AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK
Make sure that the customize settings are set to default when performing the automatic light control system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Turn the ignition switch to ON.
Turn the light control switch to the AUTO position.
Cover the automatic light control sensor.
Check that the taillights and low beam headlights come on.
Uncover the automatic light control sensor.
Check that the low beam headlights and taillights turn off.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (except Driver Door-linked Auto Light Turn-off System)
When the light control switch is in the TAIL or HEAD position
Turn the ignition switch to ON.
Turn the low beam headlights or high beam headlights on.
Turn the ignition switch off.
Check that the low beam headlights and high beam headlights turn off immediately.
The taillights and rear fog lights* remain on.
*: w/ Rear Fog Light
When the light control switch is in the AUTO position
Turn the ignition switch to ON.
Turn the taillights, low beam headlights, high beam headlights, front fog lights*1 or rear fog lights*2 on.
*1: w/ Front Fog Light
*2: w/ Rear Fog Light
Turn the ignition switch off.
Check that all of the lights turn off immediately.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (for Driver Door-linked Auto Light Turn-off System)
Close all of the doors.
Turn the ignition switch to ON.
Turn the taillights, low beam headlights, high beam headlights, front fog lights*1 and rear fog lights*2 on.
*1: w/ Front Fog Light
*2: w/ Rear Fog Light
Turn the ignition switch off.
Open the driver door.
Check that all of the lights turn off immediately.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (w/ Delay Function)
Vehicles displaying the Item "Light Auto OFF Delay" on the GTS:
This check is possible only when the "Light Auto OFF Delay" customize setting is set to "ON" on the GTS.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
When the taillights are on (low beam headlights are not on)
Close all of the doors.
Turn the ignition switch to ON.
Turn the taillights on.
Turn the ignition switch off.
Open the driver door.
Check that all of the lights turn off immediately.
When the low beam headlights are on
Close all of the doors.
Turn the ignition switch to ON.
Turn the low beam headlights on.
Turn the ignition switch off.
Open any of the doors.
Close the door.
Check that all of the lights turn off after 30 seconds (delay function).
Before the lights turn off, if the lock button on the key is pushed after all of the doors are locked, all of the lights will turn off immediately.
DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK
*1: for HV Model
*2: for Gasoline Model
*3: w/ Light Control Switch OFF Position
Start the hybrid control system*1 or engine*2.
Turn the light control switch to the OFF*3 or AUTO position (with the low beam headlights not turned on via the automatic light control system).
Release the parking brake.
Check that the daytime running lights come on.
DOOR MIRROR FOOT LIGHT CONTROL OPERATION CHECK (w/ Foot Light)
The operation and condition of this control are described below.
| Operation | Condition |
|---|---|
| Fade in and illuminate constantly | When any of the following conditions is met, the lights fade in and illuminate constantly:
·
A key is detected in the actuation area.*1 ·
Any door is unlocked when the ignition switch is off and all of the doors are closed. |
| Illuminate for 15 seconds, and then fade out | When any of the following conditions is met, the lights illuminate for 15 seconds, and then fade out:
·
An actuation area-linked function is used.*1, *2 ·
Any door is unlocked when the ignition switch is off and all of the doors are closed. |
| Fade out immediately | When the following condition is met, the lights fade out immediately:
·
The ignition switch is turned from off to ON. ·
A key is not detected in the actuation area.*1 ·
All doors are locked when all doors are closed and any door is unlocked. |
*1: w/ Entry Function
*2: When the lights are on, the lights fade out after approximately 3 seconds the key leaves the actuation areas around the doors.
EXTENDED HEADLIGHT LIGHTING OPERATION CHECK (w/ Extended Headlight Lighting)
Turn the ignition switch off.
Turn the light control switch to the AUTO position.
Pull and release the dimmer switch to flash the headlights once.
Check that the low beam headlights come on for approximately 30 seconds.
AUTOMATIC HIGH BEAM SYSTEM OPERATION CHECK (w/ Automatic High Beam System)
| *a | Automatic High Beam Indicator on Combination Meter Assembly |
| *b | Auto High Beam Switch Indicator |
Check the operation of the automatic high beam indicator.
Turn the ignition switch to ON.
Turn the light control switch to the AUTO or HEAD position.
Move the dimmer switch to the High position.
Press the auto high beam switch (indicator illuminates).
If the auto high beam switch is turned on when the light control switch is not in the AUTO or HEAD position, or the dimmer switch is not in the High position, "To Activate Automatic Beam, Switch Headlights to High Beam" will be displayed on the multi-information display.
Check that the automatic high beam indicator illuminates.
When the forward recognition camera cannot correctly detect objects due to inclement weather such as thick fog or other visual obstructions, the automatic high beam indicator may not turn on and consequently the automatic high beam system may not operate.
Check the operation of the automatic high beam function.
At night, when driving the vehicle with the automatic high beam system in standby mode, check that the high beams automatically turn on after a short delay when all of the following conditions are met:
The vehicle speed is more than approximately 40 km/h (25 mph). (for Europe)
The vehicle speed is more than approximately 30 km/h (19 mph). (except Europe)
The area in front of the vehicle is dark.
There are no oncoming vehicles with headlights on.
There are no preceding vehicles with taillights on.
There are few streetlights along the street ahead.
The low beams may not change to high beams due to illumination from city lighting, traffic lights or billboards, or due to reflective surfaces, such as signs or signboards.
At night, when driving the vehicle with the high beams turned on by the automatic high beam system, check that the automatic high beam system turns off the high beams and returns to standby mode when any of the following conditions are met:
The vehicle speed is less than approximately 30 km/h (19 mph). (for Europe)
The vehicle speed is less than approximately 25 km/h (16 mph). (except Europe)
The level of ambient light is higher than a specified threshold.
There are oncoming vehicles with headlights on.
There are preceding vehicles with taillights on.
Light from streetlights ahead is higher than a specified threshold.
Under the following conditions, the high beams may change to the low beams.
There is interference from other illumination, such as city lighting, traffic lights or billboards, or reflective surfaces, such as signs or signboards
There is interference from the fog lights of an oncoming vehicle
Under the following conditions, the high beams may not change to the low beams.
Passing an oncoming vehicle on a curve
Preceding or oncoming vehicle appears and disappears on a continuous curve
Preceding or oncoming vehicle appears and disappears due to the median, roadside trees or other obstacle
Another vehicle cuts in front of the vehicle
When any of the following conditions are met, the automatic high beam system is canceled, and the automatic high beam indicator in the combination meter assembly turns off.
The ignition switch is turned off.
The light control switch is in a position other than AUTO or HEAD.
The low beam headlights are turned off.
The dimmer switch is set to the low beam position.
The auto high beam switch is turned off.
The automatic high beam system may not operate correctly under the following conditions.