Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425054 REAR MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY) D

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY)  DIAGNOSIS SYSTEM  


DESCRIPTION


The motor generator control ECU (MG ECU) (inverter with converter assembly) has a self-diagnosis system. If the motor generator control ECU (MG ECU), motor generator control system, rear motor generator control system or a component is not working properly, the ECU records the conditions that relate to the fault. The ECU also illuminates the master warning in the combination meter assembly and provides other appropriate messages on the multi-information display, such as the HV system warning message, HV battery warning message or discharge warning message.

·

When troubleshooting OBD II (On-Board Diagnostics) vehicles, the GTS (complying with SAE J1978) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle motor generator control ECU can then be read.

·
F102311

OBD II regulations require that the vehicle's on-board computer illuminates the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:

(a)

The emission control system components.

(b)

The powertrain control components (which affect vehicle emissions).

(c)

The computer itself.

In addition, the applicable DTCs prescribed by SAE J2012 are recorded in the motor generator control ECU memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the motor generator control ECU memory.


·

To check for DTCs, connect the GTS to the DLC3. The GTS displays DTCs, freeze frame data, and a variety of hybrid control system data. The DTCs and freeze frame data can be cleared with the GTS. In order to enhance the OBD function on vehicles and develop the off-board diagnosis system, Controller Area Network (CAN) communication is used in this system. CAN is a network which uses a pair of data transmission lines spanning multiple computers and sensors. It allows for high speed communications between the systems and simplification of the wire harness connections.



2 TRIP DETECTION LOGIC


Following is the description for storage of DTC using "2 trip detection logic".

When a malfunction is first detected, the malfunction is temporarily stored in the motor generator control ECU memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


The motor generator control ECU records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



AUXILIARY BATTERY VOLTAGE


Standard Voltage:
Switch Condition Specified Condition
Power switch on (IG) 11 to 14 V


If voltage is below 11 V, recharge or replace the auxiliary battery.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




MIL (Malfunction Indicator Lamp)


a.

The MIL is illuminated when the power switch is first turned on (IG), before the READY indicator illuminates.


b.

When the READY indicator illuminates, the MIL should turn off. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in a system.

HINT:

If the MIL is not illuminated when the power switch is first turned on (IG), check the MIL circuit.

for SFI System: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>MIL Circuit




RELEVANT SYSTEMS CHECK


The inspection areas and outline of the inspection for each circuit are listed below.

C410407E01
0.094,0.073 2.76,0.302 2.667,0.229 10 false Inspection Areas of Relevant Systems 0.646,0.729 2.646,1.24 2,0.51 10 false Inverter Water Pump With Motor Assembly (Coolant Path) 1.302,1.781 2.354,2.021 1.052,0.24 10 false Cooling System 1.052,2.458 2.729,2.656 1.677,0.198 10 false Shut Down Signal Circuit 0.729,2.958 2.479,3.365 1.75,0.406 10 false Hybrid Vehicle Control ECU Assembly 1.448,3.542 2.698,3.802 1.25,0.26 10 false Shutdown Signal 1.094,4.385 2.656,4.688 1.563,0.302 10 false Communication Circuit 0.625,5.031 2.052,5.271 1.427,0.24 10 false Power Source Circuit 1.219,5.302 2.469,5.865 1.25,0.563 10 false Inverter Low-voltage Circuit 1.125,7.063 2.667,7.594 1.542,0.531 10 false HV Battery High-voltage Line Circuit 0.76,6.667 2.292,6.865 1.531,0.198 10 false HV Battery 1.385,8.083 2.271,8.271 0.885,0.188 10 false : Coolant 1.385,8.458 2.875,8.719 1.49,0.26 10 false : High Voltage Line 4.125,8.229 5.635,8.458 1.51,0.229 10 false : Inspection Areas 2.573,7.49 5.104,7.781 2.531,0.292 10 false Inverter with Converter Assembly 4.677,0.802 6.208,1 1.531,0.198 10 false Motor Resolver 4.625,1.167 6.281,1.375 1.656,0.208 10 false Motor Resolver Circuit 4.667,1.833 6.198,2.031 1.531,0.198 10 false Generator Resolver 4.542,2.177 6.375,2.438 1.833,0.26 10 false Generator Resolver Circuit 4.698,4.292 6.229,4.49 1.531,0.198 10 false Motor (MG2) 4.573,4.656 6.188,5.094 1.615,0.438 10 false Motor High-voltage Circuit 4.677,5.354 6.208,5.552 1.531,0.198 10 false Generator (MG1) 4.635,5.719 6.135,6.115 1.5,0.396 10 false Generator High-voltage Circuit 4.542,3.24 6.542,3.448 2,0.208 10 false Rear Motor Resolver Circuit 4.698,6.615 6.229,6.813 1.531,0.198 10 false Rear Motor (MGR) 4.646,7.01 6.135,7.375 1.49,0.365 10 false Rear Motor High-voltage Circuit 4.667,2.885 6.198,3.083 1.531,0.198 10 false Rear Motor Resolver

Inspection Details of Relevant Systems
System to be Inspected Malfunction Possibility Inspection Content
Motor Resolver Circuit Motor resolver signal

Open or short circuit in the motor resolver, connectors or cables


Motor High-voltage Circuit Motor (MG2) output

Open or short circuit in the motor (MG2), connectors or cables


Generator Resolver Circuit Generator resolver signal

Open or short circuit in the generator resolver, connectors or cables


Generator High-voltage Circuit Generator (MG1) output

Open or short circuit in the generator (MG1), connectors or cables


Rear Motor Resolver Circuit Rear motor resolver signal

Open or short circuit in the rear motor resolver, connectors or cables


Rear Motor High-voltage Circuit Rear motor (MGR) output

Open or short circuit in the rear motor (MGR), connectors or cables


Inverter Low-voltage Circuit Power supply voltage from +B or communication between hybrid vehicle control ECU and motor generator control ECU
·

Open or short circuit in communication line between hybrid vehicle control ECU and motor generator control ECU

·

Open or short circuit in the +B or ground lines

·

Fuse is blown


HV Battery High-voltage Line Circuit High voltage power supply from HV battery

Open or short circuit in the system main relay, connectors or cables


Cooling System Temperature abnormally high
·

Grille blockage

·

Whether coolant is present

·

Whether there is a possibility that coolant was frozen when malfunction occurs

·

Cooling hose blockage

·

HV radiator fan operation


Shutdown Signal Circuit Shutdown signal

Open or short circuit in shutdown signal communication line between hybrid vehicle control ECU and motor generator ECU




DTC PRIORITY LEVEL AND TROUBLE AREAS


·

Each DTC diagnostic procedure for the hybrid control system consists of a combination of the various relevant system (circuit) inspections.

·

When multiple DTCs are output, performing each diagnostic procedure in order of priority can lead to a more accurate diagnosis.


C410408E02
0.083,0.125 2.979,0.385 2.896,0.26 10 false DTC Diagnostic Procedure Pattern 0.073,0.698 2.396,0.938 2.323,0.24 10 false Preliminary Check and Confirmation 0.885,1.01 2.448,1.208 1.563,0.198 10 false Motor Resolver Circuit 0.656,1.302 2.375,1.542 1.719,0.24 10 false Motor High-voltage Circuit 0.615,1.583 2.448,1.781 1.833,0.198 10 false Generator Resolver Circuit 0.396,1.865 2.5,2.115 2.104,0.25 10 false Generator High-voltage Circuit 0.583,2.729 2.448,2.958 1.865,0.229 10 false Inverter Low-voltage Circuit 0.042,3.01 2.698,3.26 2.656,0.25 10 false HV Battery High-voltage Line Circuit 1.25,3.292 2.292,3.521 1.042,0.229 10 false Cooling System 0.698,3.573 2.563,3.823 1.865,0.25 10 false Shut Down Signal Circuit 0.083,4.417 4.75,4.635 4.667,0.219 10 false *1: For A through Q, refer to "DTC Order of Priority and Trouble Area" below. 6.719,0.49 7.031,0.688 0.313,0.198 10 false *1 0.542,2.167 2.427,2.396 1.885,0.229 10 false Rear Motor Resolver Circuit 0.323,2.448 2.354,2.677 2.031,0.229 10 false Rear Motor High-voltage Circuit

Inspection Details of Relevant Systems
DTC No. Detection Item Order of Priority Inspection Pattern
1 2 3 4 5
Microcomputer Malfunction Power Source Circuit Malfunction Communication System Malfunction Sensor and Actuator Circuit Malfunction System Malfunction
P0A4516 Drive Motor "B" Position Sensor Circuit Voltage Below Threshold - - - ○ - G
P0A451F Drive Motor "B" Position Sensor Circuit Intermittent - - - ○ - G
P0A4521 Drive Motor "B" Position Sensor Signal Amplitude < Minimum - - - ○ - G
P0A4522 Drive Motor "B" Position Sensor Signal Amplitude > Maximum - - - ○ - G
P0A6912 Drive Motor "B" Phase V Current (High Resolution) Circuit Short to Battery - - - ○ - A
P0A6914 Drive Motor "B" Phase V Current (High Resolution) Circuit Short to Ground or Open - - - ○ - A
P0A691C Drive Motor "B" Phase V Current (High Resolution) Circuit Voltage Out of Range - - - ○ - A
P0A691F Drive Motor "B" Phase V Current (High Resolution) Circuit Intermittent - - - ○ - A
P0A6C12 Drive Motor "B" Phase W Current (High Resolution) Circuit Short to Battery - - - ○ - A
P0A6C14 Drive Motor "B" Phase W Current (High Resolution) Circuit Short to Ground or Open - - - ○ - A
P0A6C1C Drive Motor "B" Phase W Current(High Resolution) Circuit Voltage Out of Range - - - ○ - A
P0A6C1F Drive Motor "B" Phase W Current(High Resolution) Circuit Intermittent - - - ○ - A
P0A7972 Drive Motor "B" Inverter Actuator Stuck Open - - - - ○ O
P0A7973 Drive Motor "B" Inverter Actuator Stuck Closed - - - - ○ -
P0A799E Drive Motor "B" Inverter Stuck On - - - - ○ D
P0A9100 Drive Motor "B" Performance - - - - ○ K
P0AF211 Drive Motor Inverter Temperature Sensor "B" Circuit Short to Ground - - - ○ - -
P0AF215 Drive Motor Inverter Temperature Sensor "B" Circuit Short to Battery or Open - - - ○ - -
P0AF21C Drive Motor Inverter Temperature Sensor "B" Circuit Voltage Out of Range - - - ○ - B
P0BF112 Drive Motor "B" Phase U Current Sensor Circuit Short to Battery - - - ○ - A
P0BF114 Drive Motor "B" Phase U Current Sensor Circuit Short to Ground or Open - - - ○ - A
P0BF11F Drive Motor "B" Phase U Current Sensor Circuit Intermittent - - - ○ - A
P0BF128 Drive Motor "B" Phase U Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P0BF512 Drive Motor "B" Phase V Current Sensor Circuit Short to Battery - - - ○ - A
P0BF514 Drive Motor "B" Phase V Current Sensor Circuit Short to Ground or Open - - - ○ - A
P0BF51F Drive Motor "B" Phase V Current Sensor Circuit Intermittent - - - ○ - A
P0BF528 Drive Motor "B" Phase V Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P0BF912 Drive Motor "B" Phase W Current Sensor Circuit Short to Battery - - - ○ - A
P0BF914 Drive Motor "B" Phase W Current Sensor Circuit Short to Ground or Open - - - ○ - A
P0BF91F Drive Motor "B" Phase W Current Sensor Circuit Intermittent - - - ○ - A
P0BF928 Drive Motor "B" Phase W Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure - - - ○ - A
P0BFE62 Drive Motor "B" Phase U-V-W Current Sensor Signal Compare Failure - - - ○ - O
P0C021D Drive Motor "B" System Circuit Current Out of Range - - - - ○ Q
P0C1A00 Drive Motor "B" Execution Torque Performance - - - - ○ Q
P0C5513 Drive Motor "B" Position Sensor Circuit "A" Circuit Open - - - ○ - G
P0C5516 Drive Motor "B" Position Sensor Circuit "A" Circuit Voltage Below Threshold - - - ○ - A
P0C5517 Drive Motor "B" Position Sensor Circuit "A" Circuit Voltage Above Threshold - - - ○ - A
P0C551F Drive Motor "B" Position Sensor Circuit "A" Circuit Intermittent - - - ○ - G
P0C5F13 Drive Motor "B" Position Sensor Circuit "B" Circuit Open - - - ○ - G
P0C5F16 Drive Motor "B" Position Sensor Circuit "B" Circuit Voltage Below Threshold - - - ○ - A
P0C5F17 Drive Motor "B" Position Sensor Circuit "B" Circuit Voltage Above Threshold - - - ○ - A
P0C5F1F Drive Motor "B" Position Sensor Circuit "B" Circuit Intermittent - - - ○ - G
P1BF946 Internal Control Module (EEPROM Estimated Temperature Information) Calibration / Parameter Memory Failure ○ - - - - -
P1BFA46 Internal Control Module (EEPROM Resolver Learning Value) Calibration / Parameter Memory Failure ○ - - - - -
P1C2C1C Drive Motor "B" Control Module AD Converter Circuit Voltage Out of Range ○ - - - - -
P1C2C49 Drive Motor "B" Control Module AD Converter Circuit Internal Electronic Failure ○ - - - - -
P1C5E19 Drive Motor "B" Inverter Circuit Current Above Threshold - - - - ○ D
P1C631F Drive Motor "B" Control Module Offset Power Circuit Intermittent - ○ - - - -
P1C661F Drive Motor "B" Control Module Circuit Intermittent ○ - - - - C
P1C681F Drive Motor "B" Phase U-V-W Current Sensor Circuit Intermittent - - - ○ - O
P1CAE49 Drive Motor "B" Position Sensor Internal Electronic Failure - - - ○ - C
P1CB138 Drive Motor "B" Position Sensor REF Signal Frequency Incorrect - - - ○ - C
P262C1C Drive Motor "B" Control Module Offset Power Circuit Voltage Out of Range - ○ - - - -
P310B1F Communication Error from Drive Motor "A" to Drive Motor "B" Circuit Intermittent ○ - - - - -
P310B83 Communication Error from Drive Motor "A" to Drive Motor "B" Value of Signal Protection Calculation Incorrect ○ - - - - -
P310B86 Communication Error from Drive Motor "A" to Drive Motor "B" Signal (Some Circuit Quantity, Reported via Serial Data) Invalid ○ - - - - -
P310B87 Communication Error from Drive Motor "A" to Drive Motor "B" Missing Message ○ - - - - -
P32CF1F Lost Communication between Drive Motor "A" and "B" (Drive Motor "B") Circuit Intermittent ○ - - - - -
P32CF83 Lost Communication between Drive Motor "A" and "B" (Drive Motor "B") Value of Signal Protection Calculation Incorrect ○ - - - - -
P32CF86 Lost Communication between Drive Motor "A" and "B" (Drive Motor "B") Signal (Some Circuit Quantity, Reported via Serial Data) Invalid ○ - - - - -
P32CF87 Lost Communication between Drive Motor "A" and "B" (Drive Motor "B") Missing Message ○ - - - - -

HINT:

The "Example of Multiple DTCs being Output" below is only one example of a malfunction condition. Therefore, a determination should not be made based on this alone.

Example of Multiple DTCs being Output:
1.

The power supply of the microcomputer decreases while the vehicle is being driven.

(a)

DTCs are detected and the vehicle behavior is as follows.


Detected DTCs
-

P262C1C (Drive Motor "B" Control Module Offset Power Circuit Voltage Out of Range): Power source malfunction*

-

P0A4516 (Drive Motor B" Position Sensor Circuit Voltage Below Threshold): Sensor and actuator circuit malfunction*

-

P0C5516 (Drive Motor B" Position Sensor Circuit "A" Circuit Voltage Below Threshold): Sensor and actuator circuit malfunction*

-

P1CAE49 (Drive Motor B" Position Sensor Internal Electronic Failure): Sensor and actuator circuit malfunction*

*: Check the priority level in the "DTC Order of Priority" chart above.



Vehicle Behavior

AWD stopped

System stopped


2.

The inspection order of priority is: Microcomputer circuit → power source circuit → communication circuit → sensor and actuator circuit → system circuit. Therefore, check the repair procedure for P262C1C.

3.

Follow the repair procedures and replace the inverter with converter assembly. Finish the repair.


It is possible to check only the specified malfunctioning parts without having to check irrelevant parts.