Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2019.02
RM3620E _58 Vehicle Interior _076039 PRE-COLLISION _0369995 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U030051  Internal Control Module Software Incompatibility Not Programmed  U030057  Internal Control Module Software Incompatibility Invalid / Incompatible Software Component  


DESCRIPTION

for HV Model:
·

The forward recognition camera receives vehicle information (Conv/HV) from the hybrid vehicle control ECU via the CAN communication line.

·

When the forward recognition camera is unable to determine the vehicle information (Conv/HV) from the vehicle information (Conv/HV) sent from the hybrid vehicle control ECU, the forward recognition camera outputs U030051.

·

When the vehicle information (Conv/HV) sent from the hybrid vehicle control ECU does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.


for Gasoline Model:
·

The forward recognition camera receives vehicle information (Conv/HV) from the ECM via the CAN communication line.

·

When the forward recognition camera is unable to determine the vehicle information (Conv/HV) from the vehicle information (Conv/HV) sent from the ECM, the forward recognition camera outputs U030051.

·

When the vehicle information (Conv/HV) sent from the ECM does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.


DTC No. Detection Item DTC Detection Condition Trouble Area
U030051 Internal Control Module Software Incompatibility Not Programmed
for HV Model:

Once 3 seconds elapse after turning the ignition switch to ON, the system is unable to determine the vehicle information (Conv/HV) sent from the hybrid vehicle control ECU and vehicle information (Conv/HV) sent from the forward recognition camera for approximately 3 seconds or more


for Gasoline Model:

Once 3 seconds elapse after turning the ignition switch to ON, the system is unable to determine the vehicle information (Conv/HV) sent from the ECM and vehicle information (Conv/HV) sent from the forward recognition camera for approximately 3 seconds or more


for HV Model:
·

Hybrid control system

·

Forward recognition camera


for Gasoline Model:
·

SFI system

·

Forward recognition camera


U030057 Internal Control Module Software Incompatibility Invalid / Incompatible Software Component
for HV Model:

Once 3 seconds elapse after turning the ignition switch to ON, the vehicle information (Conv/HV) sent from the hybrid vehicle control ECU does not match the vehicle information stored by the forward recognition camera for approximately 1 second or more


for Gasoline Model:

Once 3 seconds elapse after turning the ignition switch to ON, the vehicle information (Conv/HV) sent from the ECM does not match the vehicle information stored by the forward recognition camera for approximately 1 second or more


for HV Model:
·

Hybrid control system

·

Forward recognition camera


for Gasoline Model:
·

SFI system

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


·

for HV Model:

When replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

for Gasoline Model:

When replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check vehicle condition.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)

B

5.CHECK FOR DTC (SFI SYSTEM)
2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)
a.

Check the DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

If the pre-collision system outputs U030051 or U030057, hybrid control system DTCs may also have been output. Check the hybrid control system first.


OK:

Hybrid control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC (HEALTH CHECK)

NG

3.CHECK FOR DTC (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

OK:

ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the hybrid vehicle control ECU.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS

NG

4.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Conv/HV) Vehicle information (Conv/HV) Unknown, Conv, HV - -
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Conv/HV)
50003 432 24
HINT:
·

When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.

·

When the specification stored by the forward recognition camera and the vehicle specification match, a hybrid vehicle control ECU with different specifications may be installed. Therefore, replace the hybrid vehicle control ECU.




Result:
Result Proceed to
Specification stored by the forward recognition camera and vehicle specification do not match A
"Unknown" is displayed
Specification stored by the forward recognition camera and vehicle specification match B



A

REPLACE FORWARD RECOGNITION CAMERA

B

5.CHECK FOR DTC (SFI SYSTEM)
a.

Check the DTCs.

for A25A-FKS with Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

for A25A-FKS without Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

for M20A-FKS:

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If the pre-collision system outputs U030051 or U030057, SFI system DTCs may also have been output. Check the SFI system first.


OK:

SFI system DTCs are not output.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR DTC (HEALTH CHECK)

NG

6.CHECK FOR DTC (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

OK:

ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the ECM.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

7.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Conv/HV) Vehicle information (Conv/HV) Unknown, Conv, HV - -
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Conv/HV)
50003 432 24
HINT:
·

When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.

·

When the specification stored by the forward recognition camera and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.




Result:
Result Proceed to
Specification stored by the forward recognition camera and vehicle specification do not match A
"Unknown" is displayed
Specification stored by the forward recognition camera and vehicle specification match B



A

REPLACE FORWARD RECOGNITION CAMERA

B