Always use a new bolt, tubeless tire valve and valve core when installing the tire pressure warning valve and transmitter.
Make sure not to damage the urethane covered backside of the tire pressure warning valve and transmitter (the surface opposite to the side with the ID code) with anything sharp.
Write down the ID number before installation.
Check that there is no oil, water or lubricant around the rim hole and tire pressure warning valve and transmitter. Failing to do so may result in improper installation.
Use only a specified tire valve cap. If an unspecified tire valve cap is used, it may seize to the tire pressure warning valve and transmitter.
| *A | for Type A |
| *a | Rubber Tubeless Tire Valve |
The tire pressure warning valve and transmitter (for type A) cannot be installed to steel wheels. Make sure to check the wheel type before installation.
Always use a new grommet and valve core when installing the tire pressure warning valve and transmitter.
Check that the washer and nut are not damaged, and replace it if necessary.
Make sure not to damage the urethane covered backside of the tire pressure warning valve and transmitter (the surface opposite to the side with the ID code) with anything sharp.
Write down the ID number before installation.
Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, washer and nut. Failing to do so may result in improper installation.
Use only a specified tire valve cap. If an unspecified tire valve cap is used, it may seize to the tire pressure warning valve and transmitter.
Always use a new bolt, grommet, tubeless tire valve and valve core when installing the tire pressure warning valve and transmitter.
Check that the washer and nut are not damaged, and replace them if necessary.
Make sure not to damage the urethane covered backside of the tire pressure warning valve and transmitter (the surface opposite to the side with the ID code) with anything sharp.
Write down the ID number before installation.
Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, washer and nut. Failing to do so may result in improper installation.
Use only a specified tire valve cap. If an unspecified tire valve cap is used, it may seize to the tire pressure warning valve and transmitter.
42607
1.INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type A)
Using a T10 "TORX" socket wrench, install the tire pressure monitor sensor to the new tubeless tire valve with a new bolt.
| *a | Printed Surface |
| *b | 7-digit Transmitter ID Number |
Write down the 7-digit transmitter ID number shown in the illustration.
| *1 | Tire Pressure Warning Valve and Transmitter |
| *a | Rim |
Install the tire pressure warning valve and transmitter from the inside of the rim.
Make sure that the tire pressure warning valve and transmitter is installed so that the printed surface can be seen. If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.
Check that there is no deformation or damage to the tire pressure warning valve and transmitter.
Check that there is no foreign matter on the around the rim hole.
| *a | Mount Tool of the Mounting Machine |
| *b | 60° |
| *c | Rim |
|
Rim Rotating Direction |
|
Area for Tire Pressure Warning Valve and Transmitter |
Set the tire and disc wheel onto the mounting machine as shown in the illustration.
Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.
If the tire pressure warning valve and transmitter is positioned outside this area, it will interfere with the tire bead and may be damaged.
Apply a sufficient coat of soapy water or equivalent to the tire bead and rim.
Do not apply soapy water or equivalent directly to the tire pressure warning valve and transmitter.
Using a mounting machine, install the tire to the disc wheel.
Make sure that the tire bead and mount tool do not interfere with the tire pressure warning valve and transmitter.
Make sure that the tire pressure warning valve and transmitter is not clamped by the bead and rim.
Install a new valve core.
Inflate the tire to the specified tire inflation pressure.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Check the surroundings of the tire pressure warning valve and transmitter for air leaks with soapy water or equivalent.
If air is leaking from the valve core, press the valve core several times to remove foreign matter. Replace the valve core as necessary.
If air is leaking from around the tire pressure warning valve and transmitter, check if the tubeless tire valve is not deformed, damaged or contaminated with foreign matter. Replace the tubeless tire valve as necessary.
Install the tire valve tire valve cap.
42607
2.INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type B)
Install a new grommet to the tire pressure warning valve and transmitter.
A new tire pressure warning valve and transmitter comes with a grommet installed. Make sure not to install an extra grommet.
| *a | Printed Surface |
| *b | 7-digit Number Transmitter ID |
Record the 7-digit number transmitter ID printed on the tire pressure warning valve and transmitter at the position shown in the illustration.
Insert the tire pressure warning valve and transmitter into the valve installation hole from the inside of the rim so that the printed surface can be seen.
Check that there is no visible deformation, damage, or other abnormalities on the tire pressure warning valve and transmitter.
Check that there is no foreign matter on the grommet and around the rim hole.
If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.
| *1 | Tire Pressure Warning Valve and Transmitter |
| *2 | Rim |
| *3 | Grommet |
| *4 | Washer |
| *5 | Nut |
From the outside of the rim, install the washer to the tire pressure warning valve and transmitter, which has the grommet installed. Afterward, using an 11 mm deep socket wrench, tighten the nut.
No further tightening is required once the nut is tightened to the specified torque.
Check that there is no foreign matter on the washer and nut.
| *a | Mount Tool of the Mounting Machine |
| *b | 60° |
| *c | Rim |
|
Rim Rotating Direction |
|
Area for Tire Pressure Warning Valve and Transmitter |
Set the wheel onto a mounting machine and install the lower bead. Position the main body of the tire pressure warning valve and transmitter in the shaded area shown in the illustration.
If the tire pressure warning valve and transmitter is positioned outside this area, it will interfere with the tire bead and may be damaged.
If the use of lubricant is required when installing the bead, do not apply lubricant directly to the tire pressure warning valve and transmitter.
Install the upper bead.
Make sure that the tire bead and tool do not interfere with the main body of the tire pressure warning valve and transmitter and that it is not clamped by the bead.
Install a new valve core.
After the tire is inflated, the valve nut may be loose. Retighten the nut to the specified torque.
No further tightening is required once the nut is tightened to the specified torque.
Check for air leaks with soapy water.
If there is air leakage, push the valve core 2 or 3 times to remove any dirt attached to the valve core. If air continues to leak, replace the grommet, washer and nut.
Install the tire valve cap.
42607
3.INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type C)
Using a T10 "TORX" socket wrench, install the tire pressure monitor sensor to the new tubeless tire valve with a new bolt.
Install a new grommet to the tire pressure warning valve and transmitter.
A new tire pressure warning valve and transmitter comes with a grommet installed. Make sure not to install an extra grommet.
| *a | Printed Surface |
| *b | 7-digit Transmitter ID Number |
Write down the 7-digit transmitter ID number shown in the illustration.
| *1 | Tire Pressure Warning Valve and Transmitter |
| *2 | Grommet |
| *3 | Washer |
| *4 | Nut |
| *a | Rim |
Insert the tire pressure warning valve and transmitter with grommet from the inside of the rim.
Make sure that the tire pressure warning valve and transmitter is installed so that the printed surface can be seen. If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.
Check that there is no deformation or damage to the tire pressure warning valve and transmitter.
Check that there is no foreign matter on the grommet and around the rim hole.
Install the washer to the tire pressure warning valve and transmitter from the outside of the rim, and using a 11 mm deep socket wrench, tighten the nut.
No further tightening is required once the nut is tightened to the specified torque.
Check that there is no foreign matter on the grommet, washer and nut.
| *a | Mount Tool of the Mounting Machine |
| *b | 60° |
| *c | Rim |
|
Rim Rotating Direction |
|
Area for Tire Pressure Warning Valve and Transmitter |
Set the tire and disc wheel onto the mounting machine as shown in the illustration.
Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.
If the tire pressure warning valve and transmitter is positioned outside this area, it will interfere with the tire bead and may be damaged.
Apply a sufficient coat of soapy water or equivalent to the tire bead and rim.
Do not apply soapy water or equivalent directly to the tire pressure warning valve and transmitter.
Using a mounting machine, install the tire to the disc wheel.
Make sure that the tire bead and mount tool do not interfere with the tire pressure warning valve and transmitter.
Make sure that the tire pressure warning valve and transmitter is not clamped by the bead and rim.
Install a new valve core.
Inflate the tire to the specified tire inflation pressure.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
After the tire is inflated, the nut may be loose. Using a 11 mm deep socket wrench, retighten the nut to the specified torque.
No further tightening is required once the nut is tightened to the specified torque.
Check the surroundings of the tire pressure warning valve and transmitter for air leaks with soapy water or equivalent.
If air is leaking from the valve core, press the valve core several times to remove foreign matter. Replace the valve core as necessary.
If air is leaking from around the tire pressure warning valve and transmitter, check if the grommet, washer and nut are not deformed, damaged or contaminated with foreign matter. Replace the grommet, washer or nut as necessary.
Install the tire valve cap.
4.INSTALL FRONT WHEEL
5.INSTALL REAR WHEEL
6.INSTALL FULL SIZE SPARE TIRE (w/ Full Size Spare Tire)
7.INSPECT TIRES
8.REGISTER TRANSMITTER ID
9.INSPECT TIRE PRESSURE WARNING SYSTEM
10. PERFORM INITIALIZATION