Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING VALVE › 2019.09–2020.05
RM3620E _53 Suspension _076850 TIRE PRESSURE MONITORING _0377452 TIRE PRESSURE WARNING VALVE A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the Tire pressure warning valve and transmitter removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Tire pressure warning valve and transmitter
·

Register transmitter ID

·

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC are met, tire pressure warning light blinks for 1 minute, and then illuminates

·

Tire pressure warning function


for Initialization:(Click here)
for Registration:(Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Tire pressure warning valve and transmitter
·

Register transmitter ID

·

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC are met, tire pressure warning light blinks for 1 minute, and then illuminates

·

Tire pressure warning function


for Initialization:(Click here)
for Registration:(Click here)

PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.REMOVE REAR WHEEL

Hide 3.REMOVE FULL SIZE SPARE TIRE (w/ Full Size Spare Tire)

Hide 42607 4.REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type A)

a.

Remove the tire valve cap.

NOTICE:

Keep the removed tire valve cap.



b.

Remove the valve core to release the air from the tire.

NOTICE:

Make sure that a sufficient amount of air has been released.



c.
C180021C06
0.531,0.885 0.979,0.885 false 2.427,0.885 2.958,0.885 false 0.302,0.823 0.604,1.01 0.302,0.188 10 false *1 2.99,0.833 3.302,0.99 0.313,0.156 10 false *a 2.094,1.781 2.406,1.938 0.313,0.156 10 false *b
*1 Tire
*a Shoe
*b 10 to 20 mm (0.394 to 0.787 in.)


Using a tire remover, remove the tire from the disc wheel.

NOTICE:
·

Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.

·

Set the tire remover shoe as shown in the illustration.




d.
C402143

Using a T10 "TORX" socket wrench, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.


e.
C402144C01
0.458,2.354 1,2.354 false 0.271,2.281 0.583,2.479 0.313,0.198 10 false *1
*1 Tubeless Tire Valve
V100155

Cutting Area


Cut the tubeless tire valve and remove it by pulling from the outer side of the disc wheel as shown in the illustration.


Hide 42607 5.REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type B)

a.

Remove the tire valve cap and valve core to release the air from the tire.

NOTICE:

Keep the removed tire valve cap.



b.

After ensuring that a sufficient amount of air has been released, remove the nut and washer used to secure the tire pressure warning valve and transmitter. Then drop the tire pressure warning valve and transmitter with the grommet into the tire.

HINT:

The grommet may remain attached to the rim.



c.
C180021C11
0.531,0.885 0.979,0.885 false 2.427,0.885 2.958,0.885 false 0.396,0.781 0.698,0.969 0.302,0.188 10 false *1 3.01,0.781 3.323,0.938 0.313,0.156 10 false *a 2.094,1.771 2.406,1.927 0.313,0.156 10 false *b
*1 Tire
*a Shoe
*b 10 to 20 mm (0.394 to 0.787 in.)


After dropping the tire pressure warning valve and transmitter into the tire, disengage the bead using the shoe of a tire remover.

NOTICE:
·

Be careful as the tire pressure warning valve and transmitter may become damaged due to interference between the sensor and tire bead.

·

Set the tire remover shoe as shown in the illustration.




d.

Separate the upper bead.


e.

Take out the tire pressure warning valve and transmitter with the grommet from the tire and separate the lower bead.


f.

Remove the grommet from the tire pressure warning valve and transmitter.


Hide 42607 6.REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type C)

a.

Remove the tire valve cap.

NOTICE:

Keep the removed tire valve cap.



b.

Remove the valve core to release the air from the tire.

NOTICE:

Make sure that a sufficient amount of air has been released.



c.

Using a 11 mm deep socket wrench, remove the nut and washer.


d.

Drop the tire pressure warning valve and transmitter with grommet into the tire.

HINT:

The grommet may remain attached to the rim.



e.
C180021C11
0.531,0.885 0.979,0.885 false 2.427,0.885 2.958,0.885 false 0.396,0.781 0.698,0.969 0.302,0.188 10 false *1 3.01,0.781 3.323,0.938 0.313,0.156 10 false *a 2.094,1.771 2.406,1.927 0.313,0.156 10 false *b
*1 Tire
*a Shoe
*b 10 to 20 mm (0.394 to 0.787 in.)


Using a tire remover, remove the tire from the disc wheel.

NOTICE:
·

Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.

·

Set the tire remover shoe as shown in the illustration.




f.

Take out the tire pressure warning valve and transmitter with grommet from the tire.


g.

Remove the grommet from the tire pressure warning valve and transmitter.


h.
C411111

Using a T10 "TORX" socket wrench, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.