Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425053 MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY)  P322F11  Communication Error from Airbag to Generator Circuit Short to Ground  


DESCRIPTION

The motor generator ECU located in the inverter with converter assembly detects a problem in the collision signal line from the airbag sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P322F11 Communication Error from Airbag to Generator Circuit Short to Ground Short to ground in the communication circuit:
Communication from the airbag sensor assembly stopped and circuit Low has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Inverter with converter assembly


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P322F11 Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A411939E04
1.896,0.958 2.427,1.167 0.531,0.208 10 false GSW2 2.427,0.958 2.656,1.167 0.229,0.208 10 false 24 2.427,1.271 2.656,1.479 0.229,0.208 10 false 33 2.125,1.281 2.354,1.49 0.229,0.208 10 false E1 1.083,2.26 2.844,2.552 1.76,0.292 10 false Airbag Sensor Assembly 1.083,2.094 1.563,2.292 0.479,0.198 10 false G70 4.646,0.938 4.875,1.146 0.229,0.208 10 false 18 4.906,0.958 5.396,1.156 0.49,0.198 10 false ABFS 5.604,0.448 5.896,0.667 0.292,0.219 10 false +B 4.719,2.094 5.208,2.292 0.49,0.198 10 false A87 4.719,2.281 6.875,2.552 2.156,0.271 10 false Inverter with Converter Assembly

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
C374925C18
0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Component with harness connected
(Airbag Sensor Assembly)


Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG




OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the G70 airbag sensor assembly connector.


b.

Turn the power switch on (IG).


c.
C384271C07
0.479,0.938 0.792,1.167 0.313,0.229 2.521,1.802 1.854,1.271 true 0.104,0.083 0.344,0.26 0.24,0.177 10 false *a 2.552,1.823 3.063,2 0.51,0.177 10 false GSW2 0.521,0.979 0.833,1.156 0.313,0.177 10 false G70
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G70-24 (GSW2) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the G70 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE AIR BAG SENSOR ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
5.REPLACE AIR BAG SENSOR ASSEMBLY

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395

f.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT (MOTOR GENERATOR)
7.CHECK DTC OUTPUT (MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and wait for 2 minutes or more.


c.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P322F11 is not output. A
P322F11 is output. B



e.

Turn the power switch off.



A

COMPLETED

B

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A87 inverter with converter assembly connector.


c.

Disconnect the G70 airbag sensor assembly connector.


d.
C414518C01
0.396,1.063 0.771,1.281 0.375,0.219 0.49,3.104 0.896,3.344 0.406,0.24 2.656,0.5 2.031,1.188 true 1.875,3.521 2.406,4.177 true 0.458,1.094 0.76,1.313 0.302,0.219 10 false A87 2.708,0.323 3.208,0.552 0.5,0.229 10 false ABFS 0.146,0.135 0.646,0.365 0.5,0.229 10 false *a 0.552,3.146 1.052,3.375 0.5,0.229 10 false G70 2.417,4.229 2.917,4.458 0.5,0.229 10 false GSW2 0.208,2.26 0.708,2.49 0.5,0.229 10 false *b
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Open):
Tester Connection Condition Specified Condition
A87-18 (ABFS) - G70-24 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Short):
Tester Connection Condition Specified Condition
A87-18 (ABFS) or G70-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Reconnect the G70 airbag sensor assembly connector.


f.

Reconnect the A87 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR