Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P12D013  Fuel Pump Control (All Phase) Circuit Open  P12D113  Fuel Pump Control (U Phase) Circuit Open  P12D213  Fuel Pump Control (V Phase) Circuit Open  P12D313  Fuel Pump Control (W Phase) Circuit Open  


DESCRIPTION

Refer to DTC P062712.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P062712

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P12D013 Fuel Pump Control (All Phase) Circuit Open When the fuel pump control ECU operation duty ratio is 3 to 65%, an open is detected in the FPU, FPV and FPW circuit for 3 seconds or more (2 trip detection logic).
·

Open in fuel pump control ECU circuit

·

Fuel pump control ECU

·

Fuel pump (for low pressure side)


Comes on DTC stored SAE Code: P12D0
P12D113 Fuel Pump Control (U Phase) Circuit Open When the fuel pump control ECU operation duty ratio is 3 to 65%, an open is detected in the FPU circuit for 3 seconds or more (2 trip detection logic).
·

Open in fuel pump control ECU circuit

·

Fuel pump control ECU

·

Fuel pump (for low pressure side)


Comes on DTC stored SAE Code: P12D1
P12D213 Fuel Pump Control (V Phase) Circuit Open When the fuel pump control ECU operation duty ratio is 3 to 65%, an open is detected in the FPV circuit for 3 seconds or more (2 trip detection logic).
·

Open in fuel pump control ECU circuit

·

Fuel pump control ECU

·

Fuel pump (for low pressure side)


Comes on DTC stored SAE Code: P12D2
P12D313 Fuel Pump Control (W Phase) Circuit Open When the fuel pump control ECU operation duty ratio is 3 to 65%, an open is detected in the FPW circuit for 3 seconds or more (2 trip detection logic).
·

Open in fuel pump control ECU circuit

·

Fuel pump control ECU

·

Fuel pump (for low pressure side)


Comes on DTC stored SAE Code: P12D3

Related Data List
DTC No. Data List
P12D013
P12D113
P12D213
P12D313
Fuel Pump Control Duty Ratio

MONITOR DESCRIPTION

The fuel pump control ECU monitors the fuel pump drive circuit.

When a malfunction is detected in the fuel pump drive circuit, the diagnosis output circuit in the fuel pump control ECU modifies the operation signal sent by the ECM to indicate that there is a malfunction.

When the fuel pump control ECU operation duty ratio is 3 to 65% and the FPU, FPV or FPW terminal voltage is less than a certain value for 3 seconds or more, the diagnosis output circuit in the fuel pump control ECU modifies the operation signal sent by the ECM to indicate that there is a malfunction, and the ECM stores a DTC.

A404864E02
6.479,3.844 6.969,4.125 0.49,0.281 10 false ECM 6.219,2.26 6.677,2.458 0.458,0.198 10 false FPC 2.573,5.385 4.26,5.698 1.688,0.313 10 false Fuel Pump Control ECU 5.563,1.906 5.875,2.104 0.313,0.198 10 false *1 5.563,2.792 5.875,2.99 0.313,0.198 10 false *2 2.969,2.5 4.167,2.99 1.198,0.49 10 false Fuel Pump Control Circuit 3.052,3.688 3.927,4.208 0.875,0.521 10 false Diagnosis Output Circuit 1.917,2.125 2.677,2.531 0.76,0.406 10 false Fuel Pump Drive Circuit 0.135,3.875 1.354,4.292 1.219,0.417 10 false Fuel Pump (for Low Pressure Side) 1.479,1.854 1.938,2.052 0.458,0.198 10 false FPU 1.49,2.385 1.948,2.583 0.458,0.198 10 false FPV 1.479,2.927 1.938,3.125 0.458,0.198 10 false FPW 4.75,2.24 5.208,2.438 0.458,0.198 10 false FPC 0.552,5.938 6.823,6.135 6.271,0.198 10 false *1: Fuel Pump Control Signal (Duty-cycle) 0.573,6.302 4.885,6.698 4.313,0.396 10 false *2: Diagnosis Output Signal (Fuel Pump Control Signal Modified) 0.854,0.438 2.542,0.74 1.688,0.302 10 false Fuel Pump Drive Circuit

MONITOR STRATEGY

Required Sensors/Components Fuel pump control ECU
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and wait 10 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P12D013, P12D113, P12D213 or P12D313.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, run the engine at an engine speed of 2500 rpm or more for 10 seconds or more and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
A402441C28
2.708,0.281 3.094,0.531 0.385,0.25 2.031,2.323 2.479,1.479 true 2.677,2.302 2.708,1.49 true 3.135,2.344 2.99,1.5 true 0.177,0.104 0.49,0.302 0.313,0.198 10 false *1 2.781,0.313 3.24,0.51 0.458,0.198 10 false N14 1.802,2.365 2.25,2.656 0.448,0.292 10 false FPW 2.5,2.375 2.958,2.646 0.458,0.271 10 false FPV 3,2.396 3.479,2.646 0.479,0.25 10 false FPU
*1 Fuel Pump Control ECU - -


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the N14 fuel pump control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
N14-2 (FPU) - Body ground U Phase 4.4 to 8.4 V*
N14-3 (FPV) - Body ground V Phase 4.4 to 8.4 V*
N14-4 (FPW) - Body ground W Phase 4.4 to 8.4 V*


HINT:
·

*: This Active Test limits the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage (+B terminal).

·

Before performing this inspection, check that the auxiliary battery voltage is between 11 and 14 V (not depleted).




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))

NG

REPLACE FUEL PUMP CONTROL ECU

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the fuel pump (for low pressure side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-2 (FPU) - N46-3 (BLPU) Always Below 1 Ω
N14-3 (FPV) - N46-4 (BLPV) Always Below 1 Ω
N14-4 (FPW) - N46-2 (BLPW) Always Below 1 Ω



Result:
Proceed to
OK
NG


HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR