Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15C111  GNSS Antenna Circuit Short to Ground  B15C113  GNSS Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C111 GNSS Antenna Circuit Short to Ground Current to the roof antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Antenna divider

·

No. 2 antenna cord sub-assembly


B15C113 GNSS Antenna Circuit Open Current to the roof antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Antenna divider

·

No. 2 antenna cord sub-assembly



WIRING DIAGRAM

E385666E08
5.688,6.594 6.563,7.344 0.875,0.75 10 false Roof Antenna Assembly 3.906,1.75 5.344,2.51 1.438,0.76 10 false Telephone Transceiver Assembly 2.25,1.563 3.531,2.542 1.281,0.979 10 false No. 2 Antenna Cord Sub-assembly 0.552,6.573 1.74,7.563 1.188,0.99 10 false Antenna Cord Sub-assembly 2.323,6.563 3.615,7.677 1.292,1.115 10 false No. 3 Antenna Cord Sub-assembly 4.01,6.583 5.229,7.448 1.219,0.865 10 false No. 4 Antenna Cord Sub-assembly 5.385,6.198 6.573,7.188 1.188,0.99 10 false A 5.375,5.604 6.563,6.594 1.188,0.99 10 false A 1.958,5.615 3.146,6.604 1.188,0.99 10 false C 1.969,6.198 3.156,7.188 1.188,0.99 10 false C 3.542,0.771 4.729,1.76 1.188,0.99 10 false ANT2 3.656,1.01 4.844,2 1.188,0.99 10 false 1a 3.677,0.552 4.865,1.542 1.188,0.99 10 false 1 3.677,5.625 4.865,6.521 1.188,0.896 10 false B 3.688,6.208 4.875,7.198 1.188,0.99 10 false B 2.333,4.563 3.51,5.615 1.177,1.052 10 false Antenna Divider 1.958,3.771 3.177,5.198 1.219,1.427 10 false D 1.969,4.229 3.188,5.656 1.219,1.427 10 false D 1.969,3.313 3.188,4.74 1.219,1.427 10 false D 1.958,2.885 3.177,4.313 1.219,1.427 10 false D 1.969,1.219 3.156,2.208 1.188,0.99 10 false E 1.958,0.771 3.146,1.76 1.188,0.99 10 false E 5.385,5.417 6.573,6.406 1.188,0.99 10 false 5 5.354,5.99 6.542,6.979 1.188,0.99 10 false 5a 3.635,6 4.823,6.99 1.188,0.99 10 false 1a 3.677,5.406 4.865,6.396 1.188,0.99 10 false 1 1.958,5.396 3.146,6.385 1.188,0.99 10 false 1 1.927,5.99 3.115,6.979 1.188,0.99 10 false 1a 1.969,2.677 3.156,3.667 1.188,0.99 10 false 5 1.938,3.125 3.125,4.115 1.188,0.99 10 false 5a 1.948,3.583 3.135,4.573 1.188,0.99 10 false 6 1.927,4.031 3.115,5.021 1.188,0.99 10 false 6a 1.927,1 3.115,1.99 1.188,0.99 10 false 1a 1.969,0.563 3.156,1.552 1.188,0.99 10 false 1 3.542,1.229 4.729,2.219 1.188,0.99 10 false ANT2

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
2.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E389828C05
1.479,0.302 1.917,0.521 0.438,0.219 1.469,2.729 1.906,2.948 0.438,0.219 2.167,4.198 2.292,4.198 2.292,4.198 2.458,3.646 true 2.365,0.99 2.26,0.99 2.26,0.99 1.833,1.354 true 2.417,0.896 2.875,1.271 0.458,0.375 10 false 5a 1.958,4.115 2.271,4.313 0.313,0.198 10 false 1a 1.646,0.344 1.958,0.542 0.313,0.198 10 false A 1.635,2.771 1.948,2.969 0.313,0.198 10 false B 0.333,0.281 0.646,0.479 0.313,0.198 10 false *a 0.323,2.625 0.635,2.823 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 4 antenna cord sub-assembly from the roof antenna assembly connector.


b.

Disconnect the No. 4 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-5 - B-1 Always Below 1 Ω
A-5a - B-1a Always Below 1 Ω
A-5 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E383188C04
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 0.875,3.365 1.198,3.969 1.198,3.969 1.323,3.969 true 0.875,1.49 1.198,2.073 1.198,2.073 1.323,2.073 true 1.625,0.469 2,0.708 0.375,0.24 10 false B 1.625,2.406 2,2.646 0.375,0.24 10 false C 1.375,2 1.75,2.24 0.375,0.24 10 false 1a 1.354,3.906 1.729,4.146 0.375,0.24 10 false 1a 0.24,0.292 0.552,0.448 0.313,0.156 10 false *a 0.198,2.333 0.51,2.49 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly from the No. 4 antenna cord sub-assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - C-1 Always Below 1 Ω
B-1a - C-1a Always Below 1 Ω
B-1 or C-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E405967C03
1.552,1.75 1.958,1.99 0.406,0.24 1.531,0.271 1.938,0.51 0.406,0.24 1.573,3.177 1.979,3.417 0.406,0.24 1.198,3.979 1.469,4.406 1.469,4.406 1.594,4.406 true 2.479,2.448 2.729,2.063 2.729,2.063 2.854,2.063 true 2.146,2.563 2.365,3.021 2.365,3.021 2.49,3.021 true 2.396,1.125 2.563,1.479 2.563,1.479 2.688,1.479 true 1.677,0.323 2.052,0.563 0.375,0.24 10 false C 1.625,2.406 2,2.646 0.375,0.24 10 false E 2.906,1.979 3.281,2.219 0.375,0.24 10 false 6a 1.656,4.323 2.031,4.563 0.375,0.24 10 false 1a 1.698,1.792 2.073,2.031 0.375,0.24 10 false D 1.719,3.219 2.094,3.458 0.375,0.24 10 false E 2.552,2.938 2.927,3.177 0.375,0.24 10 false 5a 2.719,1.396 3.094,1.635 0.375,0.24 10 false 1a 0.302,0.167 0.677,0.406 0.375,0.24 10 false *a 0.302,1.792 0.677,2.031 0.375,0.24 10 false *b 0.365,3.135 0.74,3.375 0.375,0.24 10 false *c
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)
*c Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the antenna cord sub-assembly from the antenna divider connector.


c.

Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-1 - D-6 Always Below 1 Ω
C-1a - D-6a Always Below 1 Ω
D-5 - E-1 Always Below 1 Ω
D-5a - E-1a Always Below 1 Ω
C-1 or D-6 - Body ground Always 10 kΩ or higher
D-5 or E-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA DIVIDER

NG

5.INSPECT ANTENNA DIVIDER
a.
E241596C20
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Remove the antenna divider.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 - 6 Always Below 1 Ω
5a - 6a Always Below 1 Ω
5 - 5a Always 10 kΩ or higher
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E421944C02
1.5,0.417 1.917,0.667 0.417,0.25 1.5,2.698 1.917,2.948 0.417,0.25 2.135,4.219 1.76,3.865 true 2.688,2 2.531,1.625 true 0.49,0.344 0.802,0.542 0.313,0.198 10 false *a 2.177,4.208 2.49,4.406 0.313,0.198 10 false 1a 2.646,2.031 2.958,2.229 0.313,0.198 10 false 1a 1.667,0.458 1.979,0.656 0.313,0.198 10 false E 0.49,2.635 0.802,2.833 0.313,0.198 10 false *b 1.531,2.74 1.958,2.906 0.427,0.167 10 false ANT2
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - ANT2-1 Always Below 1 Ω
E-1a - ANT2-1a Always Below 1 Ω
E-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ROOF ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ROOF ANTENNA ASSEMBLY IS DEFECTIVE)

NG

8.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
8.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT