Home › Power Source / Network › A25A-FKS (BATTERY / CHARGING) › GENERATOR(for 150 A Type) › from 2019.09
RM3620E _57 Power Source / Network _076183 A25A-FKS BATTERY / CHARGING _0371284 GENERATOR(for 150 A Type) A

A25A-FKS BATTERY / CHARGING  GENERATOR(for 150 A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A431997E01
0.969,1.25 0.458,0.375 0.458,0.375 1.052,0.542 true 2.615,0.875 2.99,0.396 2.99,0.396 2.458,0.656 true 0.167,0.292 0.625,0.49 0.458,0.198 10 false SST 3.021,0.292 3.354,0.49 0.333,0.198 10 false SST

Using SST and a press, install a new generator drive end frame bearing.

SST
09950-60011  (09951-00470)
09950-70010  (09951-07100)


b.
A431998C01
2.635,1.917 2.865,1.25 true 1.917,0.198 2.094,0.198 2.094,0.198 2.885,0.885 true 1.74,0.104 2.052,0.26 0.313,0.156 10 false *a 2.542,1.938 2.854,2.094 0.313,0.156 10 false *b
*a Tab
*b Cutout


Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.
A401891C01
0.51,0.344 0.698,0.344 0.698,0.344 1.125,0.635 false 2.635,1.802 2.635,1.438 false 0.365,0.26 0.677,0.417 0.313,0.156 10 false *1 2.573,1.813 2.885,1.969 0.313,0.156 10 false *2
*1 Generator Rotor Assembly
*2 Generator Drive End Frame


Install the generator rotor assembly to the generator drive end frame.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A284134

for Type A:

Place a new washer on the generator rotor assembly.


b.
A401901C01
1.927,0.49 2.417,0.49 true 1.927,1.458 2.417,1.458 true 2.438,0.406 2.75,0.563 0.313,0.156 10 false *a 2.438,1.365 2.75,1.521 0.313,0.156 10 false *b
*a Protrusion
*b Groove


for Type B:

Install a new bearing cover packing.

NOTICE:

Align the protrusions of the bearing cover packing with the grooves of the generator coil assembly when installing.



c.
A401892C01
0.615,0.542 1.208,0.542 false 2.052,0.156 2.208,0.156 2.208,0.156 2.49,0.427 true 0.469,0.448 0.781,0.604 0.313,0.156 10 false *a 1.906,0.052 2.219,0.208 0.313,0.156 10 false *a
*a 21 mm Deep Socket Wrench


Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


d.
A431999

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370A 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C22
2.479,0.74 1.979,0.198 1.979,0.198 1.729,0.198 false 0.917,0.521 0.708,0.198 0.708,0.198 0.458,0.198 false 1.521,0.094 1.833,0.313 0.313,0.219 10 false *a 0.271,0.104 0.583,0.323 0.313,0.219 10 false *a
*a Pin (1.0 mm)


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


b.
A432000C01
1.74,1 2.281,1.344 true 2.302,1.313 2.5,1.552 0.198,0.24 10 true *a
*a Pin (1.0 mm)
V100136

Pull out


for Type A:

i.

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


ii.

Pull out the pin from the generator brush holder assembly hole.



c.

for Type B:

i.

Install the generator brush holder assembly to the generator coil assembly with the 3 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


ii.

Pull out the pin from the generator brush holder assembly hole.



Hide 27387B 5.INSTALL GENERATOR TERMINAL INSULATOR

A432001

a.

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct orientation.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

A432002

a.

for Type A:

Install the generator rear end cover to the generator coil assembly with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


b.

for Type B:

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.

Temporarily install a new generator pulley with clutch to the rotor shaft.


c.
A284135E23
1.354,0.646 1.052,0.354 1.052,0.354 0.813,0.354 false 2.344,0.875 2.073,0.875 2.073,0.875 1.76,1.417 false 0.281,0.281 0.865,0.531 0.583,0.25 10 false SST (A) 2.417,0.802 2.969,1.073 0.552,0.271 10 false SST (B)

Install SST (A) to SST (B) as shown in the illustration.

SST
09820-63021  


d.
A432003C01
1.281,0.552 1.594,0.26 1.594,0.26 1.719,0.26 true 0.323,1.469 0.323,0.854 true 1.76,1.208 1.76,1.01 true 1.74,0.177 2.052,0.333 0.313,0.156 10 false *a 0.083,1.531 0.854,1.802 0.771,0.271 10 false SST (A) 1.521,1.24 2.083,1.385 0.563,0.146 10 true SST (A)
*a Rotor Shaft


Fit the rotor shaft end into SST (A).


e.
A432004C01
1.104,0.365 1.302,0.167 1.302,0.167 1.438,0.167 true 0.406,1.604 0.406,1.083 true 1.5,1.552 1.646,1.552 1.646,1.552 1.979,0.958 true 1.479,0.083 1.792,0.24 0.313,0.156 10 false *1 0.177,1.635 0.948,1.833 0.771,0.198 10 false SST (B) 0.969,1.479 1.74,1.677 0.771,0.198 10 false SST (B)
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.


f.
A432005C01
0.573,1.042 0.854,1.042 false 0.656,0.396 0.844,0.396 0.844,0.396 1.135,0.875 false 1.542,2 1.781,2.208 0.24,0.208 10 true *a 2.396,1.24 2.708,1.396 0.313,0.156 10 true *b 1.042,2.521 1.354,2.677 0.313,0.156 10 false *c 0.125,0.313 0.896,0.51 0.771,0.198 10 false SST (B) 0.042,0.958 0.813,1.156 0.771,0.198 10 false SST (A)
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (1.312 ft.)): 64 N*m (653 kgf*cm, 47 ft.*lbf)




g.

Remove SST (A) and (B) from the generator pulley with clutch.


h.

Check that the generator pulley with clutch rotates smoothly.


i.

Remove the generator drive end frame from the vise.


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.