When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.
When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2341 | Sensor (Motor) Failure | Sensor (motor) failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the motor) | ·
Sliding roof ECU (Sliding roof drive gear sub-assembly) ·
Map light sub-assembly (slide/tilt switch) ·
Harness or connector |
| B2344 | Position Failure | Position failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the gear position) | ·
Sliding roof ECU (Sliding roof drive gear sub-assembly) ·
Map light sub-assembly (slide/tilt switch) ·
Harness or connector |
If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
Check the sliding roof auto operation.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK
Auto operation operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
DTCs B2341 or B2344 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Moon Roof)>DISASSEMBLY
Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
DTCs B2341 or B2344 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Moon Roof)>DISASSEMBLY
Perform the Active Test according to the display on the GTS.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof motor | OFF / Opn/Dwn / Clos/Up | - |
| Tester Display |
|---|
| Slide Roof |
Slide roof is operated using GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Moon Roof)>DISASSEMBLY
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | OPEN switch signal | OFF or ON | OFF: OPEN switch on the slide switch not pressed
ON: OPEN switch on the slide switch pressed |
- |
| Close Switch | CLOSE switch signal | OFF or ON | OFF: CLOSE switch on the slide switch not pressed
ON: CLOSE switch on the slide switch pressed |
- |
| Up Switch | UP switch signal | OFF or ON | OFF: UP switch not on the tilt switch pressed
ON: UP switch on the tilt switch pressed |
- |
| Down Switch | DOWN switch signal | OFF or ON | OFF: DOWN switch on the tilt switch not pressed
ON: DOWN switch on the tilt switch pressed |
- |
| Tester Display |
|---|
| Open Switch |
| Close Switch |
| Up Switch |
| Down Switch |
The GTS display changes according to the operation of each switch as shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Moon Roof)>DISASSEMBLY
NG
Remove the map light sub-assembly (slide/tilt switch).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL
Inspect the map light sub-assembly (slide/tilt switch).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the P20 map light sub-assembly (slide/tilt switch) connector.
Disconnect the P4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P4-5 (UP) - P20-19 (UP) | Always | Below 1 Ω |
| P4-8 (CLS) - P20-16 (CLS) | Always | Below 1 Ω |
| P4-9 (DWN) - P20-18 (DOWN) | Always | Below 1 Ω |
| P4-10 (OPN) - P20-17 (OPN) | Always | Below 1 Ω |
| P4-2 (E) - Body ground | Always | Below 1 Ω |
| P20-13 (GND) - Body ground | Always | Below 1 Ω |
| P4-5 (UP) or P20-19 (UP) - Body ground | Always | 10 kΩ or higher |
| P4-8 (CLS) or P20-16 (CLS) - Body ground | Always | 10 kΩ or higher |
| P4-9 (DWN) or P20-18 (DOWN) - Body ground | Always | 10 kΩ or higher |
| P4-10 (OPN) or P20-17 (OPN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Moon Roof)>DISASSEMBLY
NG