Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › 2019.02–2020.05
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser function compares the ID code that is registered to the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

WIRING DIAGRAM

B537420E05
5.302,2.865 7.042,3.229 1.74,0.365 10 false Hybrid Vehicle Control ECU Assembly 6.656,1.604 7.115,1.802 0.458,0.198 10 false +B 5.417,0.615 5.875,0.813 0.458,0.198 10 false IMO 5.438,1.771 5.896,1.969 0.458,0.198 10 false IMI 4.719,0.51 5.177,0.708 0.458,0.198 10 false 23 4.708,1.688 5.167,1.885 0.458,0.198 10 false 10 1.698,0.594 2.156,0.792 0.458,0.198 10 false EFII 1.635,1.771 2.094,1.969 0.458,0.198 10 false EFIO 2.052,0.604 2.51,0.802 0.458,0.198 10 false 3 2.052,1.771 2.51,1.969 0.458,0.198 10 false 4 0.729,0.146 1.188,0.344 0.458,0.198 10 false +B 0.323,2.833 0.781,3.031 0.458,0.198 10 false G57 0.333,3.021 2.625,3.427 2.292,0.406 10 false ID Code Box (Immobiliser Code ECU) 5.104,0.5 5.563,0.698 0.458,0.198 10 false 23 5.094,1.688 5.552,1.885 0.458,0.198 10 false 10 4.667,0.708 5.125,0.906 0.458,0.198 10 false G63 4.656,1.875 5.115,2.073 0.458,0.198 10 false G63 5.063,0.698 5.521,0.896 0.458,0.198 10 false A30 5.063,1.865 5.521,2.063 0.458,0.198 10 false A30 5.094,2.125 5.406,2.323 0.313,0.198 10 false *1 5.125,0.938 5.438,1.135 0.313,0.198 10 false *1 4.698,0.938 5.01,1.135 0.313,0.198 10 false *2 4.719,2.115 5.031,2.313 0.313,0.198 10 false *2 2.917,3.208 4.604,3.406 1.688,0.198 10 false *1: for LHD 2.927,3.479 4.615,3.677 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ID code box (immobiliser code ECU) or hybrid vehicle control ECU assembly, refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS

B

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts within 5 seconds of the power switch being turned on (READY).

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI AND IMO)
3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

C408269C03
4.5,0.104 4.875,0.333 0.375,0.229 5.25,0.115 5.625,0.344 0.375,0.229 5.604,2.198 5.427,2.198 5.427,2.198 4.781,0.979 true 4.281,2.052 4.417,2.052 4.417,2.052 4.719,0.896 true 3.406,4.198 3.177,4.198 3.177,4.198 3.177,3.646 false 2.771,4.198 2.99,4.198 2.99,4.198 2.99,3.646 false 3.823,6.135 3.594,6.135 3.594,6.135 3.594,5.688 false 3.625,6.302 3.396,6.302 3.396,6.302 3.396,5.698 false 0.625,0.24 0.906,0.448 0.281,0.208 10 false *a 2.594,4.135 2.906,4.292 0.313,0.156 10 false *b 3.469,4.125 3.781,4.281 0.313,0.156 10 false *c 1.854,7.125 2.167,7.281 0.313,0.156 10 false *d 1.938,7.365 2.25,7.521 0.313,0.156 10 false *e 1.313,2.479 1.625,2.635 0.313,0.156 10 false *f 1.302,4.51 1.615,4.667 0.313,0.156 10 false *g 2.458,4.635 2.771,4.792 0.313,0.156 10 false *h 3.042,2.677 3.354,2.833 0.313,0.156 10 false *i 3.469,4.635 3.781,4.792 0.313,0.156 10 false *j 1.448,6.5 1.76,6.656 0.313,0.156 10 false *k 4.594,0.135 5.031,0.385 0.438,0.25 10 false A30 5.667,2.125 6.104,2.375 0.438,0.25 10 false IMO 4.083,1.969 4.521,2.219 0.438,0.25 10 false IMI 1.052,3.625 1.563,3.917 0.51,0.292 10 false GND 1.052,5.656 1.563,5.948 0.51,0.292 10 false GND 3.865,6.073 4.177,6.229 0.313,0.156 10 false *c 3.667,6.24 3.979,6.396 0.313,0.156 10 false *b 3.177,6.5 3.49,6.656 0.313,0.156 10 false *k 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 3.677,7.365 3.99,7.521 0.313,0.156 10 false *e 4.917,0.135 5.354,0.385 0.438,0.25 10 false *A 5.313,0.135 5.75,0.385 0.438,0.25 10 false G63 5.677,0.146 6.115,0.396 0.438,0.25 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f IMO Waveform
*g IMI Waveform *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
for LHD
Tester Connection Condition Tool Setting Specified Condition
A30-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform B)
A30-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform A and C)

for RHD
Tester Connection Condition Tool Setting Specified Condition
G63-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform B)
G63-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform A and C)



Result:
Result Proceed to
Normal waveform A
Waveform A is not output, or has abnormal wavelength or shape B
Waveform B is not output, or has abnormal wavelength or shape C
Waveform C is not output, or has abnormal wavelength or shape D



A

4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

C

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

D

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Register the ECU communication ID codes.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID WAS NOT REGISTERED)

NG

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the G57 ID code box (immobiliser code ECU) connector.


b.

for LHD:

Disconnect the A30 hybrid vehicle control ECU assembly connector.


c.

for RHD:

Disconnect the G63 hybrid vehicle control ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G57-3 (EFII) - A30-23 (IMO) Always Below 1 Ω
G57-4 (EFIO) - A30-10 (IMI) Always Below 1 Ω
G57-3 (EFII) or A30-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher
G57-4 (EFIO) or A30-10 (IMI) - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G57-3 (EFII) - G63-23 (IMO) Always Below 1 Ω
G57-4 (EFIO) - G63-10 (IMI) Always Below 1 Ω
G57-3 (EFII) or G63-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher
G57-4 (EFIO) or G63-10 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG