Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › from 2019.09
RM3620E _59 Vehicle Exterior _076126 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0370732 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  There is No Sound Made  


DESCRIPTION

Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly.

WIRING DIAGRAM

E402275E25
5.594,5.75 6.885,6.26 1.292,0.51 10 false Vehicle Approaching Speaker Assembly 4.5,4.948 4.958,5.146 0.458,0.198 10 false SP+ 4.51,5.24 4.969,5.438 0.458,0.198 10 false SP- 4.469,6.969 4.927,7.167 0.458,0.198 10 false GND 3.354,7.833 6.021,8.115 2.667,0.281 10 false Vehicle Approaching Speaker Controller 0.781,7.469 2.698,7.76 1.917,0.292 10 false Combination Meter Assembly 0.802,2.365 2.583,2.708 1.781,0.344 10 false Hybrid Vehicle Control ECU 0.844,4.052 2.5,4.542 1.656,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 0.688,5.75 2.74,6.333 2.052,0.583 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.938,0.896 3,1.135 1.063,0.24 10 false ECU-IG1 NO.3 0.177,0.74 1.563,0.99 1.385,0.25 10 false from IG1 NO.1 Relay 3.573,0.74 4.031,0.938 0.458,0.198 10 false IG 1.479,8.417 3.333,8.635 1.854,0.219 10 false : CAN Communication Line 3.365,0.625 3.823,0.823 0.458,0.198 10 false 1 3.333,7.646 3.75,7.854 0.417,0.208 10 false A45 4.854,4.854 5.271,5.063 0.417,0.208 10 false 7 4.854,5.156 5.271,5.365 0.417,0.208 10 false 8 4.844,6.844 5.26,7.052 0.417,0.208 10 false 6 5.594,5.583 6.01,5.792 0.417,0.208 10 false A9 6.031,4.854 6.448,5.063 0.417,0.208 10 false 2 6.031,5.135 6.448,5.344 0.417,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle proximity notification system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the automatic high beam system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE PROXIMITY NOTIFICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.

Body Electrical > Vehicle Proximity Notification System > Trouble Codes
50001 393

e.

Check for DTCs.


Result:
Result Proceed to
DTC B1350 is not output A
DTC B1350 is output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Proximity Sound (Vehicle Stationary) 0 km/h (0 mph) vehicle proximity warning sound OFF or ON -
Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display
Proximity Sound (Vehicle Stationary)
50004 393 2

Result:
Result Proceed to
The warning sound is produced A
The warning sound is not produced B



A

B

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
a.

Disconnect the A45 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR