Home › Engine / Hybrid System › A25A-FKS (STARTING) › STARTER (for 1.2 kW Type) › from 2019.09
RM3620E _51 Engine / Hybrid System _076487 A25A-FKS STARTING _0409133 STARTER(for 1.2 kW Type) A

A25A-FKS STARTING  STARTER(for 1.2 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A325110C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and pinion drive lever.

HINT:

Apply a total of approximately 0.5 g (0.0176 oz) of high-temperature grease to the planetary gears and planetary gear shafts.



b.
A248654C09
1.302,1.042 0.573,1.583 0.573,1.583 1.177,1.448 true 0.604,1.573 1.5,1.531 true 0.375,1.49 0.583,1.708 0.208,0.219 10 false *a
*a Planetary Gear Shaft


Install the 3 planetary gears to the planetary gear shafts of the starter center bearing clutch sub-assembly.


c.
A250735

Engage the 3 claws and install the starter shock absorber to the starter center bearing clutch sub-assembly.


d.
A324881C01
1.729,0.74 2.042,0.396 2.042,0.396 2.271,0.396 true 1.615,1.99 1.896,1.99 1.896,1.99 2.146,1.292 true 2.354,0.281 2.667,0.438 0.313,0.156 10 false *a 1.448,1.875 1.76,2.031 0.313,0.156 10 false *b
*a Cutout
*b Protrusion


Align the cutout of the starter drive housing assembly with the protrusion of the starter center bearing clutch sub-assembly and install the starter center bearing clutch sub-assembly.


e.
A324876

Install the rubber seal to the starter drive housing assembly.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A248658

Install the starter commutator end frame assembly to the starter brush holder assembly as shown in the illustration.

HINT:

If the parts are not aligned correctly, the through bolt cannot be attached.



b.
A248796

Spread the brushes on the starter brush holder assembly, and install the starter armature assembly to the starter brush holder assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A412086C01
1.063,0.854 1.563,0.854 false 0.792,2.417 1.24,2.417 false 2.104,2.833 2.552,2.833 false 0.906,1.26 1.073,1.26 1.073,1.26 1.635,1.813 true 0.625,2.333 0.938,2.49 0.313,0.156 10 false *1 2.563,2.75 2.875,2.906 0.313,0.156 10 false *2 0.76,1.177 1.073,1.333 0.313,0.156 10 false *3 0.896,0.76 1.208,0.917 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Brush Holder Assembly
*3 Starter Armature Assembly
*a Hammer


Install the starter yoke assembly while holding down the starter armature assembly and starter brush holder assembly with the handle of a hammer.

HINT:

The starter armature assembly will be attracted by the magnetic field of the starter yoke assembly. Hold the starter armature assembly with the handle of the hammer.



Hide 4.INSTALL STARTER YOKE ASSEMBLY

a.
A324883C01
0.906,0.719 1.083,0.25 1.083,0.25 1.365,0.25 false 1.385,0.771 1.781,1.563 1.781,1.563 2.063,1.563 false 1.458,0.135 1.771,0.292 0.313,0.156 10 false *a 2.135,1.458 2.448,1.615 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the cutout of the starter yoke assembly with the protrusion of the starter center bearing clutch sub-assembly.


b.

Using a 7 mm socket wrench, install the starter yoke assembly with the 3 through bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A324874C03
0.344,0.292 0.521,0.292 0.521,0.292 0.781,0.625 true 1.292,1.49 1.479,1.49 1.479,1.49 1.542,1.146 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *b 1.135,1.365 1.375,1.594 0.24,0.229 10 false *a
*a Hook
*b Pinion Drive Lever


Hang the hook of the magnet starter switch assembly on the pinion drive lever.


b.
A324884C01
0.615,2.208 0.792,2.208 0.792,2.208 1.125,2.542 true 0.458,2.115 0.656,2.281 0.198,0.167 10 false *a
*a Terminal C


Push down the rear of the magnet starter switch assembly and connect it to terminal C.

NOTICE:
·

Connect the magnet starter switch assembly securely to terminal C.

·

Check that the parts are free of foreign matter, oil or grease.




c.
A250021

Using a 7 mm socket wrench, install the magnet starter switch assembly with the 2 bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)