Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2019.02–2020.05
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P019511  Engine Oil Temperature Sensor Circuit Short to Ground  


DESCRIPTION

A422247E01
0.115,0.094 3.01,0.521 2.896,0.427 10 false Characteristics of Oil Temperature Sensor: 0.125,0.656 0.885,0.885 0.76,0.229 10 false Voltage [V] 1.177,3.094 2.385,3.323 1.208,0.229 10 false Temperature 0.229,1.083 0.76,1.313 0.531,0.229 10 false 4.500 0.208,1.802 0.594,2.021 0.385,0.219 10 false 2.064 0.208,2.073 0.594,2.292 0.385,0.219 10 false 1.379 0.208,2.229 0.594,2.448 0.385,0.219 10 false 1.000 0.583,2.479 0.844,2.708 0.26,0.229 10 false -30 0.896,2.479 1.156,2.708 0.26,0.229 10 false -10 1.531,2.5 1.792,2.729 0.26,0.229 10 false 25 2.521,2.51 2.823,2.75 0.302,0.24 10 false 140 2.958,2.51 3.26,2.75 0.302,0.24 10 false [°C] 2.958,2.792 3.26,3.031 0.302,0.24 10 false [°F] 0.573,2.781 0.833,3.01 0.26,0.229 10 false -22 0.927,2.781 1.188,3.01 0.26,0.229 10 false 14 1.542,2.802 1.802,3.031 0.26,0.229 10 false 77 2.531,2.802 2.833,3.042 0.302,0.24 10 false 284

The engine oil temperature sensor (oil pressure and temperature sensor) replaces the oil temperature with electrical signals and outputs them to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P019511 Engine Oil Temperature Sensor Circuit Short to Ground The engine oil temperature sensor output voltage is less than 0.13 V for 5 seconds or more (1 trip detection logic).
·

Short in engine oil temperature sensor circuit

·

Engine oil temperature sensor (oil pressure and temperature sensor)

·

ECM


Does not come on DTC stored SAE Code: P0197

HINT:

When this DTC is output, check the engine oil temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.

DTC No. Engine Oil Temperature Sensor Malfunction
P019511 -40°C (-40°F)
·

Short to ground in THEO circuit

·

Short in EPEO to THEO circuit

·

Open in VCPE circuit



If the Data List values are normal, it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>CHECK FOR INTERMITTENT PROBLEMS


MONITOR DESCRIPTION

The ECM monitors the engine oil temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor (oil pressure and temperature sensor) circuit is malfunctioning and stores this DTC.

Example:

If the engine oil temperature sensor output voltage is less than 0.535 V for 5 seconds or more, the ECM will store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Wait 10 seconds or more [B].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P019511.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A403505E52
0.156,2.906 0.615,3.104 0.458,0.198 10 false C5 0.167,3.063 2.365,3.438 2.198,0.375 10 false Engine Oil Temperature Sensor (Oil Pressure and Temperature Sensor) 1.406,1.021 1.719,1.219 0.313,0.198 10 false VC 1.729,0.906 1.885,1.104 0.156,0.198 10 false 3 1.25,1.719 1.813,1.948 0.563,0.229 10 false TOUT 1.729,1.604 1.885,1.802 0.156,0.198 10 false 4 1.302,2.49 1.708,2.688 0.406,0.198 10 false GND 1.74,2.385 1.896,2.583 0.156,0.198 10 false 2 4.365,0.927 4.677,1.125 0.313,0.198 10 false 99 4.281,1.604 4.74,1.802 0.458,0.198 10 false 123 4.292,2.406 4.604,2.604 0.313,0.198 10 false 100 4.604,0.917 5.167,1.208 0.563,0.292 10 false VCPE 4.646,1.604 5.104,1.802 0.458,0.198 10 false THEO 4.625,2.385 5.24,2.583 0.615,0.198 10 false EPEO 5.604,0.688 6.063,0.885 0.458,0.198 10 false 5 V 5.292,3.26 5.719,3.542 0.427,0.281 10 false ECM 5.302,1.417 5.917,1.615 0.615,0.198 10 false 180 kΩ 5.292,3.094 5.719,3.375 0.427,0.281 10 false C45

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A373523C62
0.302,1.052 0.656,1.302 0.354,0.25 2.031,1.115 2.583,1.781 true 1.063,1.75 1.573,1.208 true 1.833,1.771 1.802,1.208 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.396,1.094 0.708,1.292 0.313,0.198 10 false C5 2.49,1.823 2.948,2.042 0.458,0.219 10 false TOUT 0.906,1.802 1.281,2.042 0.375,0.24 10 false GND 1.76,1.823 2.073,2.021 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Engine Oil Temperature Sensor (Oil Pressure and Temperature Sensor))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the engine oil temperature sensor (oil pressure and temperature sensor) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C5-3 (VC) - C5-2 (GND) Power switch on (IG) 4.5 to 5.5 V
C5-4 (TOUT) - C5-2 (GND) Power switch on (IG) 3.0 to 5.5 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C5-3 (VC) - C5-4 (TOUT) Power switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE OIL TEMPERATURE SENSOR (OIL PRESSURE AND TEMPERATURE SENSOR)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR (OIL PRESSURE AND TEMPERATURE SENSOR) - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR (OIL PRESSURE AND TEMPERATURE SENSOR) - ECM)
a.

Disconnect the engine oil temperature sensor (oil pressure and temperature sensor) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-3 (VC) - C45-99 (VCPE) Always Below 1 Ω
C5-4 (TOUT) or C45-123 (THEO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR