Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P106A62  Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure  P106C62  Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure  


DESCRIPTION

Those DTCs are designed to detect a deviation in the output characteristics of a pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P106A62 Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold absolute pressure sensor (Intake Manifold Absolute Pressure*) is higher than 8.69 kPa (1.26 psi) (2 trip detection logic).
·

Canister pressure sensor (canister pump module)

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P106A
P106C62 Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and atmospheric pressure sensor (Atmospheric Pressure*) is Higher than 7.89 kPa (1.14 psi) (2 trip detection logic).
·

Canister pressure sensor (canister pump module)

·

Atmospheric pressure sensor (ECM)


Comes on DTC stored SAE Code: P106C

*: Data List name

MONITOR DESCRIPTION

Those DTCs are stored when a deviation from pressure sensor characteristics is detected.

The pressure sensors* are checked approximately 50 minutes after the power switch is turned off. If the pressures detected by the pressure sensors* differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).

HINT:
·

*: P106A62 checks the canister pressure sensor and the manifold absolute pressure sensor. P106C62 checks the canister pressure sensor and atmospheric pressure sensor.

·

Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.



MONITOR STRATEGY

Required Sensors/Components Canister pressure sensor
Atmospheric pressure sensor (ECM)
Manifold absolute pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and idle for 10 seconds or more [A].

10.

Turn the power switch off.

11.

Leave the power switch off for 55 minutes [B].

12.

Turn the power switch on (IG).

13.

Turn the GTS on.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P106A62 or P106C62.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

Refer to "Data List / Active Test" [Atmospheric Pressure, Intake Manifold Absolute Pressure and Vapor Pressure Pump].

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P106A62 AND/OR P106C62)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P106A62 is output A
DTC P106C62 is output B
DTC P106A62 and P106C62 are output C
DTC P106A62 and/or P106C62 and other DTCs are output D


HINT:

If any DTCs other than P106A62 and/or P106C62 are output, troubleshoot those DTCs first.




A

2.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

B

3.REPLACE ECM (ATMOSPHERIC PRESSURE SENSOR)

C

4.REPLACE CANISTER PUMP MODULE

D

2.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>A25A-FXS (EMISSION CONTROL)>VACUUM SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
3.REPLACE ECM (ATMOSPHERIC PRESSURE SENSOR)
a.

Replace the ECM (atmospheric pressure sensor).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
4.REPLACE CANISTER PUMP MODULE

Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure, Vapor Pressure Pump and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Intake Manifold Absolute Pressure
Vapor Pressure Pump
50003 372 229,385,160

e.

Confirm that the difference between Intake Manifold Absolute Pressure and Vapor Pressure Pump is 8.69 kPa (1.26 psi) or less.


f.

Confirm that the difference between Atmospheric Pressure and Vapor Pressure Pump is 7.89 kPa (1.14 psi) or less.


Result:
Proceed to
NEXT



NEXT

END