Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telephone transceiver assembly, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15CB11 Telephone Main Antenna Circuit Short to Ground Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly


B15CB13 Telephone Main Antenna Circuit Open Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly



WIRING DIAGRAM

E383187E25
3.927,4.979 4.781,5.604 0.854,0.625 10 false Roof Antenna Assembly 5.552,2.104 6.958,2.823 1.406,0.719 10 false Telephone Transceiver Assembly 2.229,1.938 3.469,2.927 1.24,0.99 10 false Antenna Cord Sub-assembly 3.656,4.031 4.844,5.021 1.188,0.99 10 false A 3.656,4.625 4.844,5.615 1.188,0.99 10 false A 1.938,4.021 3.125,5.01 1.188,0.99 10 false B 1.948,4.615 3.135,5.604 1.188,0.99 10 false B 5.219,0.99 6.406,1.979 1.188,0.99 10 false ANT1 3.667,3.802 4.854,4.792 1.188,0.99 10 false 4 3.635,4.417 4.823,5.406 1.188,0.99 10 false 4a 1.958,3.823 3.146,4.813 1.188,0.99 10 false 2 1.917,4.396 3.104,5.385 1.188,0.99 10 false 2a 1.958,0.792 3.146,1.781 1.188,0.99 10 false 2 1.917,1.365 3.104,2.354 1.188,0.99 10 false 2a 3.656,0.802 4.844,1.792 1.188,0.99 10 false 2 3.625,1.375 4.813,2.365 1.188,0.99 10 false 2a 5.333,1.385 6.521,2.375 1.188,0.99 10 false 1a 5.344,0.792 6.531,1.781 1.188,0.99 10 false 1 1.948,1.594 3.135,2.583 1.188,0.99 10 false C 3.646,1.583 4.833,2.573 1.188,0.99 10 false E 3.646,0.979 4.833,1.969 1.188,0.99 10 false E 1.948,1 3.135,1.99 1.188,0.99 10 false C 3.927,1.938 5.198,2.927 1.271,0.99 10 false No. 2 Antenna Cord Sub-assembly 0.51,4.99 1.771,6.042 1.26,1.052 10 false No. 3 Antenna Cord Sub-assembly 2.24,4.958 3.521,5.958 1.281,1 10 false No. 4 Antenna Cord Sub-assembly 5.229,1.573 6.417,2.563 1.188,0.99 10 false ANT1

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 459

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

B

2.INSPECT ROOF ANTENNA ASSEMBLY
2.INSPECT ROOF ANTENNA ASSEMBLY
a.
E427104C01
1.927,1.573 2.094,1.844 2.094,1.844 2.344,1.844 true 0.896,0.417 1.208,0.615 0.313,0.198 10 false *a 2.406,1.75 2.719,1.948 0.313,0.198 10 false 4a
*a Component without harness connected
(Roof Antenna Assembly)


Remove the roof antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 9 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

3.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E389828C04
1.479,0.302 1.917,0.521 0.438,0.219 1.469,2.729 1.906,2.948 0.438,0.219 1.854,4.208 1.979,4.208 1.979,4.208 2.146,3.656 true 1.073,0.958 1.198,0.958 1.198,0.958 1.563,1.354 true 0.906,0.875 1.219,1.073 0.313,0.198 10 false 4a 1.656,4.125 1.969,4.323 0.313,0.198 10 false 2a 1.646,0.344 1.958,0.542 0.313,0.198 10 false A 1.635,2.771 1.948,2.969 0.313,0.198 10 false B 0.333,0.281 0.646,0.479 0.313,0.198 10 false *a 0.323,2.625 0.635,2.823 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 4 antenna cord sub-assembly from the roof antenna assembly connector.


b.

Disconnect the No. 4 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-2 Always Below 1 Ω
A-4a - B-2a Always Below 1 Ω
A-4 or B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E383188C01
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 1.271,3.375 1.594,3.979 1.594,3.979 1.719,3.979 true 1.281,1.5 1.604,2.083 1.604,2.083 1.729,2.083 true 1.625,0.469 2,0.708 0.375,0.24 10 false B 1.625,2.406 2,2.646 0.375,0.24 10 false C 1.792,2.01 2.167,2.25 0.375,0.24 10 false 2a 1.771,3.906 2.146,4.146 0.375,0.24 10 false 2a 0.313,0.302 0.625,0.458 0.313,0.156 10 false *a 0.406,2.24 0.719,2.396 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly from the No. 4 antenna cord sub-assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 Always Below 1 Ω
B-2a - C-2a Always Below 1 Ω
B-2 or C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E385192C01
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 1.24,3.458 1.563,4.063 1.563,4.063 1.688,4.063 true 2.198,1.552 2.49,2.156 2.49,2.156 2.615,2.156 true 1.625,0.469 2,0.708 0.375,0.24 10 false C 1.625,2.406 2,2.646 0.375,0.24 10 false E 2.677,2.052 3.052,2.292 0.375,0.24 10 false 2a 1.75,3.958 2.125,4.198 0.375,0.24 10 false 2a 0.229,0.146 0.542,0.302 0.313,0.156 10 false *a 0.24,2.333 0.552,2.49 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - E-2 Always Below 1 Ω
C-2a - E-2a Always Below 1 Ω
C-2 or E-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E421943C03
1.5,0.417 1.917,0.667 0.417,0.25 1.5,2.698 1.917,2.948 0.417,0.25 2.135,4.219 1.76,3.865 true 2.375,2.115 2.167,1.625 true 0.49,0.344 0.802,0.542 0.313,0.198 10 false *a 2.177,4.208 2.49,4.406 0.313,0.198 10 false 1a 2.354,2.146 2.667,2.344 0.313,0.198 10 false 2a 1.667,0.458 1.979,0.656 0.313,0.198 10 false E 0.49,2.635 0.802,2.833 0.313,0.198 10 false *b 1.531,2.74 1.958,2.906 0.427,0.167 10 false ANT1
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the No. 2 antenna cord sub-assembly connector from the antenna cord sub-assembly.


b.

Disconnect the No. 2 antenna cord sub-assembly connector from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 - ANT1-1 Always Below 1 Ω
E-2a - ANT1-1a Always Below 1 Ω
E-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT