Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a communication telematics box*1 or telephone microphone assembly*2 signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157213 Microphone Circuit Open Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telephone transceiver assembly

·

Communication telematics box*1

·

Telephone microphone assembly*2

·

Harness or connector

·

Mayday wire*1

·

Map light sub-assembly



*1: w/ Communication telematics box

*2: w/o Communication telematics box

WIRING DIAGRAM

E405960E09
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 0.99,2.594 1.604,2.792 0.615,0.198 10 false MICV 0.938,3.375 1.552,3.573 0.615,0.198 10 false MIC1+ 0.917,2.958 1.531,3.156 0.615,0.198 10 false MIC2+ 1.042,3.792 1.656,3.99 0.615,0.198 10 false MCI- 5.667,1.396 6.281,1.594 0.615,0.198 10 false MCMD 5.667,1.781 6.281,1.979 0.615,0.198 10 false SP+ 5.667,2.198 6.281,2.396 0.615,0.198 10 false SP- 5.656,2.583 6.271,2.781 0.615,0.198 10 false MICV 5.646,3 6.26,3.198 0.615,0.198 10 false MCVD 5.656,3.365 6.271,3.563 0.615,0.198 10 false MCI+ 5.656,3.771 6.271,3.969 0.615,0.198 10 false MCI- 5.531,4.792 6.927,5.469 1.396,0.677 10 false Telephone Transceiver Assembly 4.031,3.99 4.688,4.219 0.656,0.229 10 false * 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.583 1.146,4.99 0.771,0.406 10 false P 2.104,1.302 2.719,1.5 0.615,0.198 10 false MCMD 2.26,1.698 2.875,1.896 0.615,0.198 10 false SP+ 2.302,2.104 2.917,2.302 0.615,0.198 10 false SP- 2.198,2.479 2.813,2.677 0.615,0.198 10 false MICV 2.219,3.302 2.833,3.5 0.615,0.198 10 false MIC2 2.219,2.906 2.833,3.104 0.615,0.198 10 false MIC1 2.229,3.677 2.844,3.875 0.615,0.198 10 false MCI- 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.469,2.104 2.083,2.302 0.615,0.198 10 false 8 1.479,2.5 2.094,2.698 0.615,0.198 10 false 5 1.5,3.292 2.115,3.49 0.615,0.198 10 false 2 1.5,2.896 2.115,3.094 0.615,0.198 10 false 7 1.49,3.677 2.104,3.875 0.615,0.198 10 false 4 2.76,1.219 3.375,1.417 0.615,0.198 10 false 1 2.76,1.615 3.375,1.813 0.615,0.198 10 false 3 2.76,2 3.375,2.198 0.615,0.198 10 false 9 2.792,2.406 3.406,2.604 0.615,0.198 10 false 6 2.74,3.208 3.354,3.406 0.615,0.198 10 false 10 2.76,2.802 3.375,3 0.615,0.198 10 false 11 2.771,3.594 3.385,3.792 0.615,0.198 10 false 5 5.344,1.677 5.958,1.875 0.615,0.198 10 false 18 5.385,1.292 6,1.49 0.615,0.198 10 false 8 5.354,2.073 5.969,2.271 0.615,0.198 10 false 34 5.354,2.458 5.969,2.656 0.615,0.198 10 false 24 5.396,2.865 6.021,3.063 0.625,0.198 10 false 5 5.396,3.656 6.021,3.854 0.625,0.198 10 false 7 5.531,4.604 6.302,5.01 0.771,0.406 10 false H10 2.688,1.406 3.458,1.813 0.771,0.406 10 false P18 5.646,4.198 6.26,4.396 0.615,0.198 10 false SGND 5.354,4.083 5.979,4.281 0.625,0.198 10 false 23 1.667,4.615 2.781,5.094 1.115,0.479 10 false Mayday Wire 2.688,1.781 3.458,2.188 0.771,0.406 10 false P18 2.698,2.198 3.469,2.604 0.771,0.406 10 false P18 2.719,2.583 3.49,2.99 0.771,0.406 10 false P18 2.688,2.979 3.458,3.385 0.771,0.406 10 false P18 2.698,3.375 3.469,3.781 0.771,0.406 10 false P18 2.688,3.771 3.458,4.177 0.771,0.406 10 false P18 5.396,3.26 6.021,3.458 0.625,0.198 10 false 6 0.177,0.156 5.865,0.396 5.688,0.24 12 false w/ Communication Telematics Box: 0.344,5.458 2.521,5.781 2.177,0.323 10 false *: Shielded

E384839E31
0.729,0.854 1.26,1.063 0.531,0.208 10 false MACC 0.813,1.323 1.271,1.531 0.458,0.208 10 false MIC+ 0.823,1.802 1.281,2.01 0.458,0.208 10 false MIC- 0.292,2.229 1.698,2.604 1.406,0.375 10 false Telephone Microphone Assembly 1.313,0.76 1.469,0.958 0.156,0.198 10 false 5 1.313,1.24 1.469,1.438 0.156,0.198 10 false 3 1.313,1.708 1.469,1.906 0.156,0.198 10 false 2 2.063,0.75 2.219,0.948 0.156,0.198 10 false 9 2.073,1.219 2.229,1.417 0.156,0.198 10 false 8 2.073,1.708 2.229,1.906 0.156,0.198 10 false 7 1.521,0.76 2.052,0.969 0.531,0.208 10 false MACC 1.531,1.25 2.063,1.458 0.531,0.208 10 false MCO+ 1.542,1.719 2.073,1.927 0.531,0.208 10 false MCO- 0.396,3.146 0.896,3.417 0.5,0.271 10 false P20 0.406,3.313 2.167,3.656 1.76,0.344 10 false Map Light Sub-assembly 5.646,0.76 5.885,0.958 0.24,0.198 10 false 5 5.646,1.24 5.885,1.438 0.24,0.198 10 false 6 5.656,1.719 5.896,1.917 0.24,0.198 10 false 7 5.615,2.292 5.854,2.49 0.24,0.198 10 false 23 5.938,0.833 6.469,1.042 0.531,0.208 10 false MCVD 5.917,1.323 6.448,1.531 0.531,0.208 10 false MCI+ 5.927,2.385 6.458,2.594 0.531,0.208 10 false SGND 5.917,1.792 6.448,2 0.531,0.208 10 false MCI- 5.521,2.76 6.208,3.073 0.688,0.313 10 false H10 5.51,2.927 6.906,3.625 1.396,0.698 10 false Telephone Transceiver Assembly 3.781,2.323 3.938,2.49 0.156,0.167 10 false * 2.49,3.344 3.552,3.573 1.063,0.229 10 false *: Shielded 0.167,0.063 6.042,0.302 5.875,0.24 12 false w/o Communication Telematics Box:

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds.


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (w/ Communication Telematics Box) B
NG (w/o Communication Telematics Box) C



A

B

2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)

C

7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
a.

Disconnect the H10 telephone transceiver assembly connector.


b.

Disconnect the P18 mayday wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-8 (MCMD) - P18-1 (MCMD) Always Below 1 Ω
H10-18 (SP+) - P18-3 (SP+) Always Below 1 Ω
H10-34 (SP-) - P18-9 (SP-) Always Below 1 Ω
H10-24 (MICV) - P18-6 (MICV) Always Below 1 Ω
H10-5 (MCVD) - P18-11 (MIC1) Always Below 1 Ω
H10-6 (MCI+) - P18-10 (MIC2) Always Below 1 Ω
H10-7 (MCI-) - P18-5 (MCI-) Always Below 1 Ω
H10-8 (MCMD) or P18-1 (MCMD) - Body ground Always 10 kΩ or higher
H10-18 (SP+) or P18-3 (SP+) - Body ground Always 10 kΩ or higher
H10-34 (SP-) or P18-9 (SP-) - Body ground Always 10 kΩ or higher
H10-24 (MICV) or P18-6 (MICV) - Body ground Always 10 kΩ or higher
H10-5 (MCVD) or P18-11 (MIC1) - Body ground Always 10 kΩ or higher
H10-6 (MCI+) or P18-10 (MIC2) - Body ground Always 10 kΩ or higher
H10-7 (MCI-) or P18-5 (MCI-) - Body ground Always 10 kΩ or higher
H10-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)
a.
E409641C01
1.49,2.823 1.865,3.083 0.375,0.26 1.521,0.365 1.896,0.625 0.375,0.26 2.177,1.281 2.646,1.281 true 1.313,3.208 1.708,3.729 true 1.823,1.271 2.542,0.708 true 1.823,1.604 2.479,2.031 true 0.781,1.292 1.208,1.292 true 1.583,1.615 0.938,2.177 true 1.385,1.583 0.906,1.792 true 1.406,1.219 0.896,0.917 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.583,0.417 1.896,0.615 0.313,0.198 10 false P18 2.688,1.208 3.271,1.583 0.583,0.375 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 2.583,0.625 3.167,1 0.583,0.375 10 false SP+ 2.531,1.969 3.115,2.344 0.583,0.375 10 false SP- 0.417,1.219 1,1.594 0.583,0.375 10 false MICV 0.594,2.104 1.094,2.458 0.5,0.354 10 false MIC2 0.563,0.823 1.146,1.198 0.583,0.375 10 false MCI- 0.552,1.719 1.135,2.094 0.583,0.375 10 false MIC1 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI-
*a Component without harness connected
(Wire Harness)
*b Component without harness connected
(Communication Telematics Box)


Disconnect the P18 wire harness connector.


b.

Disconnect the P communication telematics box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P18-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
P18-3 (SP+) - P-3 (SP+) Always Below 1 Ω
P18-9 (SP-) - P-8 (SP-) Always Below 1 Ω
P18-6 (MICV) - P-5 (MICV) Always Below 1 Ω
P18-10 (MIC2) - P-2 (MIC1+) Always Below 1 Ω
P18-11 (MIC1) - P-7 (MIC2+) Always Below 1 Ω
P18-5 (MCI-) - P-4 (MCI-) Always Below 1 Ω
P18-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
P18-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
P18-9 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
P18-6 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
P18-10 (MIC2) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
P18-11 (MIC1) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
P18-5 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442560C06
1.385,0.573 1.958,0.885 0.573,0.313 2.26,1.948 2.458,2.74 2.458,2.74 2.625,2.74 true 2.292,1.813 2.563,0.969 2.563,0.969 2.729,0.969 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 1.563,0.646 2.104,0.865 0.542,0.219 10 false H10 2.802,0.896 3.344,1.115 0.542,0.219 10 false MCI- 2.677,2.667 3.219,2.885 0.542,0.219 10 false MICV
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H10-24 (MICV) - Body ground Ignition switch ON 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
H10-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK COMMUNICATION TELEMATICS BOX

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
5.CHECK COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL


b.

Turn the ignition switch to ON and wait for 10 seconds.


c.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

d.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION TELEMATICS BOX IS DEFECTIVE)

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the H10 telephone transceiver assembly connector.


b.

Disconnect the P20 map light sub-assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-5 (MCVD) - P20-9 (MACC) Always Below 1 Ω
H10-6 (MCI+) - P20-8 (MCO+) Always Below 1 Ω
H10-7 (MCI-) - P20-7 (MCO-) Always Below 1 Ω
H10-5 (MCVD) or P20-9 (MACC) - Body ground Always 10 kΩ or higher
H10-6 (MCI+) or P20-8 (MCO+) - Body ground Always 10 kΩ or higher
H10-7 (MCI-) or P20-7 (MCO-) - Body ground Always 10 kΩ or higher
H10-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442560C07
1.385,0.573 1.958,0.885 0.573,0.313 2.479,1.802 2.75,0.958 2.75,0.958 2.917,0.958 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 1.563,0.646 2.104,0.865 0.542,0.219 10 false H10 2.979,0.875 3.406,1.125 0.427,0.25 10 false MCVD
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H10-5 (MCVD) - Body ground Ignition switch ON 4 to 6 V



Result:
Proceed to
OK
NG



OK

9.INSPECT MAP LIGHT SUB-ASSEMBLY

NG

12.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
9.INSPECT MAP LIGHT SUB-ASSEMBLY
a.
E434906C05
1.521,3.052 1.917,3.302 0.396,0.25 1.479,0.802 1.875,1.052 0.396,0.25 2.427,0.854 2.26,0.854 2.26,0.854 1.635,1.719 true 1.479,1.74 1.198,0.771 1.198,0.771 1.01,0.771 true 1.573,3.854 1.344,4.385 1.344,4.385 1.156,4.385 true 1.708,3.844 1.896,4.375 1.896,4.375 2.094,4.375 true 2,3.844 2.24,4.177 2.24,4.177 2.438,4.177 true 1.344,1.708 1.063,1 1.063,1 0.875,1 true 0.146,0.208 0.458,0.406 0.313,0.198 10 false *a 1.667,3.094 1.979,3.292 0.313,0.198 10 false B 0.854,4.302 1.333,4.51 0.479,0.208 10 false MIC- 2.5,0.781 3.073,1.021 0.573,0.24 10 false MCO- 0.594,0.688 1.167,0.927 0.573,0.24 10 false MCO+ 2.135,4.281 2.615,4.49 0.479,0.208 10 false MIC+ 2.5,4.094 3.073,4.333 0.573,0.24 10 false MACC 0.427,0.927 1,1.167 0.573,0.24 10 false MACC 1.646,0.854 1.958,1.052 0.313,0.198 10 false A
*a Component without harness connected
(Map Light Sub-assembly)


Remove the map light sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-9 (MACC) - B-5 (MACC) Always Below 1 Ω
A-8 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-7 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-9 (MACC) - A-8 (MCO+) Always 10 kΩ or higher
A-9 (MACC) - A-7 (MCO-) Always 10 kΩ or higher
A-8 (MCO+) - A-7 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT SUB-ASSEMBLY

10.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


b.

Turn the ignition switch to ON and wait for 10 seconds.


c.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

d.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT