Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) J

TELEMATICS  TELEMATICS SYSTEM(for eCall)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E418549E92
2.469,2.24 2.938,2.406 0.469,0.167 10 false H10 2.469,2.396 3.844,2.802 1.375,0.406 10 false Telephone Transceiver Assembly 4.563,2.615 4.938,2.823 0.375,0.208 10 false P20 4.552,2.781 6.542,3.167 1.99,0.385 10 false Map Light Sub-assembly 4.208,0.896 4.469,1.115 0.26,0.219 10 false 24 4.198,1.698 4.51,1.938 0.313,0.24 10 false 14 4.458,0.906 4.844,1.083 0.385,0.177 10 false RRID 1.104,1.031 2.656,1.313 1.552,0.281 10 false from IG2 NO.2 Relay 4.458,1.719 4.927,1.896 0.469,0.177 10 false GND3 4.969,2.135 6.417,2.313 1.448,0.177 10 false Manual (SOS) Switch 2.823,1.198 3.938,1.396 1.115,0.198 10 false ECU-IG2 NO.3 3.292,1.823 3.76,2 0.469,0.177 10 false SIG- 3.708,1.708 4.021,1.948 0.313,0.24 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY)
a.

Disconnect the H10 telephone transceiver assembly connector.


b.

Disconnect the P20 map light sub-assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P20-24 (RRID) - Body Ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-3 (SIG-) - P20-14 (GND3) Always Below 1 Ω
H10-3 (SIG-) or P20-14 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT SUB-ASSEMBLY
a.
E434905C16
0.906,1.448 0.688,1.896 0.688,1.896 0.49,1.896 true 2.688,1.906 2.552,1.906 2.552,1.906 2.375,1.417 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.729,1.833 3.25,2.052 0.521,0.219 10 false GND3 0.125,1.823 0.563,2.031 0.438,0.208 10 false RRID
*a Component without harness connected
(Map Light Sub-assembly)


Remove the map light sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Apply auxiliary battery voltage to the connector.

Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → 24 (RRID)
Auxiliary battery negative (-) → 14 (GND3)
Always Manual (SOS) switch illumination comes on


c.

Check if the manual (SOS) switch illumination comes on.

OK:

The manual (SOS) switch illumination comes on.



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE MAP LIGHT SUB-ASSEMBLY

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT