Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B157011  Indicator (Red) Circuit Short to Ground  B157013  Indicator (Red) Circuit Open  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157011 Indicator (Red) Circuit Short to Ground Manual (SOS) switch indicator (red) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light sub-assembly (manual [SOS] switch)

·

Harness or connector


B157013 Indicator (Red) Circuit Open Manual (SOS) switch indicator (red) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light sub-assembly (manual [SOS] switch)

·

Harness or connector



WIRING DIAGRAM

E354565E60
1.302,0.958 1.76,1.156 0.458,0.198 10 false RED 2.99,0.604 3.313,0.938 0.323,0.333 10 false 10 3,1.146 3.313,1.385 0.313,0.24 10 false 14 2.531,0.625 3.146,0.823 0.615,0.198 10 false IND1 2.469,1.156 3.083,1.354 0.615,0.198 10 false GND3 0.865,2.094 1.323,2.292 0.458,0.198 10 false P20 0.854,2.26 2.885,2.688 2.031,0.427 10 false Map Light Sub-assembly 4.938,0.594 5.25,0.792 0.313,0.198 10 false 4 4.938,1.156 5.25,1.354 0.313,0.198 10 false 3 5.167,0.729 5.781,0.927 0.615,0.198 10 false IND1 5.167,1.167 5.781,1.365 0.615,0.198 10 false SIG- 4.615,2.073 5.552,2.323 0.938,0.25 10 false H10 4.615,2.229 7.052,2.729 2.438,0.5 10 false Telephone Transceiver Assembly 0.958,1.677 2.99,2.104 2.031,0.427 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



HINT:

If DTC B157011 or B157013 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL [SOS] SWITCH) (RED INDICATOR)
2.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL [SOS] SWITCH) (RED INDICATOR)
a.
E434905C14
1.229,1.229 1.052,0.51 1.052,0.51 0.854,0.51 true 2.688,1.906 2.552,1.906 2.552,1.906 2.375,1.417 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.729,1.833 3.25,2.052 0.521,0.219 10 false GND3 0.5,0.427 0.938,0.635 0.438,0.208 10 false IND1
*a Component without harness connected
(Map Light Sub-assembly [Manual (SOS) Switch])


Remove the map light sub-assembly (manual [SOS] switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 10 (IND1) and a negative (-) lead to terminal 14 (GND3) of the map light sub-assembly (manual [SOS] switch) connector.


d.

Check if the manual (SOS) switch indicator (red) illuminates.

OK:

Manual (SOS) switch indicator (red) illuminates.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY [MANUAL (SOS) SWITCH])

NG

REPLACE MAP LIGHT SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY [MANUAL (SOS) SWITCH])
a.

Disconnect the H10 telephone transceiver assembly connector.


b.

Disconnect the P20 map light sub-assembly (manual [SOS] switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-4 (IND1) - P20-10 (IND1) Always Below 1 Ω
H10-4 (IND1) or P20-10 (IND1) - Body ground Always 10 kΩ or higher
H10-3 (SIG-) - P20-14 (GND3) Always Below 1 Ω
H10-3 (SIG-) or P20-14 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT