move the shift lever to N.


d.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


Result:
Result Proceed to
The crankshaft does not rotate smoothly. A
The crankshaft rotates smoothly. B



e.

Lower the vehicle.


f.

Turn the power switch off.



A

7.REPAIR OR REPLACE ENGINE

B

11.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
7.REPAIR OR REPLACE ENGINE
Result:
Proceed to
NEXT



NEXT

8.CHECK ENGINE START
8.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

NOTICE:

Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.


HINT:

Depressing the accelerator pedal with shift lever in P will cause the engine to start.


Result:
Result Proceed to
The engine does not start. A
The engine starts. B



c.

Turn the power switch off.



A

9.CHECK HV BATTERY

B

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

9.CHECK HV BATTERY
a.

Turn the power switch off.


b.

Wait 10 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 11 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
Hybrid Battery Block 10 Voltage
Hybrid Battery Block 11 Voltage
50003 397 161,162,163,164,165,166,167,168,169,170,307

f.

Read the Data List.

Result:
Result Proceed to
Any of "Hybrid Battery Block 1, 2, 9, 10, 11 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7, 8 Voltage" is 24.0 V or less A
Other than above B



g.

Turn the power switch off.



A

B

14.CLEAR DTC
11.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

12.CHECK ENGINE START
12.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

NOTICE:

Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.


HINT:

Depressing the accelerator pedal with shift lever in P will cause the engine to start.


Result:
Result Proceed to
The engine does not start. A
The engine starts. B



c.

Turn the power switch off.



A

13.CHECK HV BATTERY

B

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

13.CHECK HV BATTERY
a.

Turn the power switch off.


b.

Wait 10 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 11 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
Hybrid Battery Block 10 Voltage
Hybrid Battery Block 11 Voltage
50003 397 161,162,163,164,165,166,167,168,169,170,307

f.

Read the Data List.

Result:
Result Proceed to
Any of "Hybrid Battery Block 1, 2, 9, 10, 11 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7, 8 Voltage" is 24.0 V or less A
Other than above B



g.

Turn the power switch off.



A

B

15.CLEAR DTC