|
*1: Connect the GTS to the DLC3 when measuring the fluid pressure. *2: Depress the accelerator pedal at a consistent angle to maintain the specified vehicle speed. |
||
| Engine stall speed | D | 2350 +/- 300 rpm |
| Fluid pressure (Throttle valve fully opened)*1 | ||
| Engine stall speed
2350 +/- 300 rpm |
D | 3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi) |
| R | 1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi) | |
| Time lag | N → D | Less than 1.2 seconds |
| N → R | Less than 1.5 seconds | |
| Engine idle speed (A/C off) | N | 750 to 850 rpm |
| Shift schedule (D) (NORMAL) | ||
| Throttle valve position (100%) | Fully depressed
(Before 1st up-shift) |
6100 to 6900 rpm |
| Fully depressed
(Before 2nd up-shift) |
6100 to 6900 rpm | |
| Throttle valve position (Constant opening angle)*2 | 30 km/h (19 mph) | 750 to 1200 rpm |
| 70 km/h (43 mph) | 1000 to 1500 rpm | |
| 100 km/h (62 mph) | 1300 to 1800 rpm | |
| Kick down | Accelerator pedal fully depressed above 30 km/h (19 mph) | 2500 rpm or more |
| Shift schedule (D) (SPORT) | ||
| Throttle valve position (100%) | Fully depressed
(Before 1st up-shift) |
6100 to 6900 rpm |
| Fully depressed
(Before 2nd up-shift) |
6100 to 6900 rpm | |
| Throttle valve position (Constant opening angle)*2 | 30 km/h (19 mph) | 1500 to 1950 rpm |
| 70 km/h (43 mph) | 2000 to 2500 rpm | |
| 100 km/h (62 mph) | 2400 to 2900 rpm | |
| Kick down | Accelerator pedal fully depressed above 30 km/h (19 mph) | 2500 rpm or more |
| Lock-up point | ||
| Lock-up ON
(Accelerator pedal opening 5%) |
D (NORMAL) | 10 to 30 km/h (6 to 19 mph) |
| D (SPORT) | ||
| Lock-up OFF
(Accelerator pedal opening 0%) |
D (NORMAL) | 5 to 20 km/h (3 to 12 mph) |
| D (SPORT) | ||
|
*: Using CVT (Continuously Variable Transaxle) fluid other than the above type may cause abnormal noise or vibration, or damage the CVT (Continuously Variable Transaxle) of your vehicle. |
|||
| Dry fill | w/o Stop and Start System | 8.6 liters (9.1 US qts, 7.6 Imp. qts) | Toyota Genuine CVT fluid FE* |
| w/ Stop and Start System | 8.3 liters (8.8 US qts, 7.3 Imp. qts) | ||
| Transaxle housing type T oil seal | Standard Depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Input shaft sub-assembly | Standard input shaft end play | 0.345 to 1.357 mm (0.0136 to 0.0534 in.) | |
| Clearance of C-1 clutch | Pack clearance (Reference) | 0.45 to 0.75 mm (0.0177 to 0.0295 in.) | |
| Forward clutch flange thickness | Part number | Thickness (mm (in.)) | Mark |
| 35635-12280 | 3.3 (0.130) | B | |
| 35635-12290 | 3.4 (0.134) | C | |
| 35635-12300 | 3.5 (0.138) | D | |
| 35635-12310 | 3.6 (0.142) | E | |
| 35635-12320 | 3.7 (0.146) | F | |
| 35635-12330 | 3.8 (0.150) | G | |
| Forward clutch return spring sub-assembly | Standard free length | 18.54 mm (0.730 in.) | |
| Planetary gear assembly | Standard clearance | 0.16 to 0.61 mm (0.00630 to 0.0240 in.) | |
| Clearance of No. 1 brake | Pack clearance | 0.539 to 1.321 mm (0.0212 to 0.0520 in.) | |
| 1st and reverse brake return spring sub-assembly | Standard free length | 17.56 mm (0.691 in.) | |
| Thrust needle roller bearing and thrust bearing race diameter | Mark | Thrust bearing race diameter inside / outside
mm (in.) |
Thrust needle roller bearing diameter inside / outside
mm (in.) |
| A | - | 47.75 (1.88) / 65.8 (2.59) | |
| B | 26.38 (1.04) / 38.9 (1.53) | 24.9 (0.98) / 38.9 (1.53) | |
| C | - | 29.7 (1.17) / 49.1 (1.93) | |
| Straight pin | Protrusion height | 7.0 to 8.0 mm (0.276 to 0.315 in.) | |
| Differential case tapered roller bearing preload (at 10 rpm) | Standard turning torque | 1.65 to 2.66 N*m (17 to 27 kgf*cm, 15 to 23 in.*lbf) | |
| Shim thickness | Part number | Thickness (mm (in.)) | Mark |
| 90564-66038 | 1.76 (0.0693) | A | |
| 90564-66039 | 1.79 (0.0705) | B | |
| 90564-66067 | 1.82 (0.0717) | C | |
| 90564-66068 | 1.85 (0.0728) | D | |
| 90564-66069 | 1.88 (0.0740) | E | |
| 90564-66070 | 1.91 (0.0752) | F | |
| 90564-66071 | 1.94 (0.0764) | G | |
| 90564-66072 | 1.97 (0.0776) | H | |
| 90564-66073 | 2.00 (0.0787) | J | |
| 90564-66074 | 2.03 (0.0799) | K | |
| 90564-66075 | 2.06 (0.0811) | L | |
| 90564-66076 | 2.09 (0.0823) | M | |
| 90564-66077 | 2.12 (0.0835) | N | |
| 90564-66078 | 2.15 (0.0846) | P | |
| 90564-66079 | 2.18 (0.0858) | Q | |
| 90564-66080 | 2.21 (0.0870) | R | |
| 90564-66081 | 2.24 (0.0882) | S | |
| 90564-66082 | 2.27 (0.0894) | T | |
| 90564-66083 | 2.30 (0.0906) | U | |
| 90564-66084 | 2.33 (0.0917) | V | |
| Adjust reduction driven gear tapered roller bearing preload (at 10 rpm) | Standard turning torque | Differential case tapered roller bearing preload + 3.21 to 6.11 N*m (33 to 62 kgf*cm, 2 to 5 ft.*lbf) | |
| Shim thickness | Part number | Thickness (mm (in.)) | Mark |
| 90564-44070 | 1.59 (0.0626) | A | |
| 90564-44071 | 1.62 (0.0638) | B | |
| 90564-44072 | 1.65 (0.0650) | C | |
| 90564-44073 | 1.68 (0.0661) | D | |
| 90564-44074 | 1.71 (0.0673) | E | |
| 90564-44075 | 1.74 (0.0685) | F | |
| 90564-44076 | 1.77 (0.0697) | G | |
| 90564-44077 | 1.80 (0.0709) | H | |
| 90564-44078 | 1.83 (0.0720) | J | |
| 90564-44079 | 1.86 (0.0732) | K | |
| 90564-44080 | 1.89 (0.0744) | L | |
| 90564-44081 | 1.92 (0.0756) | M | |
| 90564-44082 | 1.95 (0.0768) | N | |
| 90564-44083 | 1.98 (0.0780) | P | |
| 90564-44084 | 2.01 (0.0791) | Q | |
| 90564-44085 | 2.04 (0.0803) | R | |
| 90564-44086 | 2.07 (0.0815) | S | |
| 90564-44087 | 2.10 (0.0827) | T | |
| 90564-44088 | 2.13 (0.0839) | U | |
| 90564-44089 | 2.16 (0.0850) | V | |
| 90564-44090 | 2.19 (0.0862) | W | |
| 90564-44091 | 2.22 (0.0874) | X | |
| 90564-44092 | 2.25 (0.0886) | Y | |
| Front drive shaft oil seal LH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Transaxle housing type T oil seal | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Drive plate runout | Maximum | 0.30 mm (0.0118 in.) |
| Front drive shaft oil seal LH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Front drive shaft oil seal RH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Tester Connection | Condition | Specified Condition |
| 1 (NTO) - 2 (NTB) | Low signal | 4 to 8 mA |
| High signal | 12 to 16 mA |
| Tester Connection | Condition | Specified Condition |
| 1 (NOO) - 2 (NOB) | Low signal | 4 to 8 mA |
| High signal | 12 to 16 mA |
| Tester Connection | Condition | Specified Condition |
| 1 (NSSO) - 2 (NSSB) | Low signal | 4 to 8 mA |
| High signal | 12 to 16 mA |
| Standard voltage (Combined dry-cell battery voltage of 4.5 V) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (VOUT) - 3 (GND) | High signal | 4.09 to 4.19 V |
| Low signal | 0.36 to 0.45 V | |
| Reference voltage (Combined dry-cell battery voltage of 5.0 V) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (VOUT) - 3 (GND) | High signal | 4.55 to 4.65 V |
| Low signal | 0.4 to 0.5 V | |
| Tester Connection | Condition | Specified Condition |
| 4 (B) - 5 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P and N | 10 kΩ or higher | |
| 2 (RB) - 6 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 2 (RB) - 9 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 2 (RB) - 7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| Shift lever not in D, M, "+" or "-" | 10 kΩ or higher |
| Shift lock control ECU (w/ Smart Entry and Start System) | ||
| Wire harness | ||
| Tester Connection | Condition | Specified Condition |
| 4 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 5 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 1 (E) - Body ground | Always | Below 1 Ω |
| Shift lock solenoid | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Shift lock control ECU (w/o Smart Entry and Start System) | ||
| Wire harness | ||
| Tester Connection | Condition | Specified Condition |
| 8 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 1 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 7 (E) - Body ground | Always | Below 1 Ω |
| 5 (KLS+) - Body ground | Ignition switch ACC and shift lever in P | Below 1 V |
| Ignition switch ACC and shift lever not in P | 11 to 14 V | |
| Shift lock solenoid | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Transmission control switch (for LHD) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| 3 (SFTU) - 2 (E) | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| Shift lever not held in "+"
(Up-shift) |
10 kΩ or higher | |
| 1 (SFTD) - 2 (E) | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| Shift lever not held in "-"
(Down-shift) |
10 kΩ or higher | |
| Transmission control switch (for RHD) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| 1 (SFTU) - 2 (E) | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| Shift lever not held in "+"
(Up-shift) |
10 kΩ or higher | |
| 3 (SFTD) - 2 (E) | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| Shift lever not held in "-"
(Down-shift) |
10 kΩ or higher | |
| NORMAL mode switch: | ||
| Tester Connection | Condition | Specified Condition |
| 8 (B) - 13 (GND) | NORMAL mode switch being pushed and held | Below 1 Ω |
| NORMAL mode switch not pushed | 10 kΩ or higher | |
| SPORT mode switch: | ||
| Tester Connection | Condition | Specified Condition |
| 9 (P) - 13 (GND) | SPORT mode switch being pushed and held | Below 1 Ω |
| SPORT mode switch not pushed | 10 kΩ or higher | |
| ECO mode switch: | ||
| Tester Connection | Condition | Specified Condition |
| 7 (ECU) - 13 (GND) | ECO mode switch being pushed and held | Below 1 Ω |
| ECO mode switch not pushed | 10 kΩ or higher | |
| Illumination Illuminates: | ||
| Battery positive (+) → Terminal 12 (ILL+)
Battery negative (-) → Terminal 1 (ILL-) |
Illuminates | |
| No. 1 transmission shift switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 1 (SDN) - 2 (ECC) | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher | |
| 1 (SDN) - 3 (ECC') | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher | |
| No. 2 transmission shift switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 1 (SUP) - 2 (ECC') | "+" (Up shift) shift paddle switch operated and held | Below 2.5 Ω |
| "+" (Up shift) shift paddle switch not operated | 1 MΩ or higher | |
| Shift solenoid valve (SLG, SL1, SL2, SLU, SLP, SLS) | ||
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |