The GPF (Gasoline Particulate Filter) system is an exhaust purification system for processing the PM (Particulate Matter) discharged from the engine. The GPF catalyst has a porous ceramic structure that collects PM, and the collected PM is oxidized as it bonds with oxygen molecules under high temperature. When the fuel cut operation is performed after the GPF rises to a high temperature under high load operation, PM is oxidized, but under low temperature conditions, PM oxidation is insufficient and deposits accumulate. When the GPF is clogged by PM and "Exhaust Filter Full" is displayed on the multi-information display or GPF warning light is comes on, perform particulate filter regeneration using the GTS.
A differential pressure sensor is installed to monitor the pressure before the GPF catalyst converter. The sensor is a semiconductor type that is not affected by the exhaust gas. The differential pressure sensor outputs the difference between the atmospheric pressure and the pressure before the GPF catalyst.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P244B00 | Particulate Filter Differential Pressure Too High Bank 1 | When it is estimated that the GPF differential pressure will increase to the limit value or more and the intake air flow does not exceed 80 gm/sec*1 (1 trip detection logic). | ·
Front exhaust pipe assembly (GPF) ·
Differential pressure sensor ·
Mass air flow meter sub-assembly ·
Wire harness or connector ·
ECM |
Comes on*/-
*: The MIL is illuminated when PM or ash accumulation has progressed and protection of parts has become necessary. |
DTC stored | SAE: P244B |
*1: Varies with exhaust gas temperature
When particulate matter and ash accumulate in the GPF, it becomes difficult for the exhaust gas to flow and the GPF differential pressure increases, so the ECM limits the intake air flow to protect parts.
After the limit value of the intake air flow drops below the threshold, if a driving operation equal to or higher than the current load is performed and it is estimated that the GPF differential pressure will increase to the limit value or more, when the intake air flow reaches the limit value, excessive accumulation is detected in the GPF, a DTC is output and the MIL illuminates.
| Frequency of Operation | Once per driving cycle |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Idle the engine for 5 minutes or more [A].
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) [depress the accelerator pedal by a large amount at 2nd shift position] and then decelerating the vehicle 5 times [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P244B00.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [A] through [C] again.
Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P010012
Refer to DTC P245211 for the differential pressure sensor circuit.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P245211
Clear the Vehicle Control History after completing repairs.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Record the Vehicle Control History.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Vehicle Control History code X0858, X0859 or DTC P244B00 is output | A |
| DTC P244B00 and other DTCs are output | B |
If any DTCs other than P244B00 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Ash Deposition Ratio Bank1.
| Tester Display |
|---|
| Ash Deposition Ratio Bank1 |
Read the value displayed on the GTS.
| GTS Display | Specified Condition |
|---|---|
| Ash Deposition Ratio Bank1 | Less than 100% |
| Proceed to |
|---|
| OK |
| NG |
Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly (GPF).
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank 1.
| Tester Display |
|---|
| PM Deposition Ratio Bank1 |
Read the values displayed on the GTS.
Data List item "PM Deposition Ratio Bank1" is necessary after performing particulate filter regeneration. Therefore, make sure check them.
| Proceed to |
|---|
| NEXT |
NEXT
Perform the PM Regenerate Mode.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank1.
| Tester Display |
|---|
| PM Deposition Ratio Bank1 |
Read the value displayed on the GTS.
| GTS Display | Specified Condition |
|---|---|
| PM Deposition Ratio Bank1 | Less than 30% |
After performing particulate filter regeneration, if the value of Data List items "PM Deposition Ratio Bank1" is less than the value during step 4 (READ VALUE USING GTS (PM DEPOSITION RATIO)), the driving condition may not be suitable for particulate filter regeneration. Therefore, perform particulate filter regeneration again.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P244B00 is output | B |
A
B
Inspect the differential pressure sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.
Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Mass Air Flow Sensor | ·
Shift lever position: P or neutral ·
A/C: Off ·
Engine warmed up ·
Engine Speed: 3000 rpm |
Between 8.0 and 13.0 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly (GPF).
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
OK
NG
| *a | Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly) |
Disconnect the mass air flow meter sub-assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C17-3 (VCC) - C17-2 (E2G) | Ignition switch ON | 4.8 to 5.2 V |
| C17-1 (FG) - C17-2 (E2G) | Ignition switch ON | 4.8 to 5.2 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C17-3 (VCC) - C17-1 (FG) | Ignition switch off | 2.09 to 2.31 kΩ |
| C17-2 (E2G) - Body ground | Always | Below 1 Ω |
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C17-3 (VCC) - C40-78 (VCVG) | Always | Below 1 Ω |
| C17-1 (FG) - C40-101 (VG) | Always | Below 1 Ω |
| C17-2 (E2G) - C40-79 (E2G) | Always | Below 1 Ω |
| C17-3 (VCC) or C40-78 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C17-1 (FG) or C40-101 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C17-2 (E2G) or C40-79 (E2G) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the differential pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C53-3 (VC) - C40-69 (VCPX) | Always | Below 1 Ω |
| C53-2 (PEX) - C40-92 (PEX) | Always | Below 1 Ω |
| C53-1 (E2) - C40-68 (EPEX) | Always | Below 1 Ω |
| C53-3 (VC) or C40-69 (VCPX) - Body ground and other terminals | Always | 10 kΩ or higher |
| C53-2 (PEX) or C40-92 (PEX) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the differential pressure sensor.
Click hereEngine / Hybrid System>M20A-FKS (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(w/ GPF)>REMOVAL
Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher (A).
Turn the ignition switch off and wait for 30 seconds or more (B).
Repeat the above procedures (A) and (B) 3 times.
Procedures (A) and (B) must be repeated 3 times to complete the differential pressure sensor learning process.
| Proceed to |
|---|
| NEXT |
NEXT