The standard voltage, resistance and waveform between each pair of the ECM terminals are shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A24-1 (BATT) - A24-10 (E1) | G - W-B | Battery (for measuring battery voltage and ECM memory) | Always | 11 to 14 V |
| A24-2 (IGSW) - A24-10 (E1) | P - W-B | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| A24-6 (FPC) - A24-10 (E1) | LG - W-B | Fuel pump control | Ignition switch ON | Below 1.5 V |
| Idling with warm engine | Pulse generation
(See waveform 1) |
|||
| A24-7 (CANP)*1 - A24-10 (E1) | B - W-B | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 2) |
| A24-8 (CANH) - A24-10 (E1) | B - W-B | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 2) |
| A24-9 (+B) - A24-10 (E1) | L - W-B | ·
Power source of ECM ·
Power source of throttle actuator |
Ignition switch ON | 11 to 14 V |
| A24-10 (E1) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| A24-15 (MREL) - A24-10 (E1) | W - W-B | EFI-MAIN NO. 1 relay operation signal | Ignition switch ON | Below 1.5 V |
| A24-16 (NEO) - A24-10 (E1) | BR - W-B | Engine speed signal sent to other ECUs | Idling with warm engine | Pulse generation
(See waveform 3) |
| A24-17 (CANN)*1 - A24-10 (E1) | L - W-B | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 4) |
| A24-18 (CANL) - A24-10 (E1) | W - W-B | CAN communication line | Engine stopped, ignition switch ON | Pulse generation
(See waveform 4) |
| A24-21 (STP) - A24-10 (E1) | SB - W-B | Stop light switch assembly signal | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V | |||
| A24-22 (ST1-) - A24-10 (E1) | LG - W-B | Stop light switch assembly signal
(opposite to STP terminal) |
Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| A24-23 (NSW)*1 - A24-10 (E1) | LG - W-B | Park/Neutral position switch assembly signal | Ignition switch ON, shift lever not in P or N | 11 to 14 V |
| Ignition switch ON, shift lever in P or N | Below 3.0 V | |||
| A24-24 (SNWI) - A24-10 (E1) | B - W-B | Drive mode switch (SNOW mode) | Ignition switch ON | 11 to 14 V |
| Ignition switch ON, SNOW mode switch being pushed and held at SNOW position (SNOW mode) | 0 to 1.5 V | |||
| A24-30 (STA) - A24-10 (E1) | G - W-B | Starter assembly signal | Cranking | 6.0 V or higher |
| A24-32 (RFC) - A24-10 (E1) | SB - W-B | Cooling fan control signal | Ignition switch ON, A/C switch on (max cool) | Pulse generation
(See waveform 5) |
| A24-34 (IREL) - A24-10 (E1) | P - W-B | D INJ relay operation signal | Ignition switch ON | Below 1.5 V |
| A24-35 (+B2) - A24-10 (E1) | L - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A24-36 (E2) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| A24-39 (KSW) - A24-10 (E1) | B - W-B | Key in vehicle signal | Key outside vehicle | 11 to 14 V |
| A24-42 (SPD) - A24-10 (E1) | V - W-B | Vehicle speed signal from combination meter assembly | Driving at 20 km/h (12 mph) | Pulse generation
(See waveform 6) |
| A24-45 (EC) - Body ground | BR - - | Ground | Always | Below 1 Ω |
| A24-53 (+BD1) - A24-10 (E1) | W - W-B | Power source of ECU (injector driver) | Ignition switch ON | 11 to 14 V |
| A24-54 (E1D1) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| A24-55 (VPA) - A24-56 (EPA) | G - L | Accelerator pedal position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| A24-57 (VCPA) - A24-56 (EPA) | Y - L | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A24-58 (VPA2) - A24-59 (EPA2) | Y - P | Accelerator pedal position sensor signal | Ignition switch ON, accelerator pedal fully released | 1.2 to 2.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.4 to 4.75 V | |||
| A24-60 (VCP2) - A24-59 (EPA2) | SB - P | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| C40-1 (M-) - A24-10 (E1) | W - W-B | Throttle actuator operation signal (negative signal) | Idling with warm engine | Pulse generation
(See waveform 7) |
| C40-2 (M+) - A24-10 (E1) | B - W-B | Throttle actuator operation signal (positive terminal) | Idling with warm engine | Pulse generation
(See waveform 8) |
| C40-3 (EGA+) - A24-10 (E1) | BE - W-B | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 9) |
| C40-4 (EGA-) - A24-10 (E1) | GR - W-B | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 9) |
| C40-6 (EGB+) - A24-10 (E1) | L - W-B | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 9) |
| C40-5 (EGB-) - A24-10 (E1) | V - W-B | EGR valve assembly operation signal | Idling with warm engine | Pulse generation
(See waveform 9) |
| C40-7 (HTHM) - A24-10 (E1) | G - W-B | Thermostat heater (water inlet with thermostat sub-assembly) operation signal | Ignition switch ON | 11 to 14 V |
| C40-8 (HA1B) - A24-10 (E1) | R - W-B | Air fuel ratio sensor (sensor 2) heater operation signal | Ignition switch ON | 11 to 14 V |
| Idling with cold engine | Pulse generation
(See waveform 10) |
|||
| C40-9 (HA1A) - A24-10 (E1) | R - W-B | Air fuel ratio sensor (sensor 1) heater operation signal | Ignition switch ON | 11 to 14 V |
| Idling with cold engine | Pulse generation
(See waveform 11) |
|||
| C40-11 (#2D+) - A24-10 (E1) | L - W-B | Direct fuel injector assembly signal (No. 2 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-10 (#2D-) - A24-10 (E1) | G - W-B | Direct fuel injector assembly signal (No. 2 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-12 (#3D+) - A24-10 (E1) | W - W-B | Direct fuel injector assembly signal (No. 3 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-13 (#3D-) - A24-10 (E1) | R - W-B | Direct fuel injector assembly signal (No. 3 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-15 (#4D+) - A24-10 (E1) | P - W-B | Direct fuel injector assembly signal (No. 4 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-14 (#4D-) - A24-10 (E1) | V - W-B | Direct fuel injector assembly signal (No. 4 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-16 (#1D+) - A24-10 (E1) | W - W-B | Direct fuel injector assembly signal (No. 1 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-17 (#1D-) - A24-10 (E1) | BR - W-B | Direct fuel injector assembly signal (No. 1 cylinder) | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 12) |
| C40-19 (FP1+) - A24-10 (E1) | W - W-B | Fuel pump assembly (for high pressure side) signal | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 13) |
| C40-18 (FP1-) - A24-10 (E1) | B - W-B | Fuel pump assembly (for high pressure side) signal | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" | Pulse generation
(See waveform 13) |
| C40-21 (VOP+) - A24-10 (E1) | R - W-B | Oil pressure control valve operation signal | Idling with warm engine | Pulse generation
(See waveform 14) |
| C40-20 (VOP-) - A24-10 (E1) | W - W-B | Oil pressure control valve operation signal | Idling with warm engine | Pulse generation
(See waveform 14) |
| C40-26 (OE1+) - C40-25 (OE1-) | P - R | Cam timing oil control solenoid assembly operation signal | Idling | Pulse generation
(See waveform 15) |
| C40-28 (EDT1) - A24-10 (E1) | V - W-B | Cam timing control motor with EDU assembly signal | Idling with warm engine | Pulse generation
(See waveform 16) |
| C40-41 (WSV2)*1 - A24-10 (E1) | LG - W-B | Flow shutting valve (for continuously variable transaxle fluid control) operation signal | Ignition switch ON | 11 to 14 V |
| C40-42 (WSV1) - A24-10 (E1) | B - W-B | Flow shutting valve (for heater control) operation signal | Ignition switch ON | 11 to 14 V |
| C40-44 (ACM)*1 - A24-10 (E1) | G - W-B | Vacuum switching valve (for active control engine mount system) operation signal | Ignition switch ON | 11 to 14 V |
| C40-46 (IGT4) - A24-10 (E1) | B - W-B | No. 4 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 17) |
| C40-47 (IGT3) - A24-10 (E1) | P - W-B | No. 3 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 17) |
| C40-48 (IGT2) - A24-10 (E1) | V - W-B | No. 2 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 17) |
| C40-49 (IGT1) - A24-10 (E1) | W - W-B | No. 1 ignition coil assembly signal
(ignition signal) |
Idling with warm engine | Pulse generation
(See waveform 17) |
| C40-50 (WPO) - A24-10 (E1) | LG - W-B | Electric water pump assembly signal | Idling with warm engine | Pulse generation
(See waveform 18) |
| C40-51 (WPI) - A24-10 (E1) | L - W-B | Electric water pump assembly signal | Idling with warm engine | Pulse generation
(See waveform 19) |
| C40-64 (NIMB)*2 - A24-10 (E1) | V - W-B | Power supply for transmission revolution sensor (NIM) | Ignition switch ON | 11 to 14 V |
| C40-65 (NIMO)*2 - A24-10 (E1) | G - W-B | Transmission revolution sensor (NIM) signal | Engine idling and clutch pedal fully released | Pulse generation
(See waveform 20) |
| C40-66 (PRG) - A24-10 (E1) | W - W-B | Purge VSV operation signal | Ignition switch ON | 11 to 14 V |
| Idling with warm engine, under purge control | Pulse generation
(See waveform 21) |
|||
| C40-69 (VCPX)*3 - C40-68 (EPEX)*3 | L - B | Power source of differential pressure sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-70 (EMR1) - A24-10 (E1) | R - W-B | Cam timing control motor with EDU assembly signal | Idling with warm engine | Pulse generation
(See waveform 22) |
| C40-71 (EMF1) - A24-10 (E1) | L - W-B | Cam timing control motor with EDU assembly signal | Idling with warm engine | Below 5.0 V |
| C40-72 (EMD1) - A24-10 (E1) | G - W-B | Cam timing control motor with EDU assembly signal | Idling with warm engine | Pulse generation
(See waveform 23) |
| C40-73 (#40) - A24-10 (E1) | P - W-B | Port fuel injector assembly signal (No. 4 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 24) |
| C40-74 (#30) - A24-10 (E1) | W - W-B | Port fuel injector assembly signal (No. 3 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 24) |
| C40-75 (#20) - A24-10 (E1) | G - W-B | Port fuel injector assembly signal (No. 2 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 24) |
| C40-76 (#10) - A24-10 (E1) | B - W-B | Port fuel injector assembly signal (No. 1 cylinder) | Idling with warm engine (Data List item "Injection Mode" displaying "Port") | Pulse generation
(See waveform 24) |
| C40-78 (VCVG) - A24-10 (E1) | LG - W-B | Power source of mass air flow meter sub-assembly (specific voltage) | Ignition switch ON | 4.8 to 5.2 V |
| C40-83 (VCNP)*2 - A24-10 (E1) | W - W-B | Power source of neutral position switch | Ignition switch ON | 4.5 to 5.5 V |
| C40-84 (VCPF) - A24-10 (E1) | LG - W-B | Power source of fuel pressure sensor (for low pressure side) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-87 (VTA2) - C40-110 (ETA) | V - B | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 2.1 to 3.1 V |
| Accelerator pedal fully depressed (engine running) | 4.6 to 5.0 V | |||
| C40-88 (VCV1) - A24-10 (E1) | V - W-B | Power source of camshaft position sensor (for intake camshaft) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-90 (VV1+) - C40-89 (VV1-) | B - R | Camshaft position sensor (for intake camshaft) signal | Idling with warm engine | Pulse generation
(See waveform 25) |
| C40-91 (EV1+) - C40-114 (EV1-) | V - G | Camshaft position sensor (for exhaust camshaft) signal | Idling with warm engine | Pulse generation
(See waveform 25) |
| C40-92 (PEX)*3 - C40-68 (EPEX)*3 | GR - B | Differential pressure sensor signal | Ignition switch ON | 0.4 to 4.8 V |
| C40-93 (NE+) - C40-115 (NE-) | L - P | Crankshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 26) |
| C40-94 (A1A-) - A24-10 (E1) | W - W-B | Air fuel ratio sensor (sensor 1) signal | Ignition switch ON | 1.24 to 4.22 V |
| C40-95 (A1A+) - A24-10 (E1) | B - W-B | Air fuel ratio sensor (sensor 1) signal | Ignition switch ON | 1.46 to 4.22 V |
| C40-97 (PR) - C40-96 (EPR) | L - V | Fuel pressure sensor (for high pressure side) signal | Idling with warm engine | 0.5 to 4.5 V |
| C40-98 (VCPR) - C40-96 (EPR) | LG - V | Power source of fuel pressure sensor (for high pressure side) (specific voltage) | Ignition switch ON | 4.75 to 5.25 V |
| C40-99 (VCPE) - C40-100 (EPEO) | R - L | Power source of engine oil pressure and temperature sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-101 (VG) - C40-79 (E2G) | R - W | Mass air flow meter sub-assembly signal | Ignition switch ON | Pulse generation
(See waveform 27) |
| C40-106 (NPSW)*2 - C40-60 (ENPS)*2 | L - B | Neutral position switch signal | Ignition switch ON, Shift lever in neutral | 2.7 to 4.3 V |
| Ignition switch ON, Shift lever not in neutral | 0.7 to 1.9 V | |||
| C40-102 (THA) - C40-79 (E2G) | G - W | Intake air temperature sensor (mass air flow meter sub-assembly) signal | Idling, intake air temperature 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C40-107 (PFL) - C40-61 (EPFL) | V - L | Fuel pressure sensor (for low pressure side) signal | Idling with warm engine | 0.75 to 4.5 V |
| C40-108 (VTA1) - C40-110 (ETA) | P - B | Throttle position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.6 to 1.1 V |
| Accelerator pedal fully depressed (engine running) | 3.2 to 4.8 V | |||
| C40-109 (VCTA) - C40-110 (ETA) | R - B | Power source of throttle position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-111 (KNK1) - C40-112 (EKNK) | R - G | Knock control sensor signal | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(See waveform 28) |
| C40-113 (VCE1) - A24-10 (E1) | L - W-B | Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-116 (VCNE) - A24-10 (E1) | V - W-B | Power source of crankshaft position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C40-117 (A1B-) - A24-10 (E1) | Y - W-B | Air fuel ratio sensor (sensor 2) signal | Ignition switch ON | 1.17 to 4.49 V |
| C40-118 (A1B+) - A24-10 (E1) | BR - W-B | Air fuel ratio sensor (sensor 2) signal | Ignition switch ON | 1.53 to 5.96 V |
| C40-120 (PIM) - C40-119 (EPIM) | P - G | Manifold absolute pressure sensor signal | Ignition switch ON | 3.0 to 4.5 V |
| C40-121 (VCPM) - C40-119 (EPIM) | B - G | Power source of manifold absolute pressure sensor (specific voltage) | Ignition switch ON | 4.75 to 5.25 V |
| C40-122 (PEO) - C40-100 (EPEO) | W - L | Engine oil pressure sensor (engine oil pressure and temperature sensor) signal | Idling with warm engine | 0.5 to 4.5 V |
| C40-123 (THEO) - C40-100 (EPEO) | B - L | Engine oil temperature sensor (engine oil pressure and temperature sensor) signal | Ignition switch ON | 0.14 to 4.93 V |
| C40-125 (THW) - C40-124 (ETHW) | L - P | Engine coolant temperature sensor signal | Idling, engine coolant temperature 75 to 100°C (167 to 212°F) | 0.2 to 1.0 V |
*1: for continuously variable transaxle models
*2: for manual transaxle models
*3: w/ Gasoline particulate filter
WAVEFORM 1
| ECM Terminal Name | Between FPC and E1 |
| Tester Range | 5 V/DIV., 5 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 2
| ECM Terminal Name | Between CANH and E1
Between CANP and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 3
| ECM Terminal Name | Between NEO and E1 |
| Tester Range | 5 V/DIV., 2 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 4
| ECM Terminal Name | Between CANL and E1
Between CANN and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 5
| ECM Terminal Name | Between RFC and E1 |
| Tester Range | 1 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON, A/C switch on (max cool) |
The duty ratio varies depending on the engine coolant temperature.
WAVEFORM 6
| ECM Terminal Name | Between SPD and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 7
| ECM Terminal Name | Between M- and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 8
| ECM Terminal Name | Between M+ and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 9
| ECM Terminal Name | CH1: Between EGA+ and E1
CH2: Between EGA- and E1 |
| CH1: Between EGB+ and E1
CH2: Between EGB- and E1 |
|
| Tester Range | 5 V/DIV., 5 μs./DIV. |
| Condition | Idling with warm engine |
When the EGR valve assembly is operating, a waveform is produced at each terminal.
WAVEFORM 10
| ECM Terminal Name | Between HA1B and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling with cold engine |
WAVEFORM 11
| ECM Terminal Name | Between HA1A and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling with cold engine |
WAVEFORM 12
| ECM Terminal Name | CH1: Between #1D+ and E1
CH2: Between #1D- and E1 |
| CH1: Between #2D+ and E1
CH2: Between #2D- and E1 |
|
| CH1: Between #3D+ and E1
CH2: Between #3D- and E1 |
|
| CH1: Between #4D+ and E1
CH2: Between #4D- and E1 |
|
| Tester Range | 50 V/DIV., 200 μs./DIV. |
| Condition | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" |
WAVEFORM 13
| ECM Terminal Name | CH1: Between FP1+ and E1
CH2: Between FP1- and E1 |
| Tester Range | 20 V/DIV., 500 μs./DIV. |
| Condition | Idling with warm engine, Data List item "Injection Mode" displaying "Direct" |
WAVEFORM 14
| ECM Terminal Name | CH1: Between VOP+ and E1
CH2: Between VOP- and E1 |
| Tester Range | 5 V/DIV., 2 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 15
| ECM Terminal Name | Between OE1+ and OE1- |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
WAVEFORM 16
| ECM Terminal Name | Between EDT1 and E1 |
| Tester Range | 2 V/DIV., 5 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 17
| ECM Terminal Name | Between IGT (1 to 4) and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 18
| ECM Terminal Name | Between WPO and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the engine water pump assembly speed.
WAVEFORM 19
| ECM Terminal Name | Between WPI and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine water pump assembly speed increases.
WAVEFORM 20
| ECM Terminal Name | Between NIMO and E1 |
| Tester Range | 1 V/DIV., 2 ms./DIV. |
| Condition | Engine idling and clutch pedal fully released |
WAVEFORM 21
| ECM Terminal Name | Between PRG and E1 |
| Tester Range | 10 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine, under purge control |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 22
| ECM Terminal Name | Between EMR1 and E1 |
| Tester Range | 2 V/DIV., 5 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 23
| ECM Terminal Name | Between EMD1 and E1 |
| Tester Range | 2 V/DIV., 100 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 24
| ECM Terminal Name | Between #10 (to #40) and E1 |
| Tester Range | 10 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine (Data List item "Injection Mode" displaying "Port") |
The wavelength becomes shorter as the engine speed increases.
When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.
WAVEFORM 25
| ECM Terminal Name | CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 26
| ECM Terminal Name | Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 27
| ECM Terminal Name | Between VG and E2G |
| Tester Range | 1 V/DIV., 100 μs./DIV. |
| Condition | Ignition switch ON |
WAVEFORM 28
| ECM Terminal Name | Between KNK1 and EKNK |
| Tester Range | 1 V/DIV., 1 ms./DIV. |
| Condition | Engine speed maintained at 4000 rpm after warming up engine |
The wavelength becomes shorter as the engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle.